Argo CLOVER Bedienungsanleitung

14V 07/22

CLOVER

IPX2

WALL-MOUNTED CERAMIC FAN HEATER

This product is only suitable for well

insulated spaces or occasional use.

OPERATING INSTRUCTIONS

Read the instructions carefully before operating the panel or carrying out maintenance operations.

Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or damages.

Store these instructions.

15V 07/22

• Use this fan heater only as outlined in this manual. Any other use not

recommended by the manufacturer may cause re, electric shock or

injury to persons.

• Make sure that the type of mains power complies with the electrical

requirements of the fan heater (220-240 V~50 Hz).

• This fan heater is designed for wall-installation; it must be mounted

1.8 m above the oor and at least 25 cm from the wall on each side.

Do not use it as a oor-standing device.

• This appliance can be used by children of at least 8 years of age

and by people with reduced physical, sensory or mental abilities, or

who lack sufcient experience or the necessary knowledge, provided

that they are supervised or have been instructed on how to use the

appliance safely and understand the hazards related to its use.

• Children must not be allowed to play with the appliance.

• Cleaning and maintenance operations normally carried out by the user

must not be performed by unsupervised children.

• This product is not a toy.

• Children under the age of 3 must be kept away if not continuously

supervised.

• Children aged between 3 and 8 must only turn the appliance on/

off as long as it has been placed or installed in its normal operating

position and that they receive surveillance or instructions regarding the

safe use of the appliance and understand the dangers.

• Children between 3 and 8 years of age must not insert the plug, adjust

or clean the appliance or carry out maintenance by the user

WARNING: Certain parts of this product may become very hot

and cause burns. Special care should be taken when children and

vulnerable people are nearby.

• To avoid the risk of accidentally resetting the thermal protection, this

appliance must not be powered through an external switching device,

such as a timer, or connected to a circuit that is switched on and off by

the utility.

• WARNING: Do not use the fan heater with a controller or any other

device that activates the appliance automatically, as there may be a

GENERAL SAFETY INFORMATION

16V 07/22

risk of re if the fan heater is covered or incorrectly positioned.

• The appliance is equipped with an IPX2 degree of protection and can

be used in private bathrooms in zone 2.

• Do not restrict the air inlet and outlet grilles.

• The appliance heats up signicantly when running and can cause burns.

Avoid unprotected contact with the hot surface.

• Keep ammable materials, such as furniture, cushions, blankets, paper,

cloths, curtains and similar items at least 1 m away from the front, sides

and back of the appliance.

• Disconnect the mains power when the appliance is not in use or during

cleaning.

• Avoid using the fan heater in dusty environments or in the presence of

ammable vapours (e.g. in workshops or garages).

• Do not place anything on the product; avoid placing wet garments on

the fan heater.

• Use the fan heater in a well-ventilated area.

• Avoid placing ngers or foreign objects in the air inlet/outlet grilles, as

this may lead to electric shock or re and may damage the fan heater.

• To prevent the risk of re, do not block the grilles or tamper with them

in any way while the fan heater is in use.

• Do not use the appliance if the power cable or plug are damaged. If

the power cable is damaged, it must be replaced by the manufacturer

or its technical assistance service or in any case by a person with a

similar qualication, in order to prevent any risk.

• Do not use the fan heater if it has fallen from a certain height or if it has

been damaged in any way. Contact a service centre to check the fan

heater or make any necessary electrical or mechanical repairs.

• The most common cause of overheating is the build-up of dust in the

17V 07/22

appliance. Remove accumulated dust, after taking the plug out, by

cleaning the grilles using a vacuum cleaner.

• Do not use any abrasive products to clean the appliance. Clean it

using a damp (not wet) cloth rinsed in soapy water. Remove the plug

from the socket before performing any maintenance.

• To disconnect the fan heater, turn the switch to OFF and remove the

plug from the socket. Pull on the plug only. Do not pull on the cable

when turning off the fan heater.

• Do not place any objects on the cable and also avoid bending the

cable.

• Using extension leads are not recommended as they may overheat

and cause a re hazard. Never use a single extension lead to operate

multiple appliances.

• Do not immerse the power cable, plug or any other part of the appliance

in water or other liquids.

• Do not touch the plug with wet hands.

• Do not place the fan heater above or near another heat source.

WARNING: AVOID COVERING THE FAN HEATER TO PREVENT IT

FROM OVERHEATING.

The symbol below signals this warning:

• The fan heater may cause the risk of re if, while operating, it is covered

or comes into contact with ammable material including curtains,

drapery, blankets, etc. KEEP THE FAN HEATER AWAY FROM THESE

MATERIALS.

• Do not connect the fan heater to the power supply until it has been

correctly assembled or positioned.

• Do not run the cable under carpets. Do not cover the cable with blankets,

carpets or similar materials. Place the cable away from busy areas and

where it cannot accidentally be pulled out.

• Do not operate the fan heater in close proximity to bathtubs, showers,

washbasins or pools.

• Do not use in bathrooms.

• Do not position the fan heater beneath a power socket.

• Do not operate the appliance outdoors.

• Upon initial start-up, the fan heater may emit a slight, harmless smell.

18V 07/22

• This smell is a normal effect of the initial heating up of the internal

heating elements, and should not recur subsequently.

WARNING: THE ON/OFF SWITCH IS NOT THE ONLY METHOD

OF DISCONNECTING THE MAINS POWER. ALWAYS UNPLUG

THE APPLIANCE DURING MAINTENANCE OPERATIONS, WHEN

MOVING IT OR WHILE IT IS NOT IN USE.

• A fan heater contains parts that generate electrical arcs and sparks.

• It must not be used in potentially dangerous areas such as those subject

to the risk of re or explosion, or areas lled with chemical

substances or humidity.

• Always unplug the appliance when it is not in use.

• Turn the appliance off if unattended, in order to prevent accidents.

• In the event of any anomalies (abnormal noise or a strange smell),

immediately turn off the appliance; do not attempt to repair it but take

it to your local service centre.

DESCRIPTION OF PARTS

1) Automatic ap

2) Air outlet grid

3) Base

4) On/off switch

5) LED light display

6) Front panel

7) Remote control

19V 07/22

The fan heater must be installed on the wall before use. Do not try to use it without installation. The installation

sequence is listed below:

1. Select a space for installing the appliance (gure 1).

2. Drill two holes on the wall that are suitably sized for inserting the Ø 8 mm Fischer screw plugs. (gure 2)

D= 394 mm

HOW TO INSTALL THE FAN HEATER

3. Insert the Fischer screw plugs into the holes and tighten the screws provided.

NOTE: Tighten the screws securely. Do not insert the screws into the Fischer plugs entirely - leave around 10 mm

free.

4. Mount the appliance on the wall (gure 3).

Ensure that the holes on the rear of the appliance are directed towards the two screws, push the fan heater

backwards onto the wall then downwards until it lies in a stable position.

CONTROL PANEL

Timer button

LED timer

LED mode

open window

F button (function selection)

ECO mode LED

(energy saving 1100 W)

LED COMFORT mode

(maximum heat 2000 W)

LED °C temperature

LED weekly timer

Ambient temperature display



°C

FIGURE 1 FIGURE 2 FIGURE 3

394 mm

Connect the power cable to a suitable electric socket (220-240V~50Hz), as indicated in the data plate.

SWITCHING THE FAN HEATER ON

Press the button on the appliance to switch the fan heater to stand-by mode. Press the on the remote control

to switch the appliance ON.

20V 07/22

AUTOMATIC FLAP SWIVEL

Press the button on the control panel or on the remote control to select the operating mode..

ACTIVATION OF SUMMER VENTILATION (FAN) AND HEATING (ECO – COMFORT) MODES

Press the button on the control panel or on the remote control to select the operating mode.

In stand-by mode the LED display is the following:

In Summer ventilation (FAN) mode the LED display is the following:

In ECO heating mode (1100 W) the LED display is the following:

In COMFORT heating mode (2000 W) the LED display is the following:

To return to stand-by mode press the buttons or again respectively on the appliance and on the remote control.

The default set temperature is 23 °C. The fan heater switches off about 30 seconds after the stand-by mode has been

activated.

ECO SMART FUNCTION

The fan heater operates at maximum power (COMFORT mode) when the set temperature is at least 4 °C higher than

the room temperature; if the set temperature is 0-2 °C higher than the room temperature, the fan heater operates at

medium power (ECO mode), if the room temperature is higher than the set temperature the fan heater switches off and

starts operating again when the room temperature drops 2 °C below the set temperature.

TEMPERATURE REGULATION

The temperature can only be set via the remote control. Press the + or – buttons to regulate the desired temperature

(from 10 °C to 49 °C).

If you set the temperature to 25 °C the “°C” LED comes on as shown in the gure:

Press to cancel the temperature setting.

ON/OFF DAILY TIMER SETTING

In stand-by mode, press the button to set the switch-on timer. The switch-on timer can be set from 1 to 12 hours, by

pressing on the same button to move on in intervals of 1 h: the default set temperature when it switches on is 23 °C.

When the appliance is operating, to set the switch-off timer press the , button; the switch-off button can be set from



 



 



°C

21V 07/22

1 to 12 hours, by pressing on the same button to move on in intervals of 1 h.

TIME SETTING (only from the remote control)

Press the SET button to show the time on the display; press the + or – buttons to set the current hour (00-23); press

the SET button again to set the minutes (00-59); press the SET button again to set the day of the week – if you press

+ or – the display will show the following abbreviations: d1, d2, d3,… which correspond respectively to Monday,

Tuesday, Wednesday etc.; once you have selected the current day press OK to conrm.

SETTING THE WEEKLY TIMER (only via the remote control)

After having set the time and day of the week, press P to enter the weekly timer setting:

1. Press DAY to set the switch-on day (d1, d2, d3,...),

2. Press EDIT to set the operating periods for the fan heater (P1, P2,… P6)

3. Press TIMER/ON to set the switch-on time (00-24)

4. Press TIMER/OFF to set the switch-off time (00-24)

5. Press the + or – buttons to set the desired temperature

6. Press OK to conrm the settings

To set any other subsequent operating times, (max 6) repeat the procedure from point 2 to point 6.

Repeat the procedure from point 1 to set the other days of the week.

After completing the weekly timer setting, press the buttons DAY EDIT TIMER/ON and TIMER/OFF to check the settings

for each day.

All settings are deleted when the fan heater is switched off using this switch

“OPEN WINDOW SENSOR” FUNCTION SETTING

When the appliance is operating, press the button on the remote control to activate the open window function;

the LED appears on the display, as shown in the gure:

Press the + or – buttons to set the temperature. When this function is active, if the room temperature drops by 5-10 °C

in less than 10 minutes, the fan heater stops operating and switches to stand-by mode.

Press to restart the appliance. If both the weekly timer and open window functions are set and, according to

the weekly programme, the appliance is off, the window open function will also be inactive. Conversely, when the

appliance is operating in line with the weekly programme, the window open function can control the ON/OFF

operation of the appliance.



°C



°C

no week timer

function set with week timer

function set

22V 07/22

REMOTE CONTROL

The functions of the remote control correspond to those on the control panel. Use a Lithium/Manganese button

cell, model no. CR2025-3 V, compliant with Battery Directive no.N 2006/66/EC and amendments to Directive

56/2013/EU (not provided)

HOW TO INSERT/REMOVE THE REMOTE CONTROL BATTERY (refer to the drawings below)

Open the battery door on the back of the remote control (press the back and pull the door). Place the battery in the

door, taking care to check the correct positioning of the polarity. Insert the cover into the remote control.

WARNINGS FOR BATTERIES

• Batteries must not be exposed to heat sources such as re, sun or similar sources; remove batteries if they start to

heat up or if the appliance is not used for a long time

• Batteries must be installed correctly in the appropriate battery compartment;

• Dispose of batteries that have reached the end of life or have been damaged in accordance with the national

regulations in force and listed below.

• In case of loss of battery uid, remove all batteries, preventing the spilled liquid from coming into contact with the

skin or clothing. If the liquid from the battery comes into contact with the skin or clothing, wash the skin with water

immediately. Before inserting new batteries, thoroughly clean the battery compartment with a paper towel cloth,

or follow the battery manufacturer’s recommendations for cleaning.

ATTENTION!

Danger of explosion if the battery is replaced with an incorrect type. Use and replace only batteries with the same

size and type. Improper use of batteries can cause liquid leakage, overheating or explosion. This liquid is corrosive

and can be toxic. It can cause skin and eye burns, and is harmful to swallow.

To reduce the risk of injury:

• Keep batteries out of the reach of children.

• Do not heat, open, puncture, cut or throw batteries into re.

• Do not mix old and new batteries or batteries of different types

• Do not leave metal objects that may come into contact with the battery terminals and therefore may heat up and/

or cause burns

1. ON/OFF button

2. SET button (settings)

3. TIMER button

4. Temperature regulation

5. OK button (conrm)

6. Function button open window

7. ON timer button (weekly timer on)

8. EDIT button (weekly timer operation period)

9. OFF timer buttons (weekly timer off)

10. DAY button (weekly timer day)

11. P button (weekly timer activation)

12. Temperature regulation

13. MODE button

14. SWING button

CR2025

23V 07/22

INFORMATION FOR THE CORRECT DISPOSAL OF BATTERIES IN ACCORDANCE WITH EUROPEAN

DIRECTIVE 2006/66/EC AND CHANGES INTRODUCED BY DIRECTIVE 2013/56/EU

Replace batteries when they are depleted. At the end of their life, batteries must be disposed of separately

from unsorted waste. They must be taken to designated recycling centres or returned to a retailer providing

this service. Separate disposal of batteries prevents potential negative effects on the environment and human

health due to inadequate disposal, and also allows their constituent materials to be recovered and recycled,

resulting in signicant savings in terms of energy and resources. In order to highlight the obligation regarding

separate disposal, the battery carries the crossed-out dustbin symbol. Illegal disposal of the product by the

user may lead to administrative sanctions being applied as per current regulations.

OVERHEATING SAFETY DEVICE

MAINTENANCE AND STORAGE

In the event of overheating, the protection system of the appliance will automatically disable the heating elements and

the motor, thus causing the fan heater to stop working.

In this case:

• turn the fan heater off;

• remove the causes of the overheating (e.g. obstacles in front of the air input/output grilles, dust build-up inside

the appliance, etc.);

• leave the appliance to cool down for 15-20 minutes;

• turn the fan heater on again and check that it works properly.

If the malfunction persists, contact an Authorised Service Centre.

CAUTION: ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR PERFORMING ANY MAINTENANCE.

IMPORTANT: DO NOT SUBMERGE THE FAN HEATER IN WATER.

Cleaning the outside surface of the appliance

Switch off the appliance and unplug it before cleaning or moving the appliance. Use a soft cloth to remove any dust

from the product. If this is not enough, use a soft cloth dampened with water and neutral detergent at a temperature

below 50 °C. Leave the appliance to dry thoroughly before using it again. Do not use corrosive detergents or solvents

such as petrol. Do not wash the appliance with water. When cleaning the appliance, do not use oils, chemical

substances or other items that may damage the surface. Use a vacuum cleaner to remove dust from the air inlet/outlet

grilles.

STORAGE

If the appliance is not used for prolonged periods, it must be stored together with this manual in its original packaging,

in a cool and dry place.

Inhaltsverzeichnis

Andere Argo Heizung Handbücher

Argo

Argo HUGO Bedienungsanleitung

Argo

Argo Chic Bedienungsanleitung

Argo

Argo MARGE Bedienungsanleitung

Argo

Argo KANSAS Bedienungsanleitung

Argo

Argo Soultt Bedienungsanleitung

Argo

Argo CULT Bedienungsanleitung

Argo

Argo ARKE TOWER Bedienungsanleitung

Argo

Argo Wally Bedienungsanleitung

Argo

Argo DAKOTA Bedienungsanleitung

Argo

Argo HiFan Digit Bedienungsanleitung

Argo

Argo SPLITTO Leitfaden

Argo

Argo BOBO Bedienungsanleitung

Argo

Argo HIFAN HiFi Bedienungsanleitung

Argo

Argo BETSY Bedienungsanleitung

Argo

Argo CLOE Bedienungsanleitung

Argo

Argo CHIC SILVER Bedienungsanleitung

Argo

Argo HIFAN Bedienungsanleitung

Argo

Argo CREOLA Q3 Bedienungsanleitung

Argo

Argo Sleek Bedienungsanleitung

Argo

Argo SILENCE 9 Bedienungsanleitung

Argo

Argo IP24 Bedienungsanleitung

Argo

Argo WHISPER 9 Bedienungsanleitung

Argo

Argo HIFAN Black Bedienungsanleitung

Argo

Argo HI FAN black mini Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung