Antari FT-55 Bedienungsanleitung
1
FT-55 Fire Training
Fog Machine User Manual
English
©2018 Antari Lighting and Effects Ltd.
3
User Manual - English
Safety Information
Please read the following safety information carefully before operating the
machine. This information includes important safeguards about installation,
usage, and maintenance. Pay attention to all warning labels and instructions in
this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact your local
Antari dealer for help.
․Keep this device dry.
․Always connect to a grounded circuit to avoid risk of electrocution.
․Before connecting machine to power, always check the voltage indicated on machine
matches to your local AC voltage. Do not use the machine if the AC power voltage does
not match.
․Disconnect the machine from AC power before servicing and when not in use.
․This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,
disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts,
immediately unplug the machine and contact your local Antari dealer for advice.
․No user serviceable and modifiable parts inside. Never try to repair this product, an
unauthorized technician may cause damage or malfunction to the machine.
․For adult use only. Never leave the machine running unattended.
․Install the machine in a well-ventilated area. Provide at least 50 cm of space around the
machine.
․Never add flammable liquid of any kind to the machine.
․Make sure there are no flammable materials close to the machine while operating.
․Only use Antari aerosols. Other aerosols may lead to heater clog and malfunction.
․Remove aerosols after use.
4
․If the machine fails to work, unplug the machine and stop operation immediately.
Contact your local Antari dealer for advice.
․Before transporting the machine, make sure the aerosols is removed
․Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely.
In case of eye contact or if fluid is swallowed, immediately look for medical advice.
Unpacking and Inspection
Immediately upon receiving the machine, carefully unpack the carton, check the content to
ensure that all parts are present and have been received in good condition. If any parts
appear damaged or mishandled from shipping, notify the shipper immediately and retain the
packing material for inspection.
What is included: 1 x FT-55 Fog Machine
1 x Power Cord
1 x FC-1 Remote Control
1 x User Manual
Product Dimensions
346 mm
251 mm
152 mm
5
Product Overview
Operation
Step 1: Place the machine on a flat surface and in a suitably large area with at least 50 cm
open space around the machine.
Step 2: Ensure that there are not any foreign objects in the threaded aerosol insert. Align
aerosol valve with threaded insert and carefully turn clockwise to fix into position. Aerosol
should be screwed in tightly to create an effective seal
Step 3: Connect the machine to a suitably rated power supply. To determine the power
Volume Control Knob
Power Switch
LED Indicator
Breaker
Power Input
Aerosol Compartment
Wire Remote Socket
6
requirement for the machine refer to the label on the back of the machine.
Always connect the machine to a protected circuit and ensure it is properly
grounded to avoid risk of electrocution.
Step 4: Turn on the machine and allow it to heat up. Heat up takes approximatly 7.5 mintues.
Once the machine has reached operating temperature, the LED inidcator located in the back
panel will turn solid green. Now the machine is ready for operation.
Step 5: To start making fog, press and hold the push button on handle bar, release to stop.
Step 6: To adjust output volume, rotate the knob located in back panel. Turn
counter-clockwise to increase, clockwise to decrease.
Step 7: To turn off the machine, flip the power switch to OFF position. Remove aerosol and
power cord.
FC-1 Remote Control Operation
To operate the machine by remote control, connect the remote to the rear of machine. Press
and hold the button to activate, release button to stop.
Note: Remote control operation only available when the machine is connected to a main
power source.
7
FCR-1 Wireless Operation (Optional)
To operate the machine by wirless remote control, first connect the receiver to the rear of
machine. Press and hold the button on the transmiiter to activate smoke, release to stop.
Note: Wireless operation only available when machine connected to a power source.
Off Power Operation
FT-55 can operate plugged in once it has reached working temperature. The amount of
smoke produced depends on its temperature cycle when it is disconnected. With a complete
heating cycle the machine can generate smoke up to 45 minutes after disconnection.
The quality of fog must be carefully observed while operating disconnected to a main power
source. When smoke has become thin and blue indicates the temperature is getting low.
Reconnect machine to a main power source for heating process, once it has reached
working temperature it can be operated off disconnected again.
FT-55 might eject fluid when working temperature is not reached.
8
Aerosols
Only use Antari FLP-700 aerosol for the FT-55 Fire Training
Fog Machine.
The machine is tested and calibrated with this aerosol to get the
best output performance. Warranty will be voided if any other
type of aerosol is used, improper use of aerosol may lead to
machine failure or malfunction.
Service and Maintenance
․Do not allow the machine to become contaminated.
․Remove dust from air vents with air compressor, vacuum or a soft brush.
․Only use a damp cloth to clean the casing.
․Before storing run distilled water through the system to help avoid condensing the pump
or heater.
․It is recommended to run the machine on a monthly basis in order to achieve best
performance and output condition.
․Excessive dust, liquid and dirt built up will degrade performance and cause overheating.
Breaker Reset
Disconnect AC power before resetting the breaker. Only replace fuse with same
type and rating.
Step 1: Disconnect AC power.
Step 2: Flip breaker to ON position.
Step 3: Turn on machine for testing.
9
Breaker
120V = 15A 250V
230V = 8A 250V
Technical Specifications
Input voltage
Rated power
Warm-up time
Fluid consumption
Compatible fluid
Ambient temp. range
Output
Control
Connection
Optional accessories
Dimension
Weight
US model : AC 100-120V, 50 / 60Hz 15A
EU model : AC 220-240V, 50 / 60Hz 8A
1450W
7.5 minutes (approx.)
110 ml/min
Antari FLP aerosol
0 °C - 40 °C (32 °F-104 °F)
20,000 ft3/min (566 m3/min)
Manual
Wireless (Optional)
IEC (Power)
FCR-1 Wireless Remote
L346 W152 H251 mm
(L13.62 W5.98 H9.88 inch)
10.2 kg (22.49 lbs)
Inhaltsverzeichnis
Andere Antari Nebelmaschine Handbücher
Antari
Antari M-7 RGBA Bedienungsanleitung
Antari
Antari F-80Z Bedienungsanleitung
Antari
Antari HZ-500 Bedienungsanleitung
Antari
Antari HZ-350 Bedienungsanleitung
Antari
Antari FT-20 Bedienungsanleitung
Antari
Antari X-510PRO Bedienungsanleitung
Antari
Antari Z-1000X MK3 Bedienungsanleitung
Antari
Antari Z-1520 RGB Bedienungsanleitung
Antari
Antari SW-250 Bedienungsanleitung
Antari
Antari F-5D Fazer Bedienungsanleitung
Antari
Antari F-80ZY Bedienungsanleitung
Antari
Antari Z-800II Bedienungsanleitung
Antari
Antari M-7 RGBA Bedienungsanleitung
Antari
Antari Z-3000II Bedienungsanleitung
Antari
Antari MOBILE MB-1 Bedienungsanleitung
Antari
Antari LCU-1 Bedienungsanleitung
Antari
Antari Z-800II Bedienungsanleitung
Antari
Antari HZ-100 Bedienungsanleitung
Antari
Antari M-11 Bedienungsanleitung
Antari
Antari AF-5X Bedienungsanleitung
Beliebte Nebelmaschine Handbücher anderer Marken
Boost
Boost BOOST-FOG400LED-BK Bedienungsanleitung
Home Accents Holiday
Home Accents Holiday FM1000-ASH Bedienungsanleitung
EuroLite
EuroLite ZEITGEIST FOG-1200 Bedienungsanleitung
Dyna-Fog
Dyna-Fog CYCLONE ULTRA 2734 Bedienungsanleitung
PROEL
PROEL DRAGO HEAVY PLFD150HY Bedienungsanleitung
Sparklyn
Sparklyn Y846 Bedienungsanleitung
