Argo DAKOTA Bedienungsanleitung

V 05/21

DAKOTA

This product is only suitable for well insulated spaces or

occasional use.

OPERATING INSTRUCTIONS

Read the instructions carefully before installing and operating the appliance or performing

maintenance operations. Observe all the safety instructions; failure to observe the instructions may

cause accidents and/or damages. Store these instructions for future reference.

ELECTRIC CONVECTOR HEATER

V 05/21

GENERAL SAFETY INFORMATION

Use this convector only as outlined in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock or

injury to persons.

This convector is designed for domestic use. It must not be used for

commercial or industrial purposes.

Ensure that the mains voltage complies with that indicated on the

convector data plate (220-240V~ 50-60Hz).

This appliance can be used by children aged from 8 years and

above and people with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children

without supervision.

Remove the convector from its packaging and check that it is in good

condition before use. Keep any plastic bags away from children.

Check the cord and plug before using the convector to ensure that

they have not been damaged during transport.

This product is not a toy.

Children under the age of 3 must be kept away if not continuously

supervised.

Children aged between 3 and 8 must only turn the appliance on / off

as long as it has been placed or installed in its normal operating

position and that they receive surveillance or instructions regarding

the safe use of the appliance and understand the dangers.

Children between 3 and 8 years of age must not insert the plug,

adjust or clean the appliance or carry out maintenance by the user.

CAUTION - Some parts of this product can become very hot and

cause burns. Particular attention has to be given where children

and vulnerable people are present.

WARNING: In order to avoid hazard due to inadvertent resetting of

the thermal cut-out, this appliance must not be supplied through and

external switching device, such as a timer, or connected to a circuit

that is regularly switched on and off by the utility.

WARNING: do not use the convector with a controller or any

other external device that activates the appliance automatically,

V 05/21

as there may be a risk of fire if the fan heater is covered or

incorrectly positioned.

Disconnect the mains power when the appliance is not used or for

cleaning operations.

To disconnect the convector, turn off the appliance with the ON/OFF

switch on the side and remove the plug from the socket. Pull on the

plug only. Do not pull the cord.

Avoid placing fingers or foreign objects in the air inlet/outlet grilles,

as this may lead to electric shock or fire and may damage the

convector. To avoid the risk of fire, do not block the grilles or tamper

with them in any way while the convector operates.

Do not use the convector if the cord or plug is damaged. If the power

cable is damaged, it must be replaced by the manufacturer or its

technical assistance service or in any case by a person with a similar

qualification, in order to prevent any risk.

Do not place any objects on the cord and do not bend it. During

operation, the cord must be entirely unwound.

It is not advisable to use extension cords, as these may overheat

and cause the risk of fire. Do not use a single extension cord to

operate more than one convector.

The convector heats up significantly during operation. Risk of burn.

To avoid injury, do not allow skin to come into contact with a hot

surface. Use the handle to move the convector. Keep flammable

materials, such as furniture, cushions, blankets, paper, cloths,

curtains and suchlike at least 1 m from the front and back

Do not immerse the cord, plug or any other element of the panel in

water or other liquids.

Do not touch the plug or convector with wet hands.

Avoid using the convector in dusty environments or in the presence

of flammable vapors (e.g. in workshops or garages).

Do not place the convector above or near another heat source.

WARNING: AVOID COVERING THE CONVECTOR TO PREVENT IT

FROM OVERHEATING.

The symbol below signals the above warning:

V 05/21

The convector may cause risk of fire if, while in operation, is covered

by or comes into contact with flammable material including curtains,

drapery, blankets, etc. KEEP THE CONVECTOR AWAY FROM

THESE MATERIALS.

Do not insert and avoid accidental insertion of any external objects

into the ventilation or discharge outlets as this may lead to electric

shock, fire or damage the convector.

A convector contains parts that generate arcs or sparks. It must not

be used in potentially dangerous areas such as areas at risk of fire

or explosion, or areas loaded with chemical substances or humidity.

Do not use the convector on soft surfaces such as beds, where the

grilles may be covered. Always stand the convector on a flat, stable

surface when in operation, in order to prevent it from overturning.

Arrange the cord in such a way that the convector and other objects

do not rest on it. Do not run the cord under carpets. Do not cover the

cord with blankets, carpets or similar materials. Place the cord far

away from busy areas, or in a place where it cannot be accidentally

pulled-out.

Never position the convector where it may fall into a bath or other

containers of water.

Never position the convector on a wet floor.

In any case, the adjustment switches must never be accessible by

anyone in a bath or shower.

The heating appliance must not be positioned immediately below a

power outlet.

The socket must be earthed.

Do not allow the electric cord to touch the metal structure of the

convector when it is hot or in operation, in order to avoid the high

temperatures ruining the cord.

Do not operate the convector outdoors. Do not use the convector in

front of or near an open window.

WARNING: do not use the convector with an external controller

or any other external device that activates the convector

automatically, as there may be a risk of fire if the convector is

covered or incorrectly positioned.

Upon initial start-up, the convector may emit a slight, harmless smell.

This smell is a normal effect of the initial heating up of the internal

heating elements, and should not recur later on.

V 05/21

Do not attempt to repair, disassemble or modify the convector. The

convector does not contain parts that can be repaired by the user.

Turn the switch off and unplug before carrying out any maintenance

work or moving the convector. Always unplug from the socket when

the convector is not in use.

WARNING: ALWAYS UNPLUG WHEN CARRYING OUT

MAINTENANCE WORK OR MOVING THE CONVECTOR.

Do not place anything on the convector; avoid placing wet garments

on the convector.

Turn the appliance off if unattended in order to avoid accidents.

If the convector is not used for prolonged periods, disconnect the

plug, replace the convector in its box and store it in a dry, ventilated

place.

Ensure that the air inlet /outlet are not close to walls or curtains when

the convector is in use, so as to avoid obstructing the convector and

hampering its efficiency.

Place the convector at a distance of at least 1 meter from walls and

objects.

Should you hear an abnormal noise or detect an unusual smell when

using the convector, cease use and unplug immediately.

Do not expose the elderly or children to a continuous flow of air.

Do not use the convector if it has been damaged or dropped.

Do not use the convector without the feet mounted and do not use

feet other than those supplied with the product.

WARNING:

THE ON/OFF SWITCH IS NOT THE ONLY MEANS TO

DISCONNECT THE POWER SUPPLY. ALWAYS PULL OUT THE

PLUG FROM THE SOCKET IN THE EVENT OF MAINTENANCE

OPERATIONS, WHEN MOVING THE PANEL OR WHEN NOT IN

USE.

V 05/21

DESCRIPTION OF PARTS

1. Air outlet

2. Handle

3. Display and touch control panel

4. ON/OFF switch

5. Foot

HOW TO INSTALL THE APPLIANCE

The convector can be used on the floor, after assembling the feet.

MONTARE I PIEDINI IN DOTAZIONE

The convector is packed without feet. These must therefore be assembled before using the appliance.

Assemble the feet as shown in the figure and put the convector in an upright position. Position the unit on a flat,

stable surface.

1. Turn the convector upside down 2. Insert the feet. The longest part

must be positioned behind on

the rear the convector.

3. Tighten the wing nuts on the feet.

V 05/21

CONTROL PANEL AND FUNCTIONS

TOUCH CONTROL PANEL ON THE APPLIANCE

1 Low power heating LED

LED on display

2 High power heating LED

3 Display Temperature/Timer

4 Standby button

Operation buttons

5 Button -

6 Heating setting button

7 Button +

8 Brightness/Timer button

Connect the power cord to an appropriate power outlet (220-240V ~ 50-60Hz).

Press the power button located on the side of the convector, a beep will sound.

The button will light up on the control panel. Then press the Standby button on the panel to switch

on the convector. Press the same button to switch off the convector.

It is advisable to unplug the power cord if the product is not in use.

Heating mode selection button

Press this button to select the heating mode between high and low. According to the selection made on the

display, the corresponding LEDs will light up:

Icon on display

Heating power Low 1250W High

2000W

V 05/21

Temperature selection buttons and

Press the buttons on the control panel to select the desired temperature between 10 ° C up to 35 ° C.

When the temperature reaches 10 ° C, press the button and the anti-freeze function will be activated,

will appear on the display . When the anti-freeze function is active, the reference temperature is 7 ° C.

Timer Button and Display Illumination

Timer function: Press and hold the button for about 3 seconds, the display will show 0h, then press the

and buttons to select the operating interval from 1 to 9 hours (the time increases by 1 hour at each

selection), on the display the set time will be shown.

Display lighting function: The standard lighting is 100%, press the button to change the intensity of the

lighting in the following circular sequence 100% -> 50% -> 25% -> 0%

When the lighting intensity is 0%, the display is off, the Standby button and the Timer / Display lighting

button are always lit with a lighting intensity of 25%, if no selection is made.

MAINTENANCE AND STORAGE

ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE.

IMPORTANT: DO NOT SUBMERGE THE CONVECTOR IN WATER.

Cleaning the outside surface of the appliance

Turn the switch off and unplug before carrying out any maintenance work or moving the appliance.

Use a soft cloth to remove any dust from the convector.

If the convector is excessively dirty, use a soft cloth moistened with water and a mild detergent at a temperature lower

than 50°C. Let the convector dry completely before use.

Do not use corrosive detergents or solvents such as petrol. Do not wash the appliance with water. Do not use oils,

chemical substances or other items to clean that may damage the surface.

Use a vacuum cleaner to remove dust from the air inlet/outlet grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging, in

a cool and dry place.

V 05/21

Table 2

INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Annex II - Ecodesign requirements - Requirements for product information -

COMMISSION REGULATION (EU) 2015/1188 of 28 April 2015 implementing Directive 2009/125/EC of the European

Parliament and of the Council with regard to ecodesign requirements for local space heaters

Model identifier(s): DAKOTA

Item Symbol Value unit Item unit

Heat output Type of heat input, for electric storage local space

heaters only (select one)

Nominal heat output Pnom 1,9 kW manual heat charge control, with

integrated thermostat

[no]

Minimum heat output

(indicative)

Pmin 1,25 kW manual heat charge control with room

and/or outdoor temperature feedback

[no]

Maximum continuous

heat output

Pmax,c 1,9 kW electronic heat charge control with room

and/or outdoor temperature feedback

[no]

Auxiliary electricity

consumption

fan assisted heat output [no]

At nominal heat output elmax 0 kW Type of heat output/room temperature control

(select one)

At minimum heat output elmin 0 kW single stage heat output and no room

temperature control

[no]

In standby mode elsb 0 kW Two or more manual stages, no room

temperature control

[no]

with mechanic thermostat room

temperature control

[no]

with electronic room temperature control [yes]

electronic room temperature control plus

day timer

[no]

electronic room temperature control plus

week timer

[no]

Other control options (multiple selections

possible)

room temperature control, with presence

detection

[no]

room temperature control, with open

window detection

[no]

with distance control option [no]

with adaptive start control [no]

with working time limitation [no]

with black bulb sensor [no]

Seasonal energy efficiency of space heating ηS(%) 37

Contact details : ARGOCLIMA SPA - Via A. Varo,35 - Alfianello (BS) - ITALY -

www.argoclima.com

V 05/21

Information for correct disposal of the product in accordance with the European Directive 2012/19/EU

At the end of its working life this equipment must not be disposed of as an household waste. It must be taken to special local

community waste collection centres or to a dealer providing this service. Disposing of electrical and electronic equipment

separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and

enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to

underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.

www.argoclima.com

Inhaltsverzeichnis

Andere Argo Heizung Handbücher

Argo

Argo soul digit Bedienungsanleitung

Argo

Argo CLOE Bedienungsanleitung

Argo

Argo HI FLOOR RAY Bedienungsanleitung

Argo

Argo HI FAN black mini Bedienungsanleitung

Argo

Argo HiFan Digit Bedienungsanleitung

Argo

Argo Wally Bedienungsanleitung

Argo

Argo Symphony Bedienungsanleitung

Argo

Argo SPLITTO JR Bedienungsanleitung

Argo

Argo IP24 Bedienungsanleitung

Argo

Argo WILLIS Bedienungsanleitung

Argo

Argo drum Bedienungsanleitung

Argo

Argo MOOD Bedienungsanleitung

Argo

Argo Orange Bedienungsanleitung

Argo

Argo CREOLA Q3 Bedienungsanleitung

Argo

Argo HIFAN Black Bedienungsanleitung

Argo

Argo CULT Bedienungsanleitung

Argo

Argo Sleek Bedienungsanleitung

Argo

Argo SPLITTO Leitfaden

Argo

Argo WILMA Bedienungsanleitung

Argo

Argo Soultt Bedienungsanleitung

Argo

Argo BOBO Bedienungsanleitung

Argo

Argo ARKE TOWER Bedienungsanleitung

Argo

Argo Chic Bedienungsanleitung

Argo

Argo KASPER 9 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung