Argos Athina 1000 Wall Unit Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 100cm

Depth - 29cm

Height - 70cm

Athina - 1000 Wall Unit

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 03/02/14

Important - Please read these instructions fully before starting assembly

608/0842

608/0969

608/0907

608/3014

608/1023

ALR2461

Issue 2 - 25/03/11 - Added Argos Code 608/3014

Issue 3 - 03/02/14 - Added note to fittings page and fitting of wall brackets, to say that the wall brackets can have 2 or 3 holes.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 23kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

bracket supplied

Components - Panels

Please check you have all the panels listed below

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Side (D0331A)

(700 x 290mm) x 2

Door (D0332A)

(700 x 497mm) x 2

45Back (X738)

(980 x 698mm)

Top/Base (D0333A)

(970 x 269mm) x 2

Munting (D0335A)

(668 x 60mm)

Shelf (D0334A)

(969 x 197mm)

Please check you have all the fittings listed below

Tools required

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 6

Metal dowel (F901) x 8

Shelf support (F110) x 4

G H

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Nail (F51) x 14

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M N

K L

Electric drill

Large locking

nut (F900) x 8

25mm Screw (F50) x 4 13mm Screw (F63) x 8

40mm Screw (F910) x 2

Door Buffer (F137) x 4

Handle (F847a ) x 2

aNHandle Screw (F847b) x 4

Hinge Plate

(F853) x 4

Hinge (F852) x 4

Hanging bracket

(F849) x 2

Wall bracket (F198) x 2

This shows a bracket

with 3 holes. They

can also be supplied

with just 2 holes.

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

This is the

left side

This is the

left side

Prepare the left side

Use one of the side

panels to make the

left side.

a: Fit 2 hinge plates

onto the left side ,

making sure that the slot

is facing towards the

front edge.

Fit a hanging bracket

to the left side using

2 screws , making

sure that the hook is

towards the back edge.

b: Screw 4 metal

dowels into the holes

on the left side as

shown.

Note: Tighten metal

dowels up fully against

the panels.

Front

edge

Prepare drawer fronts

and wraps x 3

a: Screw 2 x metal

dowels into the holes

on the back of the

drawer fronts .

Note: Tighten metal

dowels up fully against

the panels.

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 2

Front

edge

This is the

right side

This is the

right side

Prepare the right side

Use one of the side

panels to make the

left side.

a: Fit 2 hinge plates

onto the right side ,

making sure that the slot

is facing towards the

front edge.

Fit a hanging bracket

to the right side using

2 screws , making

sure that the hook is

towards the back edge.

b: Screw 4 metal

dowels into the holes

on the right side as

shown.

Note: Tighten metal

dowels up fully against

the panels.

Finished

front edge

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 3

Finished

front edge

Step 4

Fit the base and top

to the right side

Push the base and top

panels onto the right

side .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the base and top .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

2Right Side

Top

Finished

front edge

Base

Prepare the top and

base

Insert 4 large locking

nuts into the 2

top/base panels as

shown.

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Tap 2 wooden dowels

into the 2 top/base

panels as shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

10mm

Assembly Instructions

Step 5

Fit the munting

Fit the munting to the

top and base panels

and secure using 2

screws .

Step 6

Step 7

Fit the left side

Push the left side

onto the base and top

panels .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the base and top .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Prepare the munting

Tap 2 wooden dowels

into the munting as

shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Fit top and base to

the right side

Attach top to the right

side using the dowel

already fitted and secure

with 2 screws ..

Attach base to the

right side using the

dowel already fitted and

secure with 2 screws .

Top

Base

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 8

Fit the back

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

Note: The cut-out

corners of the back

must be at the top of the

unit.

b: Slide the back

into the grooves along

the side panels .

Push it into the grooves

until it is flush with the

bottom end of the side

panels .

c: Secure the back

by tapping 7 nails

down into the back edge

of the base and 7

nails into the back

edge of the top .

Cut-out

corner

Cut-out

corner

Top

Base

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Base

Top

964mm

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 9

Fit the unit to the wall

To fix the unit to the wall,

place the unit in the

required position and

lightly mark the outline of

the top corners of the

unit with a pencil.

Fit the 2 wall brackets

to the dimensions shown

in the top diagram.

The screws and plugs

are not supplied as they

need to be the correct

type to suit your wall.

Place your unit onto the

wall brackets , via the

hanging brackets

which you have fitted to

the sides of the unit.

Use the screw in the

bottom of the wall

brackets to adjust the

height of the unit.

Finally, pull the unit up

against the wall by

tightening up the top

screw in the hanging

brackets .

18mm

37mm

964mm

18mm

To adjust the height of

the unit on the wall,

turn the bottom screw

Pull the unit up

against the wall

by tightening

the top screw

Warning: Take

care when

drilling the wall

that you do not drill into

any pipes, wires etc. If in

doubt, consult an expert.

F F

Outline of

the unit

Warning: The

unit is heavy.

Lift with care.

Note: The diagrams show the wall brackets with 3 holes.

They can also be supplied with just 2 holes.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos 609/1886 Bedienungsanleitung

Argos

Argos Constable 149/2545 Bedienungsanleitung

Argos

Argos Canterbury 2 DR 2 DRW ROBE Bedienungsanleitung

Argos

Argos Stowe 427/0977 Bedienungsanleitung

Argos

Argos Arvika 357/6823 Bedienungsanleitung

Argos

Argos 869/6571 Bedienungsanleitung

Argos

Argos Devon 532/7623 Bedienungsanleitung

Argos

Argos Harrington Bedienungsanleitung

Argos

Argos 600/0509 Bedienungsanleitung

Argos

Argos Hallingford 802/6622 Bedienungsanleitung

Argos

Argos 2 Door Media Unit/Low Sideboard 482/0437 Bedienungsanleitung

Argos

Argos Oakhampton 391/8333 Bedienungsanleitung

Argos

Argos Capella Bedienungsanleitung

Argos

Argos Lamberto Ottoman TV Bed Bedienungsanleitung

Argos

Argos 365/9654 Bedienungsanleitung

Argos

Argos Washington Bedienungsanleitung

Argos

Argos 719/1792 Bedienungsanleitung

Argos

Argos 322/8645 Bedienungsanleitung

Argos

Argos NOMAD 727/7290 Bedienungsanleitung

Argos

Argos 8146643 Bedienungsanleitung

Argos

Argos Charlie 332/7553 Bedienungsanleitung

Argos

Argos Aubrey 549/6516 Bedienungsanleitung

Argos

Argos Iceland 178/6361 Bedienungsanleitung

Argos

Argos Silbury 4184719 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung