Anritsu MS9710C Bedienungsanleitung

Remote Control

Read this manual before using the equipment. Keep this manual with the equipment.

Optical Spectrum Analyzer

Operation Manual

MS9710C

MS9710C Optical Spectrum Analyzer Remote Control Operation Manual

ANRITSU CORPORATION

Printed in Japan

Document No.: M–W1580AE

5-10-27, Minamiazabu, Minato-ku, Tokyo 106-8570 Japan / Phone: 81-3-3446-1111

Third Edition

MS9710C

Optical Spectrum Analyzer

Remote Control

Operation Manual

Measuring Instruments Division

Measurement Group

ANRITSU CORPORATION

Document No.: M-W1580AE-3.0

To ensure that the MS9710C Optical Spec-

trum Analyzer is used safely, read the

safety information in the MS9710C Optical

Spectrum Analyzer Operation Manual first.

Keep this manual with the Optical Spectrum

Analyzer.

MS9710C

Optical Spectrum Analyzer Remote Control

Operation Manual

14 February 1999(First Edition)

21 April 2000(Third Edition)

the publisher.

The contents of this manual may be changed without prior notice.

Appendix

About This Manual

This manual explains remote control of the MS9710C optical spectrum analyzer.

You can control the MS9710C and transfer measurement results into the

computer connected to the GPIB/RS-232C interface port of the MS9710C.

Table of Contents

For Safety ...................................................iii

About This Manual ........................................ I

Section 1 Introduction.................................. 1-1

1.1 Overview.................................................................... 1-2

1.2 MS9710C Remove Control Functions ....................... 1-2

1.3 Interface Port Application Selection Function ............ 1-2

1.4 Examples of Setups Using GPIB/RS-232C ............... 1-3

Section 2 How to Connect ........................... 2-1

2.1 Connecting Devices Using GPIB Cables................... 2-2

2.2 Connecting a Device Using an RS-232C Cable ....... 2-3

Section 3 Standards ..................................... 3-1

3.1 GPIB Standard........................................................... 3-2

3.2 RS-232C Standard .................................................... 3-2

3.3 Device Message List.................................................. 3-3

Section 4 Initial Setting ................................ 4-1

4.1 Initialization of Bus by IFC Statement........................ 4-4

4.2 Initialization of Message Exchange by DCL and SDC Bus

Commands ................................................................ 4-6

4.3 Initialization of Devices by ∗RST Command.............. 4-8

4.4 Device States at Power-on ........................................ 4-13

Section 5 Listner Input Formats.................. 5-1

5.1 Summary of Listener Input Program Message Syntactical

Notation ..................................................................... 5-3

5.2 Program Message Functional Elements.................... 5-8

5.3 Program Data Format ................................................ 5-20

III

Appendix

Section 6 Talker Output Format .................. 6-1

6.1 Differences in Syntax between Listener Input Formats

and Talker Output formats ......................................... 6-3

6.2 Response Message Functional Elements ................. 6-4

Section 7 Common Commands................... 7-1

7.1 Classification of MS9710C-Supported Common Commands

by Group Function ..................................................... 7-2

7.2 Classification of Supported Commands and

References ................................................................ 7-2

Section 8 Status Structure ........................... 8-1

8.1 IEEE 488.2 Standard Status Model ........................... 8-3

8.2 Status Byte (STB) Register........................................ 8-5

8.3 Enabling the SRQ ...................................................... 8-10

8.4 Standard Event Status Register ................................ 8-12

8.5 Extended Event Status Register................................ 8-15

8.6 Queue Model ............................................................. 8-19

Section 9 Details on Device Messages....... 9-1

Section 10 Program Examples .................... 10-1

10.1 Precautions on Creating a Program .......................... 10-2

10.2 Program Examples .................................................... 10-3

Section 11 LabVIEW Measuring Instrument 11-1

About LabVIEW ................................................................. 11-2

11.1 Installation.................................................................. 11-2

11.2 Program Examples .................................................... 11-3

11.3 List of Measuring Instrument Drivers......................... 11-5

11.4 Description of Measuring Instrument Driver

Functions ................................................................... 11-9

IV.

Appendix A Error Messages ........................ A-1

A.1 System Errors (000 to 099)........................................ A-2

A.2 Measurement Errors (100 to 199).............................. A-2

A.3 Key Operation Errors (200 to 299)............................. A-3

A.4 Device Errors (300 to 499)......................................... A-5

Appendix B Binary Data Transfer Formats... B-1

Appendix C Comparison Table of GPIB

Commands of Controller ......... C-1

Appendix D Example of Program Used on

PC9801 ...................................... D-1

Appendix E MS9710C and MV02 (MS9703A)

Command Compatibility Table .... E-1

Appendix F MS9710C and HP Optical Spectrum

Analyzer (HP71450A/71451A) Com-

mand Compatibility Table........ F-1

1-1

Introduction

111

This section outlines the remote control functions of the MS9710C optical spec-

trum analyzer.

1.1 Overview........................................................ 1-2

1.2 MS9710C Remove Control Functions ........... 1-2

1.3 Interface Port Application Selection Function .. 1-2

1.4 Examples of Setups Using GPIB/RS-232C ... 1-3

Section 1 Introduction

Inhaltsverzeichnis

Andere Anritsu Messgerät Handbücher

Anritsu

Anritsu Spectrum Master Bedienungsanleitung

Anritsu

Anritsu MS2711B Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7838G4 Bedienungsanleitung

Anritsu

Anritsu ML2437A Betriebsanleitung

Anritsu

Anritsu MT8802A Bedienungsanleitung

Anritsu

Anritsu ShockLine MS46131A-020 Bedienungsanleitung

Anritsu

Anritsu Lightning 37 E Series Bedienungsanleitung

Anritsu

Anritsu 37 D Series Bedienungsanleitung

Anritsu

Anritsu Field Master Pro MS2090A Bedienungsanleitung

Anritsu

Anritsu MS2711A Bedienungsanleitung

Anritsu

Anritsu ML2480B Series Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Anritsu

Anritsu Microwave Site Master S820E Bedienungsanleitung

Anritsu

Anritsu MT8820C Bedienungsanleitung

Anritsu

Anritsu S331E Bedienungsanleitung

Anritsu

Anritsu VNA Master MS2026C Betriebsanleitung

Anritsu

Anritsu Field Master Pro Bedienungsanleitung

Anritsu

Anritsu Bit Master MP1026B Betriebsanleitung

Anritsu

Anritsu 56100A Betriebsanleitung

Anritsu

Anritsu MT8801C Bedienungsanleitung

Anritsu

Anritsu Field Master Pro MS2090A Bedienungsanleitung

Anritsu

Anritsu ShockLine ME7868A Bedienungsanleitung

Anritsu

Anritsu MX269018A Bedienungsanleitung

Anritsu

Anritsu PIM Master MW8208A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung