Anritsu MS2024A Gebrauchs- und Pflegehandbuch

Is there a problem updating firmware using USB interface?

An intermittent problem occurs with firmware updates using the USB interface with several of the

hand held test instruments. The list of instruments includes the MS2024A, MS2026A, MS2034,

MS2036A, MS2717A/B, MS2718B, MS2719B, MS2721A/B, MS2723B, MS2724B, MS8911A/B,

MT8220A and MT8222A. After the update is completed, the instrument may fail to boot properly.

If you have an instrument that fails to boot after a failed firmware update, use the following steps

to resolve the problem.

1. Close Master Software Tools and then re-open it.

2. Power off the instrument. Connect it via Ethernet to your local network or directly to your

PC using an Ethernet cross-over cable.

3. Power up the instrument into bootstrap mode. Hold the 1st, 3rd and 5th soft keys,

located right of the display directly below the "Esc" key, then press the Power button.

Keep the 3 soft keys pressed until the Anritsu logo appears on the display. The Bootstrap

screen will appear after a few seconds.

4. Press the Ethernet Configuration soft key.

•If your instrument is configured for DHCP, it will immediately attempt to obtain

(lease) an IP address from the network DHCP server and display it at the bottom

left hand corner of the screen. If successful, note and write down the address,

press the Back soft key and go to step #7.

•If the test instrument cannot obtain an IP address from the DHCP server, it will

time out in approximately after 3 minutes. The statement “DCHP Lease Failed”

will be displayed at the bottom left hand corner of the screen. Go to Step 4a,

DHCP Mode 2nd Attempt.

•If your instrument is configured for STATIC IP, it will open to the Static IP

configuration window displaying the current Static IP address at the bottom left

hand corner of the screen. To reconfigure the Static IP address, go to Step 4b,

Static Address Mode.

a. DHCP Mode 2nd Attempt

i. Press the 1st soft key. (No text describes it.) The Static IP configuration

window opens.

ii. Confirm that the connections, the Ethernet line and communication on

the LAN to the test instrument are OK.

iii. Re-attempt to obtain an IP address through DHCP configuration. Press

the 1st soft key, Toggle the address mode (DHCP/Static), to switch to

DHCP configuration and automatically obtain an IP address. Note the IP

address assigned to the instrument.

iv. Press the Back soft key. Return to the main bootstrap screen and go to

Step #5.

b. Static Address Mode

i. Press the 2nd soft key. Enter the IP address.

ii. Press the 3rd soft key. Enter the gateway address.

iii. Press the 4th soft key. Enter the subnet mask.

iv. Attach the Ethernet cross-over cable between the test instrument and

your PC.

v. Press the Back soft key, to return to the main bootstrap screen.

5. Press the Update OS (Ethernet) soft key. The unit should give you a "Waiting for OS

download connection…" message.

6. In Master Software Tools, go to the Tools menu and click Product Updates.

7. The Product Updates window opens. At this point, Master Software Tools is not

connected to your instrument.

8. Highlight the firmware you wish to load into your instrument. If its status is “Ready” the

file is located on the PC and the Emergency Repair button is active. If the file status is

listed as “Available”, click on the Retrieve File button to download the file from the

Anritsu website to your PC. Once the file has been downloaded, its status will be

changed to Ready. Highlight that file.

Note: For Files Not Listed

If the file you are looking for is not on the list –

a. Click the Check for Updates button to obtain the latest list from the Anritsu

website. This will update the Products Updates Screen.

If a zip file was sent to you from Anritsu Company –

a. Copy it to the MST folder. (Default location is C:\Program Files\Anritsu\Anritsu

Master Software Tools\Archives )

b. Select the box next to Show Obsolete Files at the bottom of the Product

Updates screen. This updates the list.

9. Click the Emergency Repair button. The OS Recovery window will open.

10. Click the Ethernet button.

a. Enter the IP address of the instrument.

b. Click the Install New OS Now button. Master Software Tools will connect to your

instrument and proceed to install the firmware. Progress messages will appear

above the buttons. Be patient, the installation can take many minutes.

11. When it is done loading the new OS firmware, the instrument should automatically

reboot. If it does not re-boot, power the instrument off then on. The instrument should

start up normally.

Andere Handbücher für MS2024A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Anritsu Messgerät Handbücher

Anritsu

Anritsu Network Master MT9090A Series Bedienungsanleitung

Anritsu

Anritsu MT8220A Bedienungsanleitung

Anritsu

Anritsu MT8820A Bedienungsanleitung

Anritsu

Anritsu Network Master Series Bedienungsanleitung

Anritsu

Anritsu MS2690A Installationshandbuch

Anritsu

Anritsu MS9740A Bedienungsanleitung

Anritsu

Anritsu Site Master Bedienungsanleitung

Anritsu

Anritsu MS2690A Bedienungsanleitung

Anritsu

Anritsu 56100A Betriebsanleitung

Anritsu

Anritsu VectorStar ME7838AX Bedienungsanleitung

Anritsu

Anritsu Site Master S331C Bedienungsanleitung

Anritsu

Anritsu Site Master S331L Betriebsanleitung

Anritsu

Anritsu Site Master S331L Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7848A Series Bedienungsanleitung

Anritsu

Anritsu MS462 Series Bedienungsanleitung

Anritsu

Anritsu MS2722C Bedienungsanleitung

Anritsu

Anritsu MW9076 Series Bedienungsanleitung

Anritsu

Anritsu 3GPP Bedienungsanleitung

Anritsu

Anritsu Field Master Pro MS2090A Bedienungsanleitung

Anritsu

Anritsu ms2602a Bedienungsanleitung

Anritsu

Anritsu MU196060A Bedienungsanleitung

Anritsu

Anritsu MS2711B Bedienungsanleitung

Anritsu

Anritsu LMR Master S412E Bedienungsanleitung

Anritsu

Anritsu Field Master Pro MS2090A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung