Argo KANSAS Bedienungsanleitung

V 06/22

KANSAS

ELECTRIC CONVECTOR HEATER

This product is only suitable for correctly-insulated

environments or for occasional use.

OPERATING INSTRUCTIONS

Read the instructions carefully before operating the appliance or carrying out maintenance operations.

Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or damage.

Keep these instructions in a safe place for future reference.

12V 06/22

GENERAL SAFETY INFORMATION

• Use this convector only as outlined in this manual. Any other use not

recommended by the manufacturer may cause re, electric shock or

injury to persons.

• This convector is designed for domestic use. It must not be used for

commercial or industrial purposes.

• Ensure that the mains voltage complies with that indicated on the

convector data plate (220-240V~ 50-60Hz).

• This appliance can be used by children aged from 8 years and above

and people with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and

understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without

supervision.

• Remove the convector from its packaging and check that it is in good

condition before use. Keep any plastic bags away from children.

• Check the cord and plug before using the convector to ensure that they

have not been damaged during transport.

• This product is not a toy.

• Children under the age of 3 must be kept away if not continuously

supervised.

• Children aged between 3 and 8 must only turn the appliance on /

off as long as it has been placed or installed in its normal operating

position and that they receive surveillance or instructions regarding the

safe use of the appliance and understand the dangers.

• Children between 3 and 8 years of age must not insert the plug, adjust

or clean the appliance or carry out maintenance by the user.

• CAUTION - Some parts of this product can become very hot and

cause burns. Particular attention has to be given where children and

vulnerable people are present.

• WARNING: In order to avoid hazard due to inadvertent resetting of

the thermal cut-out, this appliance must not be supplied through and

external switching device, such as a timer, or connected to a circuit

that is regularly switched on and off by the utility.

13V 06/22

• WARNING: do not use the convector with a controller or any other

external device that activates the appliance automatically, as there may

be a risk of re if the fan heater is covered or incorrectly positioned.

• Disconnect the mains power when the appliance is not used or for

cleaning operations.

• To disconnect the convector, turn off the appliance by turning the heating

mode adjustment knob, located on the side and remove the plug from

the socket.

• Avoid placing ngers or foreign objects in the air inlet/outlet grilles, as

this may lead to electric shock or re and may damage the convector.

To avoid the risk of re, do not block the grilles or tamper with them in

any way while the convector operates.

• Do not use the convector if the cord or plug is damaged. If the power

cable is damaged, it must be replaced by the manufacturer or its

technical assistance service or in any case by a person with a similar

qualication, in order to prevent any risk.

• Do not place any objects on the cord and do not bend it. During

operation, the cord must be entirely unwound.

• It is not advisable to use extension cords, as these may overheat and

cause the risk of re. Do not use a single extension cord to operate

more than one convector.

• The convector heats up signicantly during operation. Risk of burn.

• To avoid injury, do not allow skin to come into contact with a hot surface.

Use the handle to move the convector. Keep ammable materials, such

as furniture, cushions, blankets, paper, cloths, curtains and suchlike at

least 1 m from the front and back

• Do not immerse the cord, plug or any other element of the panel in

water or other liquids.

• Do not touch the plug or convector with wet hands.

• Avoid using the convector in dusty environments or in the presence of

ammable vapors (e.g. in workshops or garages).

• Do not place the convector above or near another heat source.

WARNING: AVOID COVERING THE CONVECTOR TO PREVENT IT

FROM OVERHEATING.

14V 06/22

The symbol below signals this warning:

• The convector may cause risk of re if, while in operation, is covered

by or comes into contact with ammable material including curtains,

drapery, blankets, etc. KEEP THE CONVECTOR AWAY FROM THESE

MATERIALS.

• Do not insert and avoid accidental insertion of any external objects into

the ventilation or discharge outlets as this may lead to electric shock,

re or damage the convector.

• A convector contains parts that generate arcs or sparks. It must not

be used in potentially dangerous areas such as areas at risk of re or

explosion, or areas loaded with chemical substances or humidity.

• Do not use the convector on soft surfaces such as beds, where the

grilles may be covered. Always stand the convector on a at, stable

surface when in operation, in order to prevent it from overturning.

• Arrange the cord in such a way that the convector and other objects do

not rest on it. Do not run the cord under carpets. Do not cover the cord

with blankets, carpets or similar materials. Place the cord far away from

busy areas, or in a place where it cannot be accidentally pulled-out.

• Never position the convector where it may fall into a bath or other

containers of water.

• Never position the convector on a wet oor.

• In any case, the adjustment knobs must never be accessible by anyone

in a bath or shower.

• The heating appliance must not be positioned immediately below a

power outlet.

• The socket must be earthed.

• Do not allow the electric cord to touch the metal structure of the convector

when it is hot or in operation, in order to avoid the high temperatures

ruining the cord.

• Do not operate the convector outdoors. Do not use the convector in

front of or near an open window.

• Upon initial start-up, the convector may emit a slight, harmless smell.

This smell is a normal effect of the initial heating up of the internal

heating elements, and should not recur later on.

15V 06/22

• Do not attempt to repair, disassemble or modify the convector. The

convector does not contain parts that can be repaired by the user.

• Turn the switch off and unplug before carrying out any maintenance

work or moving the convector. Always unplug from the socket when the

convector is not in use.

• WARNING: ALWAYS UNPLUG WHEN CARRYING OUT

MAINTENANCE WORK OR MOVING THE CONVECTOR.

• Do not place anything on the convector; avoid placing wet garments

on the convector.

• Turn the appliance off if unattended in order to avoid accidents.

• If the convector is not used for prolonged periods, disconnect the plug,

replace the convector in its box and store it in a dry, ventilated place.

• Ensure that the air inlet /outlet are not close to walls or curtains when

the convector is in use, so as to avoid obstructing the convector and

hampering its efciency.

• Place the convector at a distance of at least 1 meter from walls and

objects.

• Should you hear an abnormal noise or detect an unusual smell when

using the convector, cease use and unplug immediately.

• Do not expose the elderly or children to a continuous ow of air.

• Do not use the convector if it has been damaged or dropped.

• Do not use the convector without the feet mounted and do not use feet

other than those supplied with the product.

• WARNING: THE HEATING SETTING KNOB IS NOT THE ONLY

MEANS TO DISCONNECT THE POWER SUPPLY. ALWAYS PULL OUT

THE PLUG FROM THE SOCKET IN THE EVENT OF MAINTENANCE

OPERATIONS, WHEN MOVING OR WHEN NOT IN USE.

16V 06/22

1. Air outlet

2. Carrying handle

3. Thermostat adjustment knob

4. Heating mode adjustment knob

5. Feet

DESCRIPTION OF PARTS

The convector can be used on the oor, after mounting the feet.

ASSEMBLE THE FEET SUPPLIED

In the packaging, the convector does not have its feet, which must therefore be mounted before putting the appliance

into operation.

Assemble the feet as described and then put the convector back upright.

HOW TO INSTALL THE APPLIANCE

1. Turn the convector

upside down 2. Insert the feet. The longest part must be

positioned behind on the rear the convector 3. Tighten the wing nuts on

the feet.

17V 06/22

HOW TO USE THE CONVECTOR

Connect the power cord to an appropriate power outlet (220-240V ~ 50-60Hz).

Use the heating mode adjustment knob to set the convector to function (when it is off it is in position 0), selecting the

desired heating mode from:

I (ECO 750 W) - II (COMFORT 1250 W) - III (SUPER 2000 W)

Then turn the thermostat adjustment knob to set the desired temperature.

When you want to switch off the convector, turn the heating mode adjustment knob again, bringing it to the 0 position

and turn the thermostat adjustment knob to the minimum position.

In case of prolonged non-use, unplug the power cord from the power outlet.

ANTI OVERHEATING DEVICE

The convector is equipped with an overheating device, which automatically stops its operation.Then switch off the

convector, check that the air outlet grilles are not blocked, then wait at least 5 minutes to allow the device to reset itself

and resume operation.

If the device does not resume normal operation or if the problem persists, contact a qualied service center.

CAUTION: ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE OPERATIONS.

IMPORTANT: DO NOT IMMERSE THE CONVECTOR IN WATER

Cleaning the outside surface of the appliance

Use a soft cloth to remove any dust from the convector. If the convector is excessively dirty, use a soft cloth dampened with water

and neutral detergent at a temperature below 50°C. Leave the fan heater to dry completely before using it again. Do not use

corrosive detergents or solvents such as petrol. Do not wash the appliance with water. When cleaning the appliance, do not use

oils, chemical substances or other items that may damage the surface. Use a vacuum cleaner to remove dust from the air inlet/

outlet grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging, in a cool

and dry place.

MAINTENANCE AND STORAGE

18V 06/22

Model identier(s): KANSAS

Item Symbol Value Unit Item Unit

Heat output Type of heat input, for electric storage local space

Heaters only (select one)

Nominal heat output Pnom 1,8-2,0 kW Manual heat charge control, with integrated

Thermostat [no]

Minimum heat output

(indicative) Pmin 0,75 kW Manual heat charge control with room

And/or outdoor temperature feedback [no]

Maximum continuous heat

output Pmax,c 2,0 kW Electronic heat charge control with room

And/or outdoor temperature feedback [no]

Auxiliary electricity

consumption Fan assisted heat output [no]

At nominal heat output elmax N/A kW Type of heat output/room temperature control (select one)

At minimum heat output elmin N/A kW Single stage heat output and no room

Temperature control [no]

In standby mode elsb 0 kW Two or more manual stages, no room

Temperature control [no]

With mechanic thermostat room

Temperature control [yes]

With electronic room temperature control [no]

Electronic room temperature control plus

Day timer [no]

Electronic room temperature control plus

Week timer [no]

Other control options (multiple selections possible)

Room temperature control, with presence

Detection [no]

Room temperature control, with open

Window detection [no]

With distance control option [no]

With adaptive start control [no]

With working time limitation [no]

With black bulb sensor [no]

The seasonal space heating energy efciency ηs(%) 36

Contact details: ARGOCLIMA SPA - Via A. Varo,35 - Alanello (BS) - ITALY - www.argoclima.com

INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Table 2 - Annex II - Ecodesign requirements - Requirements for product information - COMMISSION REGULATION (EU) 2015/1188

of 28 April 2015 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign

requirements for local space heaterslocale.

19V 06/22

INFORMATION ON THE CORRECT DISPOSAL OF THE PRODUCT pursuant to Art. 26 of (Italian)

Legislative Decree no. 49 of 14/03/14, “IMPLEMENTATION OF DIRECTIVE 2012/19/EU ON WASTE

ELECTRICAL AND ELECTRONIC EQUIPMENT”

At the end of its useful life, this appliance must not be disposed of together with household waste. We call

your attention to the crucial role played by the consumer in the reuse, recycling and other forms of recovery

of such waste. The dismantled appliance, with its components collected separately, must be delivered to

the local waste disposal facility or returned to the dealer free of charge when purchasing a new equivalent

appliance. Sorted disposal of electric and electronic equipment prevents potentially negative consequences

on the environment and human health due to improper waste disposal, and also allows the constituent

materials to be recovered and recycled, with signicant savings in terms of energy and resources. In order

to highlight the obligation regarding separate disposal of these devices, the appliance carries the crossed-

out wheeled bin symbol.

www.argoclima.com

Argoclima assumes no responsibility for any errors or inaccuracies in the content of this manual and reserves the right to make any changes to this

manual at any time and without notice, deemed appropriate for any technical or commercial need.

Inhaltsverzeichnis

Andere Argo Heizung Handbücher

Argo

Argo DAKOTA Bedienungsanleitung

Argo

Argo CREOLA Q3 Bedienungsanleitung

Argo

Argo HiFan Digit Bedienungsanleitung

Argo

Argo MOOD Bedienungsanleitung

Argo

Argo CLOVER Bedienungsanleitung

Argo

Argo HI FLOOR DESIGN Bedienungsanleitung

Argo

Argo HI FAN black mini Bedienungsanleitung

Argo

Argo HI FAN Bedienungsanleitung

Argo

Argo soul digit Bedienungsanleitung

Argo

Argo WILLIS Bedienungsanleitung

Argo

Argo HI FLOOR RAY Bedienungsanleitung

Argo

Argo SILENCE 9 Bedienungsanleitung

Argo

Argo SPLITTO JR Bedienungsanleitung

Argo

Argo ARKE TOWER Bedienungsanleitung

Argo

Argo HIFAN HiFi Bedienungsanleitung

Argo

Argo LOXO Bedienungsanleitung

Argo

Argo HIFAN Black Bedienungsanleitung

Argo

Argo IP24 Bedienungsanleitung

Argo

Argo SPLITTO Leitfaden

Argo

Argo BETSY Bedienungsanleitung

Argo

Argo CULT Bedienungsanleitung

Argo

Argo HUGO Bedienungsanleitung

Argo

Argo Dream IP21 Bedienungsanleitung

Argo

Argo KASPER 9 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung