Argo ARKE TOWER Bedienungsanleitung

V 03/19

ARKE TOWER

This product is only suitable for correctly-insulated

environments or for occasional use.

OPERATING INSTRUCTIONS

Read the instructions carefully before operating the appliance or carrying out maintenance

operations.

Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or

damage. Keep these instructions in a safe place for future reference.

TOWER FAN HEATER

V 03/19

GENERAL SAFETY INFORMATION

•Use this fan heater only as outlined in this manual. Any other use

not recommended by the manufacturer may cause fire, electric

shock or injury to persons.

•Make sure that the type of mains power complies with the electrical

requirements of the fan heater (220-240 V~/50 Hz).

•This appliance can be used by children of at least 8 years of age

and by people with reduced physical, sensory or mental abilities, or

who lack sufficient experience or the necessary knowledge,

provided that they are supervised or have been instructed on how

to use the appliance safely and understand the hazards related to

its use.

•Children must not be allowed to play with the appliance.

•Cleaning and maintenance operations normally carried out by the

user must not be performed by unsupervised children.

•This product is not a toy. Children under the age of 3 years must

be kept out of reach unless properly supervised, to ensure that

they do not play with the appliance.

•Children aged between 3 and 8 years must only be able to turn the

appliance on/off, provided that the appliance has been placed in its

normal operating position, that instructions have been given on

how to use the equipment safely, and that its risks have been

understood.

•Children aged between 3 and 8 years must not be able to plug in,

adjust, clean or perform any maintenance on the appliance.

•WARNING: Certain parts of this product may become very hot and

cause burns. Special care should be taken when children and

vulnerable people are nearby.

•To avoid the risk of accidentally resetting the thermal protection,

this appliance must not be powered through an external switching

device, such as a timer, or connected to a circuit that is switched

on and off by the utility.

•WARNING: do not use the fan heater with a controller or any

other device that activates the appliance automatically, as

there may be a risk of fire if the fan heater is covered or

incorrectly positioned.

•Do not restrict the air inlet and outlet grilles.

•The appliance heats up significantly when running and can cause

burns. Avoid unprotected contact with the hot surface.

V 03/19

•Keep flammable materials, such as furniture, cushions, blankets,

paper, cloths, curtains and similar items at least 1 m away from the

front, sides and back of the appliance.

•Disconnect the mains power when the appliance is not in use or

during cleaning.

•Avoid using the fan heater in dusty environments or in the

presence of flammable vapours (e.g. in workshops or garages).

•Do not place anything on the product; avoid placing wet garments

on the fan heater.

•Use the heater in a well-ventilated area.

•Avoid placing fingers or foreign objects in the air inlet/outlet grilles,

as this may lead to electric shock or fire and may damage the

appliance.

•To avoid the risk of fire, do not block the grilles or tamper with

them in any way while the fan heater is in use.

•Do not use the appliance if the power cable or plug are

damaged. Contact a service centre to replace a damaged power

cable, so as to avoid any safety risks.

•Do not use the fan heater if it has fallen from a certain height or if it

has been damaged in any way. Contact a service centre to check

the fan heater or make any necessary electrical or mechanical

repairs.

•The most common cause of overheating is the build-up of dust in

the appliance. Remove accumulated dust by removing the plug

and cleaning the grilles using a vacuum cleaner.

•Do not use any abrasive products to clean the appliance. Clean it

using a damp cloth (not wet) rinsed with soapy water. Remove the

plug from the socket before performing any maintenance.

•To disconnect the fan heater, turn the switch to OFF and remove

the plug from the socket. Pull on the plug only. Do not pull on the

cable when turning off the fan heater.

•Do not place any objects on the cable and also avoid bending the

cable.

•Using extension leads is not recommended as they may overheat

and cause a fire hazard. Never use a single extension lead to

operate multiple appliances.

•Do not immerse the power cable, plug or any other part of the

appliance in water or other liquids.

•Do not touch the plug with wet hands.

V 03/19

•Do not place the fan heater above or near another heat source.

WARNING: AVOID COVERING THE FAN HEATER TO PREVENT

IT FROM OVERHEATING.

The symbol below signals this warning:

•The fan heater may cause the risk of fire if, while operating, it is

covered or comes into contact with flammable material including

curtains, drapery, blankets, etc. KEEP THE FAN HEATER AWAY

FROM THESE MATERIALS.

•Do not connect the fan heater to the power supply until it has been

correctly assembled or positioned.

•Do not run the cable under carpets. Do not cover the cable with

blankets, carpets or similar materials. Place the cable away from

busy areas and where it cannot accidentally be pulled out.

•Do not operate the fan heater in close proximity to bathtubs,

showers, washbasins or pools.

•Do not position the fan heater beneath a power socket.

•Do not operate the appliance outdoors.

•Upon initial start-up, the fan heater may emit a slight, harmless

smell. This smell is a normal effect of the initial heating up of the

internal heating elements, and should not recur subsequently.

WARNING:

THE ON/OFF SWITCH IS NOT THE ONLY METHOD OF

DISCONNECTING THE MAINS POWER.

ALWAYS UNPLUG THE APPLIANCE DURING MAINTENANCE

OPERATIONS, WHEN MOVING IT OR WHILE IT IS NOT IN USE.

•A fan heater contains parts that generate electrical arcs and

sparks. It must not be used in potentially dangerous areas such as

those subject to the risk of fire or explosion, or areas filled with

chemical substances or humidity.

•Do not use the appliance on soft surfaces such as beds, where the

grilles may get covered. Always rest the fan heater on a flat and

stable surface when it is running, so as to prevent it from toppling

over. Arrange the cable so that neither the fan heater or other

objects can be on top of it.

•Always unplug the appliance when it is not in use.

•Turn the appliance off if unattended, in order to prevent accidents.

V 03/19

•In the event of any anomalies (abnormal noise or a strange smell),

immediately turn off the appliance; do not attempt to repair it but

take it to your local service centre.

ASSEMBLY INSTRUCTIONS

Open the box and remove the parts of the appliance: body, base and remote control unit.

Combine the two halves of the base, as shown in the diagram.

Insert the cable into the central hole.

Insert the base onto the lower part of the appliance and tighten the 4 screws.

Stand the appliance up vertically on a level surface before switching on.

V 03/19

DESCRIPTION OF PARTS

1. Soft touch control panel

2. Hot air outlet grille

3. Base

4. Handle and remote control-holder

5. Air intake grill

6. Grille with filter

7. On/off switch

8. Power chord

CONTROL PANEL DISPLAY and REMOTE CONTROL

Front view

Rear view

V 03/19

ON/OFF BUTTON: Press this button to turn ok/off the fan heater.

ECO BUTTON: press this button to activate/deactivate ECO SMART function.

If the room temperature is below 18°C the fan heater will work in high heating

mode(2000W) when the temperature reach 18°C the fan heater will work in low

heating mode (1000W) when the room temperature is 25°C the fan heater stops

working and enter in stand-by mode. When room temperature decreases of 1°C

the fan heater will star to work again in low heating mode to reach again 25°C.

TIMER BUTTON: in working status you can select the timer off function. The timer

off can be setted (1-2-4-8 hours). If timer function is on the LED of the timer is on,

if no timer is sed the timer LED is off.

TEMPERATURE BUTTON: Select to activate countinuos mode, the fan

heater will work continuously until room temperature is 35°C. Press again this

button to select default temperatures (22°C-26°C-30°C). When the selected room

temperature is reached the fan heater will enter stand-by mode, when roome

temperature decreased of 1°C the fan heater will start to work again.

MODE BUTTON: Press this button to select the 3 different working modes:

Low heating

(1000W)

High heating

(2000W)

FAN ONLY

(32W)

SWING BUTTON: Press this button to activate/deactivate the swing function

REMOTE CONTROL

Use Lithium/Manganese button cells, model no. CR2032 -3 V, conforming to Battery Directive no. 2006/66/EC and

modification by Dir.no 2013/56/EU (supplied with the remote control).

HOW TO INSERT / REMOVE THE REMOTE CONTROL BATTERIES (refer to the diagram below)

Open the battery cover at the back of the remote control (press the back and pull the flap). Insert the battery into the slot,

making sure you respect the polarities. Put the cover back onto the remote control.

V 03/19

HOW TO USE THE FAN HEATER

Place the fan heater in a vertical position on a flat and stable surface. Connect the power cable to a suitable electric socket

(220-240V~/50Hz). Use the handle to move the appliance.

SWITCHING ON/OFF

Put the on/off button (on the rear) in the “I” position. When the appliance emits a “beep”, this means that the fan heater is

ready for use and enters stand-by mode. Press the button on the control panel or on the remote control to switch it

on. To switch off the fan heater, press the button again, let the unit cool down for about 30 seconds and switch the

button on the rear to “0” to turn the fan heater off.

HEATING

Press the button on the control panel or on the remote control to select the low (1000W) or high (2000W) heating

function. The LED in low function and in high function, will appear on the display. Select to activate the fan

only mode.

TIMER

When the fan heater is operating, press the button on the control panel or on the remote control to set the timer.

Select the switch-off timer (1-2-4-8 h). When the set timer expires, the fan heater switches to stand-by mode.

TEMPERATURE REGULATION

The temperature can be regulated via the remote control or the control panel; press the button.

In CONTNUOUS mode the heater works without interruption for a maximum of 12 hours, or until room temperature

is 55°C, the It will enter stand-by mode. It is not possible to restart the heater until the room temperature is below 45°C.

The heater can also work until room temperature reach one of the default temperature 22°C-26°C-30°C. When the

selected room temperature is reached the fan heater will enter stand-by mode, when roome temperature decreased of

1°C the fan heater will start to work again.

ECO SMART FUNCTION

When the unit is operating, press the “ECO” button to activate the ECO SMART mode: the matching LED will light on the

display. In this mode the heating power is adjusted automatically,

- When the room temperature is lower than the set temperature by a maximum of 1°C, the fan heater will operate at

low power (1000W).

- When the room temperature is lower than the set temperature by more than 1°C, the fan heater will operate at high

power (2000W).

- When the room temperature is equal to the set temperature, the fan heater goes into stand-by mode and switches

back on when the room temperature drops by at least 1°C.

The appliance is equipped with an anti-tipping device which interrupts operation when the product is tilted. Do not

position the appliance on its side or upside down.

INFORMATION FOR THE CORRECT DISPOSAL OF BATTERIES IN ACCORDANCE WITH EUROPEAN DIRECTIVE

2006/66/EC AND CHANGES INTRODUCED BY DIRECTIVE 2013/56 / EU

Replace batteries when they are depleted. At the end of their life, batteries must be disposed of separately from unsorted

waste. They must be taken to designated recycling centres or returned to a retailer providing this service. Separate

disposal of batteries prevents potential negative effects on the environment and human health due to inadequate disposal,

and also allows their constituent materials to be recovered and recycled, resulting in significant savings in terms of energy

and resources. In order to highlight the obligation regarding separate disposal, the battery carries the crossed-out dustbin

symbol. Illegal disposal of the product by the user may lead to administrative sanctions being applied as per current

regulations.

V 03/19

CAUTION: ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE OPERATIONS.

IMPORTANT: DO NOT IMMERSE THE CERAMIC FAN HEATER IN WATER

Cleaning the outside surface of the appliance

Use a soft cloth to remove any dust from the fan heater.

If the fan heater is excessively dirty, use a soft cloth dampened with water and neutral detergent at a temperature below

50°C. Leave the fan heater to dry completely before using it again.

Do not use corrosive detergents or solvents such as petrol. Do not wash the appliance with water. When cleaning the

appliance, do not use oils, chemical substances or other items that may damage the surface.

Use a vacuum cleaner to remove dust from the air inlet/outlet grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging, in a

cool and dry place.

MAINTENANCE AND STORAGE

V 03/19

INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Table 2 - Annex II - Ecodesign requirements - Requirements for product information -

COMMISSION REGULATION (EU) 2015/1188 of 28 April 2015 implementing Directive 2009/125/EC of the European

Parliament and of the Council with regard to ecodesign requirements for local space heaters

Model identifier(s): ARKE TOWER

Item

Symbol

Value

unit

Item

unit

Heat output

Type of heat input, for electric storage local space

heaters only (select one)

Nominal heat output

Pnom

2,0

manual heat charge control, with integrated

thermostat

[NA]

Minimum heat output

(indicative)

Pmin

0,944

manual heat charge control with room

and/or outdoor temperature feedback

[NA]

Maximum continuous

heat output

Pmax,c

2,055

electronic heat charge control with room

and/or outdoor temperature feedback

[NA]

Auxiliary electricity

consumption

fan assisted heat output

[NA]

At nominal heat output

elmax

Type of heat output/room temperature control (select

one)

At minimum heat output

elmin

single stage heat output and no room

temperature control

[no]

In standby mode

elsb

0,00026

Two or more manual stages, no room

temperature control

[no]

with mechanic thermostat room temperature

control

[no]

with electronic room temperature control

[yes]

electronic room temperature control plus

day timer

[no]

electronic room temperature control plus

week timer

[no]

Other control options (multiple selections possible)

room temperature control, with presence

detection

[no]

room temperature control, with open

window detection

[no]

with distance control option

[no]

with adaptive start control

[no]

with working time limitation

[no]

with black bulb sensor

[no]

Contact details :

ARGOCLIMA SPA - Via A. Varo,35 - Alfianello (BS) - ITALY -

www.argoclima.com

The seasonal space heating energy efficiency of all local space heaters except commercial

local space heaters, ηS(%)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argo Heizung Handbücher

Argo

Argo Soultt Bedienungsanleitung

Argo

Argo WILLIS Bedienungsanleitung

Argo

Argo HiFan Digit Bedienungsanleitung

Argo

Argo CLOE Bedienungsanleitung

Argo

Argo CREOLA Q3 Bedienungsanleitung

Argo

Argo CHIC SILVER Bedienungsanleitung

Argo

Argo Symphony Bedienungsanleitung

Argo

Argo HIFAN Bedienungsanleitung

Argo

Argo CLOVER Bedienungsanleitung

Argo

Argo DAKOTA Bedienungsanleitung

Argo

Argo KANSAS Bedienungsanleitung

Argo

Argo HIFAN Black Bedienungsanleitung

Argo

Argo Orange Bedienungsanleitung

Argo

Argo BOBO Bedienungsanleitung

Argo

Argo HI FAN black mini Bedienungsanleitung

Argo

Argo HUGO Bedienungsanleitung

Argo

Argo SILENCE 9 Bedienungsanleitung

Argo

Argo IP24 Bedienungsanleitung

Argo

Argo MARGE Bedienungsanleitung

Argo

Argo SPLITTO Leitfaden

Argo

Argo Sleek Bedienungsanleitung

Argo

Argo HIFAN HiFi Bedienungsanleitung

Argo

Argo CHIC SILVER Bedienungsanleitung

Argo

Argo LOXO Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung