Apera Instruments YD300 Gebrauchsanweisung

YD300 Portable Water Hardness Meter

Quick Start Manual

Scan to watch the video tutorial

1. Electrode Activation

a) For first-time use — shake electrode with force to let the inner solution of electrode fall into the measuring head

compartment; there should NOT be any bubbles within the measuring head. Pour a small amount of soaking

solution into the soaking solution vial, and soak the electrode for 30 minutes.

b) Regular Usage — The activation time only takes 10 to 15 minutes for a frequently used electrode. As long as the

reading is stable, users can start to perform calibration and measurements (please note that the readings without

electrode being immersed in solutions are random).

2. Calibration (take B2, B3 calibration and mmol/L as an example)

1) Power on the meter. Press , and icons appear and are flashing at the same time,

indicating the meter enters 1st point calibration; the calibration solution is B2.

2) Rinse the electrode in distilled/deionized water and shake off excess water; insert the electrode into B2

calibration solution and gently stir the electrode for a few seconds and let it stand still; Wait for the reading to

fully stabilize (about 2 minutes).

3) Then press to confirm calibration, “2.00×10-1mmol/L” icon starts flashing (see picture (4-3),

indicating 1st point calibration will be finished after approximately 20 seconds. During the icon flashing, do

NOT press any key.

4) NOTE: The reading may be temporarily stable in about 30 seconds, but we recommend waiting about 2 minutes

for the reading to get fully stabilized before pressing to confirm calibration. This practice will

significantly improve the accuracy of calibration.

5) Then and icons will appear and start flashing, indicating the meter enters 2nd point calibration

mode; the calibration solution is B3.

6) Rinse the electrode in distilled/deionized water and shake off excess water; insert it into B3 calibration solution;

stir the electrode for a few seconds and let it stand still. Wait for the reading to fully stabilize (about 2 minutes).

7) Press button to confirm the 2nd point calibration, “2.00 and mmol/L” icon starts flashing (see picture

(4-4)); calibration will be finished after approximately 20 seconds. During the icon flashing, do NOT press any

key. The meter then returns to measurement mode.

8) To verify the calibration quality: Rinse the electrode in distilled/deionized water and shake off excess water; then

put it into the B2 solution, stir for a few seconds and let it stand still;

Take the reading after appears and stays; The reading should be close to 2.00 ±0.25×10-1 mmol/L.

Otherwise, please repeat the calibration process.

3. Sample Test

Pour your sample solution into the #1 or #2 sample vial (bottle). Rinse electrode with distilled/deionized water and shake

off excess water; insert the probe into sample solution, stir gently and let it stand still; when icon appears and stays,

take the reading. Press to save the measurement data. Press to switch to other units.

4. Parameters Setting

When the meter is powered on and in measurement mode, long press (>2 seconds) to enter parameter setting

mode. Short press to change the parameter; Press to confirm the change and return to measurement

mode.

Prompt

Parameter setting items

Parameter

Calibration Method Setting

--------

Resolution Setting

0.01-0.1

Temperature Unit Setting

℃-℉

Activity Compensation Setting

OFF-On

Backlight Automatically Off Setting

OFF-On

Automatic Power Off

OFF-On

Default Setting

OFF-On

YD300 Portable Water Hardness Meter

Quick Start Manual

Scan to watch the video tutorial

1. Electrode Activation

c) For first-time use — shake electrode with force to let the inner solution of electrode fall into the measuring head

compartment; there should NOT be any bubbles within the measuring head. Pour a small amount of soaking

solution into the soaking solution vial, and soak the electrode for 30 minutes.

d) Regular Usage — The activation time only takes 10 to 15 minutes for a frequently used electrode. As long as the

reading is stable, users can start to perform calibration and measurements (please note that the readings without

electrode being immersed in solutions are random).

2. Calibration (take B2, B3 calibration and mmol/L as an example)

9) Power on the meter. Press , and icons appear and are flashing at the same time, indicating

the meter enters 1st point calibration; the calibration solution is B2.

10) Rinse the electrode in distilled/deionized water and shake off excess water; insert the electrode into B2

calibration solution and gently stir the electrode for a few seconds and let it stand still; Wait for the reading to

fully stabilize (about 2 minutes).

11) Then press to confirm calibration, “2.00×10-1mmol/L” icon starts flashing (see picture (4-3),

indicating 1st point calibration will be finished after approximately 20 seconds. During the icon flashing, do

NOT press any key.

12) NOTE: The reading may be temporarily stable in about 30 seconds, but we recommend waiting about 2 minutes

for the reading to get fully stabilized before pressing to confirm calibration. This practice will

significantly improve the accuracy of calibration.

13) Then and icons will appear and start flashing, indicating the meter enters 2nd point calibration

mode; the calibration solution is B3.

14) Rinse the electrode in distilled/deionized water and shake off excess water; insert it into B3 calibration solution;

stir the electrode for a few seconds and let it stand still. Wait for the reading to fully stabilize (about 2 minutes).

15) Press button to confirm the 2nd point calibration, “2.00 and mmol/L” icon starts flashing (see picture

(4-4)); calibration will be finished after approximately 20 seconds. During the icon flashing, do NOT press any

key. The meter then returns to measurement mode.

16) To verify the calibration quality: Rinse the electrode in distilled/deionized water and shake off excess water; then

put it into the B2 solution, stir for a few seconds and let it stand still;

Take the reading after appears and stays; The reading should be close to 2.00 ±0.25×10-1 mmol/L.

Otherwise, please repeat the calibration process.

3. Sample Test

Pour your sample solution into the #1 or #2 sample vial (bottle). Rinse electrode with distilled/deionized water and shake

off excess water; insert the probe into sample solution, stir gently and let it stand still; when icon appears and stays,

take the reading. Press to save the measurement data. Press to switch to other units.

4. Parameters Setting

When the meter is powered on and in measurement mode, long press (>2 seconds) to enter parameter setting

mode. Short press to change the parameter; Press to confirm the change and return to measurement

mode.

Prompt

Parameter setting items

Parameter

Calibration Method Setting

--------

Resolution Setting

0.01-0.1

Temperature Unit Setting

℃-℉

Activity Compensation Setting

OFF-On

Backlight Automatically Off Setting

OFF-On

Automatic Power Off

OFF-On

Default Setting

OFF-On

Andere Handbücher für YD300

Inhaltsverzeichnis

Andere Apera Instruments Messgerät Handbücher

Apera Instruments

Apera Instruments LabSen 241-3SP Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 861 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 753 Bedienungsanleitung

Apera Instruments

Apera Instruments 201-C Bedienungsanleitung

Apera Instruments

Apera Instruments SX811-PW Bedienungsanleitung

Apera Instruments

Apera Instruments PH910 Bedienungsanleitung

Apera Instruments

Apera Instruments PH850 Bedienungsanleitung

Apera Instruments

Apera Instruments DO8500 Bedienungsanleitung

Apera Instruments

Apera Instruments EC400 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 753 Bedienungsanleitung

Apera Instruments

Apera Instruments SX751 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 763 Bedienungsanleitung

Apera Instruments

Apera Instruments SX716 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 823 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 851-H Bedienungsanleitung

Apera Instruments

Apera Instruments PHB-3 Bedienungsanleitung

Apera Instruments

Apera Instruments 9500 Premium Series Bedienungsanleitung

Apera Instruments

Apera Instruments SX731 Bedienungsanleitung

Apera Instruments

Apera Instruments YD300 Bedienungsanleitung

Apera Instruments

Apera Instruments WS100 Bedienungsanleitung

Apera Instruments

Apera Instruments SX721 Bedienungsanleitung

Apera Instruments

Apera Instruments TN400 Bedienungsanleitung

Apera Instruments

Apera Instruments MP511 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 803 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung