Anderson RB-200 Bedienungsanleitung

This Quick start up guide does not replace in any way or form the

user manual of this unit.The intension of this document is for use

when setting up the machine after delivery to the dealer and before

the machine is transferred to the end user.This document should

be used as achecklist and memory aid for employees already

familiar with the guidelines in the user manual.Failure to operate

the product correctly can result in damage to the product, personal

property, and cause serious injury.This guide should not be

transferred to the owner of the machine.

QUICK START GUIDE

RB200

After receiving your machine you will want to set it up to be ready for any demo

opportunity or sale that may come along.Besides that, you want to be sure that the

machine is in factory condition, free of damage from transport and defective parts due

to the transport from our factory to your dealership.This is aquick guide that will help

you to be up and ready in ashort time.Before using the machine you must grease and

oil all points on the wrapper that require it.

Basics:

Single bale 3 point hitch wrapper.

•4 or 5ft bale

•1 stretcher (30’’)

•Plastic cutting knife

•Bale counter

Note: Before pressure washing the machine be sure to remove the computer (bale counter)

QUICK START GUIDE

RB200

QUICK START GUIDE (WITHOUT BALE)

RB200

Hook the machine to atractor to test it.Be sure that the tractor and the machine

are secured by the pins supplied with the machine.(See the below illustrations)

Attach the machine’s hoses to the tractor as

shown.Be sure that your tractor has enough

oil and follows the below requirements.

Remove the transport locking pin.Once

removed, the wrapper will split when lifted by

the 3point hitch on the tractor.This will cause

the bale to dump from the machine to the rear.

QUICK START GUIDE (WITH BALE)

RB200

When the machine is to be delivered to the user there are steps you must follow to be sure they are

comfortable with wrapping their first bale. These steps are also important if you are doing a live demo.

Setup is very important to bale size as this machine is not set to a specific bale at the factory.

1) Know your bale size before you start. Asking can help but an actual measurement of

the bale is sometimes necessary.

2) Be sure that everything is greased (if left for more than 3 months outside without use

the machine needs to be fully greased and oiled.

3) Your bale counter is charged and tested operational (see user manual on machine for

functions).

4) Be sure the tractor you are using is open center hydraulics and can handle the machine

weight.

The stretcher pole has 3 positions. Be sure that the position is

not over the height of the bale or under it. (This part is normally

removed for shipping so be sure to install it correctly to wrap

your bales)

Set the cone rollers for 4 or 5 foot

long bale.

Put plastic in the stretcher. There

is only one way to put the plastic

through. See the diagram to the

left. This is a sticker found on the

machine as well.

QUICK START GUIDE (WITH BALE)

RB200

Turn on the bale counter and set it up.

1) Press the ON button

2) You will have to set the counter up.To do so you will hold the Adjust Select for

3seconds.You can then scroll through 4menus with the same button (adjust

select)

3) Use the +and –to change the values in the menu.

4) When wrapping you will hear abuzzer from the counter on the last turn so

that you know when to stop turning the table.The number will automatically

reset once the sequence is finished.

Quick reference for correct plastic layers:

The way that we calculate the amount of plastic to apply on a bale is simple. You wrap the bale manually

once with only one layer of plastic. You do not want to see any part of the bale when you are finished. You

take the number of turns it took the table to do so and multiply it by 2 and then add one extra layer (or turn).

EX: 10 turns to completely cover the bale x 2 = 20. plus one layer = 21.

This is the number you want to program in your bale counter with.

Last step before wrapping a bale is to uncover the cutting knife.

For the first bale you can put the plastic like the

below image and sit a bale on the machine

Your bale is wrapped. Dump off with the 3 point of the tractor and load another bale.

Note: when dumping the bale, if you dump a little bit to one side (opposite the stretcher) you can sit your next bale directly on the tail of

plastic. When you start to turn the table the plastic will stay there and also cut from the previous bale as soon as you turn the table one turn.

Videos can be found on our website and also more in depth information in the user manual for the machine.

Andere Handbücher für RB-200

Inhaltsverzeichnis

Andere Anderson Landwirtschaftliche Geräte Handbücher

Anderson

Anderson TRB-2000 Bedienungsanleitung

Anderson

Anderson Double stretcher Bedienungsanleitung

Anderson

Anderson 680HS Bedienungsanleitung

Anderson

Anderson WRAPTOR Bedienungsanleitung

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson RBM1400 Bedienungsanleitung

Anderson

Anderson RB580 Bedienungsanleitung

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson RBMPRO Einrichtungshandbuch

Anderson

Anderson RB 680 Bedienungsanleitung

Anderson

Anderson TSR-3450 Bedienungsanleitung

Anderson

Anderson RB600 Fehlerbehebungshandbuch

Anderson

Anderson Fusion720 Bedienungsanleitung

Anderson

Anderson RB580 Bedienungsanleitung

Anderson

Anderson RB-400 Bedienungsanleitung

Anderson

Anderson RBM Series Bedienungsanleitung

Anderson

Anderson M-160 Bedienungsanleitung

Anderson

Anderson 590HS Bedienungsanleitung

Anderson

Anderson IFX720 Handbuch

Anderson

Anderson ROUND BALE WRAPPER HYBRID Bedienungsanleitung

Anderson

Anderson Fusion720 Bedienungsanleitung

Anderson

Anderson STACKPRO Series Einrichtungshandbuch

Anderson

Anderson GB series Bedienungsanleitung

Anderson

Anderson 680HS Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung