Antari FT-50 Bedienungsanleitung

FT-50 Fire Training

Fog Machine User Manual

ENGLISH

User Manual - English

Safety Information

Please read the following safety information carefully before operating the

machine. This information includes important safeguards about installation,

usage, and maintenance. Pay attention to all warning labels and instructions in

this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

․Keep this device dry.

․Always connect to a grounded circuit to avoid risk of electrocution.

․Before connecting machine to power, always check voltage indicate on machine match

to your local AC voltage. Do not use the machine if AC power voltage does not match.

․Disconnect the machine from AC power before servicing and when not in use.

․This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,

disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts,

immediately unplug the machine and contact your local Antari dealer for advice.

․No user serviceable and modifiable parts inside. Never try to repair this product, an

unauthorized technician may cause damage or malfunction to the machine.

․For adult use only. Never leave the machine running unattended.

․Installed the machine in a well-ventilated area. Provide at least 50 cm space around the

machine.

․Never add flammable liquid of any kind to the machine.

․Make sure there are no flammable materials close to the machine while operating.

․Only use Antari aerosols. Other aerosols may lead to heater clog and malfunction.

․Remove aerosols after use.

․If the machine fails to work, unplug the machine and stop operation immediately.

Contact your localAntari dealer for advise.

․Before transporting the machine, make sure the aerosols is removed

․Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely.

In case of eye contact or if fluid is swallowed, immediately look for medical advice.

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to

ensure that all parts are present and have been received in good condition. If any parts

appear damaged or mishandled from shipping, notify the shipper immediately and retrain the

packing material for inspection.

What is included: 1 x FT-50 Fog Machine

1 x Power Cord

1 x User Manual

Product Dimensions

346 mm

251 mm

152 mm

Product Overview

Operation

Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm

open space around the machine.

Step 2: Check and cleared any foreign object in the threaded aerosol insert. Align aerosol

valve with threaded insert and carefully turn clockwise to fix into positiion. Aerosol should be

screwed in tightly to create an effective seal

Volume Control Knob

Power Switch

LED Indicator

Breaker

Power Input

Aerosol Compartment

Step 3: Connect the machine to suitable rated power supply. To determine the power

requirement for the machine refer to the label on the back of the machine.

Always connect the machine to a protected circuit and ensure it is properly

grounded to avoid risk of electrocution.

Step 4: Turn on the machine and allow it to heat up. Heat up takes approximatly 7.5 mintues.

Once the machine has reached operating temperature, the LED inidcator located in back

panel will turn solid green. Now the machine is ready for operation.

Step 5: To start making fog, press and hold the push button on handle bar, release to stop.

Step 6: To adjust output volume, rotate the knob located in back panel. Turn

counter-clockwise to increase, clockwise to decrease.

Step 7: To turn off the machine, flip the power switch to OFF position. Remove aerosol and

power cord.

Off Power Operation

FT-50 can be operating off mains power once it has reached working temperature. The

amount of smoke can be produced depends on its temperature cycle when it is

disconnected. With a complete heating cycle the machine can still generate smoke up to 45

minutes after disconnection.

The quality of fog must be carefully observed while operating off mains power. When smoke

has become thin and blue indicates the temperature is getting low. Reconnect machine to

mains power for heating process, once it reached working temperature it can be operate off

power again.

Aerosols

Only use Antari FLP-700 aerosol for the FT-50 Fire Training Fog

Machine.

The machine is tested and calibrated with this aerosol to get the

best output performance. Warranty will be void if any other type

of aerosol is used, improper use of aerosol may lead to

machine failure and malfunction.

Service and Maintenance

․Do not allow the machine to become contaminated.

․Remove dust from air vents with air compressor, vacuum or a soft brush.

․Only use a damp cloth to clean the casing.

․Before storing run distilled water through the system to help avoid condensing the pump

or heater.

․It is recommended to run the machine on a monthly basis in order to achieve best

performance and output condition.

․Excessive dust, liquid and dirt built up will degrade performance and cause overheating.

Breaker Reset

Disconnect AC power before resetting the breaker. Only replace fuse with same

type and rating.

Step 1: Disconnect AC power.

Step 2: Flip breaker to ON position.

Step 3: Turn on machine for testing.

Breaker

120V = 15A 250V

230V = 8A 250V

Technical Specifications

Input voltage US 120V EU 230V

UK 240V JP 100V

Breaker 120V = 15A 250V

230V = 8A 250V

Heater 1450W

Warm-up time 7.5 min. (approx.)

Fluid consumption 110 ml/min

Compatible fluid Antari FLP aerosol

Power connection IEC

Dimension L 346 x W 152 x H 251 mm

Dry weight 9.8 kg

Andere Handbücher für FT-50

Inhaltsverzeichnis

Andere Antari Nebelmaschine Handbücher

Antari

Antari X-510PRO Bedienungsanleitung

Antari

Antari B-100X Bedienungsanleitung

Antari

Antari M-7 RGBA Bedienungsanleitung

Antari

Antari M-9 RGBAW Bedienungsanleitung

Antari

Antari HZ-100 Bedienungsanleitung

Antari

Antari WiFi-800 Bedienungsanleitung

Antari

Antari Z-1500 III Bedienungsanleitung

Antari

Antari M-1 Bedienungsanleitung

Antari

Antari Z-1500II Bedienungsanleitung

Antari

Antari Z-380 Bedienungsanleitung

Antari

Antari F-80Z Bedienungsanleitung

Antari

Antari B-100 Bedienungsanleitung

Antari

Antari F-4 Fazer Bedienungsanleitung

Antari

Antari FT-200 Bedienungsanleitung

Antari

Antari M-4 Bedienungsanleitung

Antari

Antari Z-Stream Bedienungsanleitung

Antari

Antari HZ-350 Bedienungsanleitung

Antari

Antari Z-80 Bedienungsanleitung

Antari

Antari F-6 Bedienungsanleitung

Antari

Antari Z-380 Bedienungsanleitung

Antari

Antari M-11 Bedienungsanleitung

Antari

Antari F-450 Bedienungsanleitung

Antari

Antari Mobile MB-20 Bedienungsanleitung

Antari

Antari DNG-200 Bedienungsanleitung

Beliebte Nebelmaschine Handbücher anderer Marken

Boost

Boost BOOST-FOG400LED-BK Bedienungsanleitung

Home Accents Holiday

Home Accents Holiday FM1000-ASH Bedienungsanleitung

EuroLite

EuroLite ZEITGEIST FOG-1200 Bedienungsanleitung

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Bedienungsanleitung

PROEL

PROEL DRAGO HEAVY PLFD150HY Bedienungsanleitung

Sparklyn

Sparklyn Y846 Bedienungsanleitung

Magicfx

Magicfx CO2 Gun Bedienungsanleitung

Ibiza

Ibiza LSM500LAS Bedienungsanleitung

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Bedienungsanleitung

High End

High End F-100 Bedienungsanleitung

Chauvet

Chauvet ARENA 2100 FLEX Bedienungsanleitung

Beamz

Beamz F1600 Bedienungsanleitung

Sagitter

Sagitter SG ARS900C Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-STF-480 Bedienungsanleitung

Orion

Orion OT-U250PP Leitfaden

Beamz

Beamz S2500 Bedienungsanleitung

American DJ

American DJ Dyno-Fog II Bedienungsanleitung

JB Systems

JB Systems FX 1700 Bedienungsanleitung