Anritsu G0430A Bedienungsanleitung
Document No.: M-W4083AE-1.0
ANRITSU CORPORATION
G0430A
PCIe5 Re-Driver Set
Operation Manual
For safety and warning information, please read this
manual before attempting to use the equipment.
Keep this manual with the equipment.
First Edition
ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following
safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the symbols
BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu equipment. In addition,
there may be other labels attached to products that are not shown in the diagrams in this manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and
take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
G0430A
PCIe5 Re-Driver Set
Operation Manual
15 April 2022 (First Edition)
Copyright © 2022, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The operational instructions of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION
For Safety
iii
CAUTION
Always take the following anti-static measures to prevent the internal
circuit from being damaged when using this equipment.
- Wear a wrist strap connected to the ground terminal of this
equipment.
- Connect the ground wires of this equipment, external measuring
instruments and DUT before connecting a coaxial cable.
- Eliminate static electricity charged between the cores and outer
conductors of an external device and the coaxial cable, before
connecting this equipment and the external device.
This equipment is designed for an industrial environment.
In a residential environment, this equipment may cause radio
interference in which case the user may be required to take adequate
measures.
Exposure to corrosive gases such as hydrogen sulfide, sulfurous acid,
and hydrogen chloride will cause faults and failures.
Note that some organic solvents release corrosive gases.
Use in a
Residential
E
nvironment
Use in
Corrosive
Atmospheres
Static Sensitive
iv
Anritsu Warranty
Anritsu Corporation provides the following warranty against stoppages arising
due to manufacturing error, and against problems with operation occurring
even though the procedures outlined in the operation manual were followed.
The equipment is warranted for one year from delivery and will be replaced
free of charge only once under warranty.
After the expiration of one-year warranty period, replacement will not be made
on the failed equipment. Please consider purchasing a new one.
The hardware and software warranties are not valid under any of the following
conditions:
●The fault is due to mishandling, misuse, or unauthorized modification or
repair of the equipment by the customer.
●The fault is due to severe usage clearly exceeding normal usage.
●The fault is due to improper or insufficient maintenance by the customer.
●The fault is due to natural disaster, including fire, wind or flood,
earthquake, lightning strike, or volcanic ash, etc.
●The fault is due to damage caused by acts of destruction, including civil
disturbance, riot, or war, etc.
●The fault is due to explosion, accident, or breakdown of any other
machinery, facility, or plant, etc.
●The fault is due to use of non-specified peripheral or applied equipment
or parts, or consumables, etc.
●The fault is due to use of a non-specified power supply or in a non-
specified installation location.
●The fault is due to use in unusual environments(Note).
●The fault is due to activities or ingress of living organisms, such as
insects, spiders, fungus, pollen, or seeds.
In addition, this warranty is valid only for the original equipment purchaser. It
is not transferable if the equipment is resold.
Anritsu Corporation shall assume no liability for damage or financial loss of
the customer due to the use of or a failure to use this equipment, unless the
damage or loss is caused due to Anritsu Corporation’s intentional or gross
negligence.
Note:
For the purpose of this Warranty, "unusual environments" means use:
●In places of direct sunlight
●In dusty places
●In liquids, such as water, oil, or organic solvents, and medical fluids, or
places where these liquids may adhere
v
●In salty air or in place chemically active gases (sulfur dioxide, hydrogen
sulfide, chlorine, ammonia, nitrogen dioxide, or hydrogen chloride etc.)
are present
●In places where high-intensity static electric charges or electromagnetic
fields are present
●In places where abnormal power voltages (high or low) or instantaneous
power failures occur
●In places where condensation occurs
●In the presence of lubricating oil mists
●In places at an altitude of more than 2,000 m
●In the presence of frequent vibration or mechanical shock, such as in
cars, ships, or airplanes
Anritsu Corporation Contact
In the event of this equipment malfunctions, please contact an Anritsu Service
and Sales office. Contact information can be found on the last page of the
printed version of this manual, and is available in a separate file on the PDF
version.
vi
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re
-export from your
country.
Before re
-exporting the product or manuals, please contact us to confirm
whether they are
export-controlled items or not.
When you dispose of export
-
controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military
purpose.
vii
China RoHS
产品中有害物质的名称及含量
部件名称 有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
[Cr(Ⅵ)]
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷线路板
(PCA)
×
○
××○○
机壳、支架
(Chassis)
×
○××○○
电缆、风扇、连接
器等
(Appended goods)
×○××○○
本表格依据 SJ/T 11364 的规定编制。
○：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以
下。
×：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量
要求。
环保使用期限
这个标记是根据「电器电子产品有害物质限制使用管理办法」以及 SJ/T
11364「电子电气产品有害物质限制使用标识要求」的规定，适用于在中国销
售的电基础上，从生产日起算的该年限内，不会因产品所含有害物质的泄漏或
突发性变异，而对环境污染，人身及财产产生深刻地影响。
viii
I
About This Manual
This operation manual explains the configuration, connection, and
operation of the G0430A PCIe5 Re-Driver Set.
II.
Table of Contents
For Safety .......................................................... iii
About This Manual................................................ I
Configuration of PCIe5 Re-Driver Set1
Connection Procedure..................... 2
2.1 Installation........................................................................ 2
2.2 Cables.............................................................................. 2
Software Operation .......................... 4
3.1 Preparation ...................................................................... 4
3.2 How to Optimize Return Path .......................................... 6
Appendix A Recommended Channel Control
Values ............................................A-1
Andere Handbücher für G0430A
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Anritsu Messgerät Handbücher
Anritsu
Anritsu MU196060A Bedienungsanleitung
Anritsu
Anritsu MS46122A/B-010 Bedienungsanleitung
Anritsu
Anritsu MS2830A Bedienungsanleitung
Anritsu
Anritsu Field Master Pro MS2090A Bedienungsanleitung
Anritsu
Anritsu VNA Master MS2026C Bedienungsanleitung
Anritsu
Anritsu 54100A Series Montage- und Bedienungsanleitung
Anritsu
Anritsu MS2711B Bedienungsanleitung
Anritsu
Anritsu Network Data Analyzer MD6430A Bedienungsanleitung
Anritsu
Anritsu S331E Bedienungsanleitung
Anritsu
Anritsu MU104014B Bedienungsanleitung
Anritsu
Anritsu MS2690A Bedienungsanleitung
Anritsu
Anritsu MP1800A Bedienungsanleitung
Anritsu
Anritsu Microwave Site Master S820E Bedienungsanleitung
Anritsu
Anritsu Series MS278XB Bedienungsanleitung
Anritsu
Anritsu MT1000A Network Master Pro Bedienungsanleitung
Anritsu
Anritsu MP1800A Bedienungsanleitung
Anritsu
Anritsu MT8820A Bedienungsanleitung
Anritsu
Anritsu Site Master S120A Bedienungsanleitung
Anritsu
Anritsu MS2722C Bedienungsanleitung
Anritsu
Anritsu Field Master Pro MS2090A Betriebsanleitung
