Argos Athina 500 Tall Cupboard Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59cm

Height - 200cm

Athina - 500 Tall Cupboard

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 04/01/10

Important - Please read these instructions fully before starting assembly

608/0794

608/0914

608/0859

608/0976

ALR2457

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 51kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

brackets supplied.

• Dispose of all packaging

carefully and responsibly.

bracket supplied

Components - Panels

Please check you have all the panels listed below

80%

x 3

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Plinth (D0322A)

(470 x 150mm)

Shelf (D0320A)

(469 x 427mm) x 2

Horizontal (D0319A)

(470 X 499mm) x 3

Left Side (D0328A)

(2000 X 570mm)

Right Side (D0329A)

(2000 X 570mm)

Back (X741)

(1848 x 480mm)

Small Door (D0317A)

(716 x 497mm)

Large Door (D0330A)

(1126 x 497mm)

Please check you have all the fittings listed below

Tools required

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 20

Metal dowel (F901) x 14

Shelf support (F110) x 8

E F

G H I

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Nail (F51) x 8

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill

Large locking

nut (F900) x 14

Bracket (F945) x 2

13mm Screw (F79) x 1

13mm Screw (F63) x 813mm Screw (F79) x 2

Hinge (F852) x 4

LHandle (F847a ) x 2

aLHandle Screw (F847b) x 4

Door Buffer (F137) x 4

Hinge Plate

(F853) x 4

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Choose which way

you would like the

doors to open

You can fit the doors to

the left side or right side.

If you would

like your doors

to open this

way, fit the

hinge plates to

the left side

If you would like

your doors to

open this way,

fit the hinge

plates to the

right side

Step 2

Step 3

Prepare the left side

a: Refer to step 1 and if

required, fit 4 hinge

plates onto the left

side , making sure

that the slot is facing

towards the front edge.

b: Screw 7 metal

dowels into the holes

shown on the left side

. .

Note: Tighten metal

dowels up fully against

the panels.

Fit a bracket to the

left side

Fit a bracket to the

left side , 10mm down

from the top edge, see

diagram.

Secure the bracket

using screw .

Note: The bracket must

be flush with the back

edge of the panel.

80%

x 3

10mm

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 4

Step 5

Prepare the right side

a: Refer to step 1 and if

required, fit 4 hinge

plates onto the right

side , making sure

that the slot is facing

towards the front edge.

b: Screw 7 metal

dowels into the holes

shown on the right side

. .

Note: Tighten metal

dowels up fully against

the panels.

Fit 2 brackets to the

right side

Fit a bracket to the

right side , 10mm

down from the top edge,

see diagram.

Secure the bracket

using screw .

Note: The bracket must

be flush with the back

edge of the panel.

Front

edge

Fit a bracket to the

left side

Fit a bracket to the

left side , 10mm down

from the top edge, see

diagram.

Secure each bracket

using screw .

Note: The bracket must

be flush with the edge of

the panel.

10mm

Finished

front edge

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Prepare the 3

horizontals

Insert 4 large locking

nuts into each

horizontal as shown.

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Tap 6 wooden dowels

into each horizontal

as shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Step 6

Step 7

Fit the 3 horizontals

to the right side

Push the horizontals

onto the right side .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

each horizontal .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 8

10mm

Prepare the plinth

Insert 2 large locking

nuts into the plinth

as shown.

Tap 2 wooden dowels

into the plinth as

shown.

Finished

front edge

Finished

front edge

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit the plinth to the

right side

Push the plinth onto

the right side , as

shown.

Use a screwdriver to

tighten the large locking

nut fitted to the

plinth , as shown.

Note: Turn the large

locking nut as far as

they will go - more than

1/2 a turn.

Step 9

Step 10

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 7 large

locking nuts fitted to

the 3 horizontals and

plinth .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit the back

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Slide the back

into the grooves along

the left and right

sides, as shown.

c: Secure the back

by tapping 4 nails

down into the back edge

of the top horizontal

and 4 nails into the

back edge of the bottom

horizontal .

Stand the unit up for

the next stage.

Step 11

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

1 2

Polystyrene

block

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Step 12

Step 13

Step 7

Fit the top

Note: To make it easier

to fit the top panel, place

polystyrene blocks from

the packaging

underneath the side

panels to raise the

assembly.

Position the top onto the

unit, making sure that

the back edge of the top

is flush with the back

edge of the sides.

Secure the top using

screw through the 2

brackets fitted at the top

edge of the side panels.

F100mm

100mm

500mm

Secure the unit to the

wall

Using the brackets

fitted to the back edge of

the sides and

screw the unit to the

wall.

Fixings are not supplied

as they will need to suit

the wall type, and the

length of screw will

depend on the distance

of the back of the Unit to

the wall.

Warning: Take

care when

drilling the wall

that you do not drill into

any pipes, wires etc. If in

doubt, consult an expert.

Ex 4

Fit the shelf studs

Choose the height

required for the 2

shelves.

For each shelf, push 4

shelf studs into the

holes in the side panels

. and .

1 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Osaka 2273237 Bedienungsanleitung

Argos

Argos Malibu Bedienungsanleitung

Argos

Argos OXFORD DINING FURNITURE Produktinformationsblatt

Argos

Argos Home Jenson Gloss Bedienungsanleitung

Argos

Argos 8757049 Bedienungsanleitung

Argos

Argos 620/4721 Bedienungsanleitung

Argos

Argos 609/1006 Bedienungsanleitung

Argos

Argos Monk’s Bench Style Linen Bin 832/5299 Bedienungsanleitung

Argos

Argos Gloss Double HOME Wall Cabinet Grey Bedienungsanleitung

Argos

Argos Designer 2 Tone Bedienungsanleitung

Argos

Argos 501-3298 Bedienungsanleitung

Argos

Argos Murano 332/6138 Datenblatt

Argos

Argos Capella 268/1647 Bedienungsanleitung

Argos

Argos Brooklyn 709/2688 Bedienungsanleitung

Argos

Argos Baby Amelie 226/1380 Bedienungsanleitung

Argos

Argos 600/0774 Bedienungsanleitung

Argos

Argos HOME Bedienungsanleitung

Argos

Argos Matrix Glass Nest Table Bedienungsanleitung

Argos

Argos Sywell 643/8047 Bedienungsanleitung

Argos

Argos Islington Installationsanleitung

Argos

Argos Osaka 2377889 Bedienungsanleitung

Argos

Argos Abigail 3 Bedienungsanleitung

Argos

Argos 332/5476 Bedienungsanleitung

Argos

Argos 460/9830 Datenblatt

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung