AOpen S760GXm-SL Datenblatt

AGP 8X Expansion Slot that

supports 8X AGP card(2.1GB/s)

SiS 760GX/SiS 964 Chipsets

(s760GXm-SL/s760GXm-S)

JP28 PS2 KB/Mouse Wakeup

Jumper

IrDA Connector

754-pin CPU Socket with

Voltage and Frequency

Auto-Detection that supports

AMD® AthlonTM 64 CPU

CPUFAN Connector

Onboard AC’97 CODEC

AUX

IN Connector

32-bit PCI Expansion Slots x3

SYSFAN1 Connector

JP14 CMOS Data Clear Jumper Low ESR Capacitors

S/PDIF Connector

IN Connector

AOpen reserves the right to revise all the specifications and information contained in this document, which are subject to change without notice.

STBY LED

Front Audio Connector

USB 2.0 Connectors x2

Front Panel Connector

Case Open Connector

Serial ATA Connectors x2

Supports 150 MB/s Transfer Rate

(s760GXm-SL/s760GXm-S)

FDD Connector

SYSFAN2 Connector

ATX Power Connector

RealTek Gigabit LAN chip

(for s760GXm-SL)

RealTek 10/100Mbps LAN chip

(for s760GXm-S/s760GXm)

AGP Protection LED

s760GXm-SL / s760GXm-S / s760GXm

184-pin DIMMsx2

support DDR400/333/266

Max. To 2GB

IDE Connectors x 2

(ATA 66/100/133 supported)

Speaker

Out

PS/2 Mouse

Connector SPP/EPP/ECP Parallel Port

USB 2.0

Ports

RJ45 10/100/1000

LAN Jack

PS/2

board USB 2.0 Ports

COM 1 Port VGA Port

Line-In

MIC-In

4-pin ATX Power Connector

COM2 Connector

DieHard BIOS Lite SiS 760GX/SiS 964L Chipsets

(s760GXm)

Easy Installation Guide x 1

80-Wire ATA 133 Cable x 1

Floppy Drive Cable x 1

Bonus Pack CD x 1

I/O Shield x 1

SiS 964 Serial ATA RAID Driver Disk x 1

(for s760GXm-SL/s760GXm-S only)

Serial ATA Cable x 1

(for s760GXm-SL/s760GXm-S only)

Serial ATA Power Cable x 1

(for s760GXm-SL/s760GXm-S only)

PART NO:

DOC. NO: S760GXMSL-EG-E0410B

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in

the Bonus Pack CD. Thanks for

the help of saving our earth.

1. Installing CPU

2. Installing CPU Fan

& System Fan

3. Installing

Memory Module

4. Installing HD,

CD-ROM and SATA

Disk

etc

6. Connecting ATX

Power Cable

5. Connecting Front

Panel Cable

7. Installing AGP & PCI Cards

8. Installing Other Devices

(USB, Front Audio, etc)

9. Connecting Back

Panel Ports

(Keyboard, Mouse,

etc)

10. Loading Default

BIOS, Setting CPU

Frequency

11. Installing Operating

System (such as,

Windows XP)

12. Installing Drivers & Utilities

This motherboard supports AMD®Athlon 64 Socket 754 CPU. Be careful of CPU

orientation when you plug it into CPU socket.

1. Pull up the CPU socket lever and up

to 90-degree angle.

2. Locate Pin 1 in the socket and look

for a golden arrow on the CPU

upper interface. Match Pin 1 and

golden arrow. Then insert the CPU

into the socket.

3. Press down the CPU socket lever

and finish CPU installation.

Primary

Master (1st)

Primary

Slave (2nd)

Secondary

Slave (4th)

Secondary

Master (3rd)

Pin 1

3. Installing Memory Modules

2. Installing CPU & System Fans

1. Installing CPU

Plug in the CPU fan cable to the 3-pin CPUFAN connector. If you have chassis fan,

you can also plug it in SYSFAN1 or SYSFAN2 connector.

CPUFAN Connector

SYSFAN1 Connector

SYSFAN2 Connector

DIMM slots are designed in black which are very easy to recognize. Insert the

module straight down to the DIMM slot with both hands and press down firmly until

the DIMM module is securely in place.

4. Connecting IDE and Floppy Cables

Connect 34-pin floppy cable and 40-pin, 80-wire IDE cable to floppy connector FDD

and IDE connector. Be careful of the pin1 orientation. Wrong orientation may cause

system damage.

Pin 1

ATA 66/100/133

IDE Connector

IDE 1 (Primary)

IDE 2 (Secondary)

FDD Connector

Note: If you do not

match the CPU socket Pin 1

and CPU cut edge well, you

may damage the CPU.

Note: The tabs of

the DIMM slot will

close-up to hold the

DIMM in place when the

DIMM touches the slot’s

bottom.

Note: Some CPU fans

do not have sensor pin so

they cannot support fan

monitoring.

CPU socket lever

Golden Arrow

Socket Pin 1

Tab

Pin 1

Key

GND

+12V

SENSOR

GND

+12V

SENSOR

GND

+12V

SENSOR

Attach the power LED, speaker, and reset switch connectors to the

corresponding pins. If you enable “Suspend Mode” item in BIOS Setup, the

ACPI & Power LED will keep flashing while the system is in suspend mode.

Locate the power switch cable from your ATX housing. It is 2-pin female

connector from the housing front panel. Plug this connector to the soft-power

switch connector marked SPWR.

After you finish the setting of jumpers and connect correct cables. Power

on and enter the BIOS Setup, press <Del> during POST (Power On Self

Test). Choose "Load Setup Defaults" for recommended optimal

performance.

5. Connecting Front Panel Cable

6. Connecting ATX Power Cables

This motherboard comes with a 20-pin and 4-pin ATX power connector as shown

below. Make sure you plug in the right direction. We strongly recommend you to

insert the 4-pin connector before connecting the 20-pin connector

7. Power-on and Loading BIOS Setup

Del

8. AOpen Bonus Pack CD and EzInstall

You can use the autorun menu of Bonus CD disc. Choose the utility and driver

from the icons at left side, and then click on the “GO” button to complete

installation automatically.

Warning: Please avoid of using "Load Turbo Defaults", unless you are sure your

system components (CPU, RAM, HDD, etc.) are good enough for turbo setting.

Click to install

online manual

Install utility

Browse

Read me

Exit CD

Install driver

Power Switch

Front Panel Connector

GND

Power LED-

GND

Power LED+

GND

RESET

GND

+5V

HDD LED

+5V

GND

SPEAKER

Setting CPU Voltage & Frequency

ett

CPU C

ore

tage

This motherboard supports Voltage ID (VID) function to detect CPU voltage

automatically during power-on.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through

1MHz stepping CPU Overclocking in the BIOS. CPU Core Frequency = CPU FSB

clock x CPU Ratio. However, all CPU now selling in the market belong to "Fixed

Multiplier". That means users can not adjust the CPU Ratio but only change CPU

FSB clock to achieve overclocking.

(Users do the overclocking at their own risk!!)

BIOS Setup > Frequency / Voltage Control > CPU Speed Setup

CPU Ratio From 4x to 25x step 1x

CPU Clock

(Adjustment manually) FSB = 200MHz-250MHz by 1 MHz

Stepping CPU Overclocking

CPU CPU

Core

CPU

Clock L2

Cache Ratio

Athlon 64 2800+ 1800MHz 200MHz 512KB 9x

Athlon 64 3000+ 2000MHz 200MHz 512KB 10x

Athlon 64 3200+ 2000MHz 200MHz 1024KB 10x

Athlon 64 3200+ 2200MHz 200MHz 512KB 11x

Athlon 64 3400+ 2200MHz 200MHz 1024KB 11x

Athlon 64 3400+ 2400MHz 200MHz 512KB 12x

Athlon 64 3700+ 2400MHz 200MHz 1024KB 12x

Note: With CPU speed changing rapidly, there might be faster CPU on

the market by the time you received this installation guide. This table is

kindly for your references only.

JP14 Clear CMOS

JP28 Keyboard/Mouse Wakeup Jumper

This motherboard provides keyboard / mouse wake-up function. You can use JP28

to enable or disable this function, which could resume your system from suspend

mode with keyboard or mouse. The factory default setting is “Disable” (1-2), and

you may enable this function by setting the jumper to 2-3.

You can clear CMOS to restore system default

setting. To clear the CMOS, follow the procedure

below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1

& pin 2.

5. Connect ATX power cable back to connector PWR2.

Pin 1

Note: If your system hangs or fails to boot because of overclocking, simply use

<Home> key to restore the default setting or you can wait the AOpen “Watch Dog ABS”

reset the system in five seconds and system will auto-detect hardware again.

Warning: SiS 760GX chipset supports maximum 800MHz system clock and 66MHz

AGP clock; higher clock setting may cause serious system damage.

Tip: When should I Clear CMOS?

1. Boot fails because of overclocking…

2. Forget password…

3. Troubleshooting…

Normal

(Default) Clear CMOS

1 1

Disable

(Default) Enable

USB 2.0 Connector

This motherboard provides eight USB 2.0 ports to connect USB devices, such as

mouse, keyboard, modem, printer, etc. There are four ports on the back panel.

You can use proper cables to connect the Front USB connector to USB modules or

front panel of chassis.

Pin 1

Gigabit LAN onboard (for s760GXm-SL)

On the strength of Gigabit LAN controller on board, this motherboard provides

10/100/1000 Mbps Ethernet for office and home use (for s760GXm-S / s760GXm,

it is 10/100 Mbps). The Ethernet RJ45 connector is located on top of USB

connectors. The right hand side LED indicates link mode, it lights in yellow

whenever linking to network. The left hand side LED indicates the transfer mode

and it lights in green when data is transferring in 100Mbps (never lights while in

10Mbps), but lights in orange when transferring in Gigabit’s mode. To enable or

disable this function, you may simply adjust it through BIOS.

Transferring (Left)

Green 100Mbps

Orange Gigabit mode

Linking (Right)

Yellow

Front Audio Connector

If the housing is designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please

remove the jumper cap from the Front Audio Connector before you connect the

cable. Do not remove this yellow jumper cap if your housing doesn’t have an audio

port on the front panel.

Pin 1

S/PDIF Connector

S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format,

which provides impressive audio quality through optical fiber and allows you to

enjoy digital audio instead of analog audio. Through a specific audio cable, you can

connect the S/PDIF connector to other end of the S/PDIF audio module, which

bears S/PDIF digital output. Normally there are two S/PDIF outputs as shown, one

for RCA connector, the most common one used for consumer audio products, and

the other for optical connector with better audio quality. Same as outputs, you can

also connect RCA or optical audio products to input connectors on the module and

have the voice or music come out from your computer. However, you must have a

S/PDIF supported speaker/amplifier/decoder with S/PDIF digital input/output to

connect to the S/PDIF digital input/output to make the most out of this function.

S/PDIF IN

(RCA)

S/PDIF Module

(User Upgrade Optional)

S/PDIF

Cable

S/PDIF OUT

S/PDIF IN

(Optical)

S/PDIF OUT Pin 1

Pin 1 +5V

SBD7-

SBD7+

GND

+5V

SBD6-

SBD6+

GND

9 10

USB Connector

1 2

KEY

AUD_GND

AUD_VCC

Front Audio Connecto

AUD_RET_R

AUD_FPOUT_L

AUD

FPOUT

AUD MIC BIAS

AUD

MIC

AUD_RET_L

+5V

KEY

SPDIF OUT

GND

SPDIF IN

Phoenix-Award BIOS ERROR Message

Beep Sound Message

1 short(Beep) System booting is normally.

1 long - 1 short(Beep) DRAM ERROR

1 long - 2 short(Beep) Display card or monitor connected error

1 long - 3 short(Beep) Keyboard Error

Long(Beep) continuous DRAM hasn't inset correctly.

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Phoenix - AwardBIOS v6.00PG, An Energy Star Ally

s760GXm-SL R1.02 July. 01. 2004 AOpen Inc.

Model name and BIOS version

Model name and BIOS version can be found on upper left corner of first boot

screen (POST screen). For example:

S760GXm-SL is model name of motherboard; R1.02 is BIOS version

Thanks for choosing AOpen product, please register this motherboard at

http://club.aopen.com.tw/productreg/ to become a Gold member of Club AOpen,

and to ensure high service quality and priority from AOpen. You will also have a

chance to play slot machine game to win prize from AOpen. Please prepare the

following information before you start: Model Name, Part Number (P/N),

Serial Number (S/N) and Purchase Date. The Part Number and Serial

number are printed on bar code label. You can find this bar code label on the

outside packing or on component side of PCB. For example:

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. We invite you to register at

http://www.aopen.com to become a Gold Member of Club AOpen so as to ensure

quality service in the future. In order to maintain the best service to every

customer of us, we recommend you to follow the procedures below and seek help

from our branches according to the region you buy the product. With your help, we

can then continue to provide efficient and the best quality service to every

customer.

Thanks very much for your understanding!

Europe Email: [email protected]

Pacific Rim http://www.aopen.com.tw/tech/default.htm

China http://www.aopen.com.cn/tech/default.htm

Germany http://www.aopencom.de/tech/default.htm

America http://usa.aopen.com/tech/default.htm

Japan http://aopen.jp/tech/index.html

Europe

AOpen Computer b.v.

Tel: 31-73-645-9516

Email: [email protected]

China

艾爾鵬國際貿易(上海)有限公司

Tel: 86-21-6225-8622 Fax:

86-21-6225-7926

Pacific Rim

AOpen Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5899

America

AOpen America Inc.

Tel: 1-510-489-8928

Fax: 1-510-489-1998

Japan

AOpen Japan Inc.

Tel: 81-048-290-1800

Fax: 81-048-290-1820

Germany

AOpen Computer GmbH.

Tel: 49-2131-1243-710

Fax: 49-2131-1243-999

Andere Handbücher für s760GXm-SL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

AOpen

AOpen i945Ga-PHS Bedienungsanleitung

AOpen

AOpen AK77-400 Einrichtungshandbuch

AOpen

AOpen DX37PU-OL-E0112B Bedienungsanleitung

AOpen

AOpen AX34II Bedienungsanleitung

AOpen

AOpen MX4L Datenblatt

AOpen

AOpen AX6BC PROII Bedienungsanleitung

AOpen

AOpen S661FXm-FSN Bedienungsanleitung

AOpen

AOpen MX4SGI-4DN2 Bedienungsanleitung

AOpen

AOpen AX4T 2-533 Datenblatt

AOpen

AOpen MK33IIA Bedienungsanleitung

AOpen

AOpen i865PEa-7ILFR Datenblatt

AOpen

AOpen Fortress 7000 Bedienungsanleitung

AOpen

AOpen AK77-600 Max Bedienungsanleitung

AOpen

AOpen MX4GVR Einrichtungshandbuch

AOpen

AOpen DX6G Plus Bedienungsanleitung

AOpen

AOpen s661FXm-7US Bedienungsanleitung

AOpen

AOpen AK77-8X Datenblatt

AOpen

AOpen MK77M-8XN Einrichtungshandbuch

AOpen

AOpen AX4T II-133 Bedienungsanleitung

AOpen

AOpen AX4G Pro Datenblatt

AOpen

AOpen i865Gm-I Bedienungsanleitung

AOpen

AOpen MX4BR-533 Einrichtungshandbuch

AOpen

AOpen AX6B Plus Bedienungsanleitung

AOpen

AOpen MX3W-V Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

AOpen s760GXm-SL Datenblatt

Beliebte Hauptplatine Handbücher anderer Marken