Anderson 680HS Bedienungsanleitung

This Quick start up guide does not replace in any way or form the

user manual of this unit. The intension of this document is for use

when setting up the machine after delivery to the dealer and before

the machine is transferred to the end user. This document should

be used as a checklist and memory aid for employees already

familiar with the guidelines in the user manual. Failure to operate

the product correctly can result in damage to the product, personal

property, and cause serious injury. This guide should not be

transferred to the owner of the machine.

QUICK START GUIDE

800HS

After receiving your machine you will want to set it up to be ready for any demo opportunity or sale

that may come along.Besides that, you want to be sure that the machine is in factory condition, free

of damage from transport and defective parts due to the transport from our factory to your dealership.

This is aquick guide that will help you to be up and ready in ashort time.Before using the machine

you must grease and oil all points on the wrapper that require it.

Basics:

Square bale wrapper

•Up to 6ft bale

•1 stretcher (30’’)

•Computer & remote

•Hydraulic plastic cut and hold

Note: Before pressure washing the machine be sure to remove the computer

QUICK START GUIDE

800HS

QUICK START GUIDE

800HS

When the machine is to be delivered to the user there are steps you must follow to be sure they are

comfortable with wrapping their first bale. These steps are also important if you are doing a live demo.

Setup is very important to bale size as this machine is not set to a specific bale at the factory.

1) Know your bale size before you start. Asking can help but an actual measurement of

the bale is sometimes necessary.

2) Be sure that everything is greased (if left for more than 3 months outside without use

the machine needs to be fully greased and oiled.

3) Your remote control is charged and tested operational (see user manual on machine for

functions).

The stretcher pole has 6 positions. Be sure that the position is

not over the height of the bale or under it. (this part could have

been removed for shipping so be sure to install it correctly for

wrapping bales)

Set the cone rollers for the size of

your bale.

Put plastic in the

stretcher. There is only

one way to put the plastic

through. See the diagram

to the left. This is a

sticker found on the

machine as well.

Turn on the computer.

1) Pull the emergency stop button (1), the blue

light (2) will come on.

2) Press the power button on the remote (3),

when the screen is ON push the power button

(3) again

3) Make sure the M.C. LED light (4) on the

receiver’s control panel is ON.

QUICK START GUIDE

800HS

Starting and Aligning the wrapper

1) If equipped with an Honda engine, put the

ignition key in the ON position and press the

start engine button on the remote.

2) Before wrapping you need to align the

wrapper, press the alignment key (5) on the

remote control.

3) When the alignment menu appears on the

remote control screen, press the same key (5)

asecond time, the alignment will start and the

screen should display Alignment in progress (it

can take up to 2minutes).

Receiver

Remote

Emergency control box

Start Wrapping

1) Make sure the blue button’s light (2) is on,

which means that the alignment is finished.

2) Push the wrap key (6), the wrapper’s table will

make the set number of rotation and

unloading will happen automatically, and will

engage the plastic cutter.

3) If the remote is not charged or missing you can

wrap automatically by pressing the blue

button (2).

Honda engine

The 800HS is powered by an Honda

engine.Before starting the machine

make sure it has gas and oil in it.Also

when traveling or not using the

machine for along period of time don’t

forget to close the fuel valve, located

beneath the choke on the right side of

the engine.

Fuel valve

QUICK START GUIDE

800HS

The 680HS is equipped with an

hydraulic cut and hold system.The

hydraulic cut and hold works with

the pressure of the main valve and

an accumulator.

If the plastic isn’t cut or not

completely you want to make sure

the blade is sharp and free of rust

first.If the rubber bumper doesn’t

hold the plastic you can put more

tension on the fingers and rubber

bumper by adjusting the bolt (1)

and the spring with the adjustment

rod (2).

Andere Handbücher für 680HS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Anderson Landwirtschaftliche Geräte Handbücher

Anderson

Anderson A-INL-032 Bedienungsanleitung

Anderson

Anderson NutriWrap 780 SB Bedienungsanleitung

Anderson

Anderson RB580 Bedienungsanleitung

Anderson

Anderson RB-500 Bedienerhandbuch

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson RB600 Fehlerbehebungshandbuch

Anderson

Anderson Fusion720 Bedienungsanleitung

Anderson

Anderson STACKPRO Series Einrichtungshandbuch

Anderson

Anderson GB series Bedienungsanleitung

Anderson

Anderson NWS-660 Bedienungsanleitung

Anderson

Anderson ROUND BALE WRAPPER HYBRID Bedienungsanleitung

Anderson

Anderson IFX720 Handbuch

Anderson

Anderson RB-400 Bedienungsanleitung

Anderson

Anderson TRB1000 Einrichtungshandbuch

Anderson

Anderson RB580 Bedienungsanleitung

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson Fusion720 Bedienungsanleitung

Anderson

Anderson RBMPRO Einrichtungshandbuch

Anderson

Anderson RBM1400 Bedienungsanleitung

Anderson

Anderson WRAPTOR Bedienungsanleitung

Anderson

Anderson 590HS Bedienungsanleitung

Anderson

Anderson M-160 Bedienungsanleitung

Anderson

Anderson 680HS Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung