Argos Malibu 2 Drawer 3 Door Robe 257/6109 Bedienungsanleitung

MADE IN

BRITAIN

Issue2 - 25/11/13 - Cat codes were incorrect.

Dimensions

Width - 110cm

Depth - 49.5cm

Height - 181cm

Malibu - 2 Drawer 3 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 5 - 19/01/15

Important - Please read these instructions fully before starting assembly

ALR3024

257/6109

249/4298

257/7861

268/8554

248/7803

238/5792

Issue 3 - 01/04/14 - New version with metal runners, 3 piece drawer wraps etc...

Issue 4 - 03/09/14 - Changed Drawer Back description to W682-124BCK.

Round Back Holders have been changed to Oblong Back Holders.

Issue 5 - 19/01/15 - Overbalance bracket replaced with Strap.

Back Holders now shown fitted vertically.

Updated helpline number.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 76kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 1, 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

80% x 2

90% x 1

80% x 1

Top (D2837A)

(1071 x 494mm)

Base (D2842A)

(1071 x 494mm)

Drawer Base (T693-367)

(693 x 367mm) x 2

Drawer Back (W682-124BCK)

(682 x 124mm) x 2

Left Drawer Side (W370-124LH)

(370 x 124mm) x 2

Right Drawer Side (W370-124RH)

(370 x 124mm) x 2

Drawer Front (D2783A)

(710 x 156mm) x 2

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

overbalance protector kit

supplied or, an alternative fixing

method of your choice.

• Dispose of all packaging

carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

80% x 2

90% x 1

80% x 1

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Small Back (X1710-358)

(1710 x 358mm)

Large Back (X1710-734)

(1710 x 734mm)

18 19

Hanging Rail (FHR708)

(708mm long)

Left Side (D2838A)

(1808 x 496mm)

Shelf (D2843A)

(339 x 476mm) x 3

Right Side (D2839A)

(1808 x 496mm)

Plinth (D2844A)

(1071 x 92mm)

Back Rail (D2847A)

(716 x 92mm)

Upright (D2840A)

(1684.5 x 477mm)

Horizontal (D2841A)

(716 x 476mm)

Large Door (D2845A)

(1678 x 353mm)

Small Door (D2846A)

(1358 x 353mm) x 2

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Wooden dowel (F22) x 12

Metal dowel (F901) x 4

D E

G H I

Small locking

nut (F3) x 4

40mm Screw (F910) x 20

J K

Nail (F51) x 37

25mm Screw (F50) x 7

13mm Screw (F63) x 20

Rail holder

(F1014) x 2

Hinge (F522) x 9

Hinge plate (F523) x 9

Handle (F631) x 7

Nail screw (F277) x 5

Shelf stud (F110) x 12

Knock-in Peg (F171GY) x 8

Plastic Nail (F91) x 5

9mm Screw (F74) x 4

9mm Screw (F73) x 8

Wedgefix (F639) x 8

Drawer runner (F1004) x 4

Back holder (F276) x 5

*These can also be round

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

Tools required

Rule

Scissors

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

Square

mm 10 20 30 40 50 60 70 80 90 100

80% x 2

x 2

x 2 x 2

Note: Due to the manufacturing process, the holes for the

locking nut can be on either surface of the drawer sides.

Step 2

Prepare the 2 drawer

fronts

Screw 2 metal dowels

into each of the drawer

fronts .

Note: Tighten the metal

dowels up fully against

the panels.

Prepare the drawer

sides

Insert a small locking

nut into the hole

shown on the left drawer

side and the right

drawer side .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Assembly Instructions

Step 3

Step 4

x 2

Note: The locking nuts can be on either surface of the drawer sides.

Make sure that the small groove is on the inside, as shown.

Step 3

Attach the drawer

sides to the drawer

fronts

Push the left drawer sides

. and right drawer sides

. onto the back of the

drawer fronts .

Turn the small locking

nuts on the left

drawer side and right

drawer side .

Note: Turn the locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

Fit the drawer base

Slide the drawer base

down the grooves in the

drawer sides and

and down into the

groove in the drawer

front .

Step 5

Fit the drawer back

between the drawer

sides and .

Make sure that the

drawer base fits into

the groove in the drawer

back .

Hold the drawer back

in position and tap the

knock-in pegs

through the holes in the

drawer sides and .

2 3

x 2

80% x 2

Assembly Instructions

Step 6

80% x 2

90% x 1

80% x 1

10mm

Prepare the horizontal

Tap 2 wooden dowels

into the horizontal .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Finished

front edge

plain

chipboard

surface

Attach the handles

Attach 2 handles to

each of the drawer fronts

. using screws .

Note: Do not

overtighten the screw.

Step 7

Fit the wedgefixes

Turn the drawer

assemblies over and

slide 4 wedgefixes

into the front and back

grooves, as shown, and

tighten up the screws.

Step 8

x 2

80% x 2 1

Finished

front edge

Assembly Instructions

Step 9

Prepare the upright

a: Push a rail holder

into the upright .

Make sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Place 2 runners on

the upright as shown.

Slide back the top of

runner and use the 2nd

hole from the front to fit

the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the upright .

Tap 2 wooden dowels

into the left upright .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Fit 3 hinge plates onto

the upright making

sure that the slot is

facing towards the

finished front edge.

Finished

front edge

Finished

front edge

Finished

front edge

10mm

Finished

front edge

plain

chipboard

surface

Step 10

Fit the horizontal to

the upright

Push the horizontal

onto the upright and

secure it with 2 screws .

Finished

front edge

Assembly Instructions

Step 11

80% x 2

90% x 1

80% x 1

Prepare the top and

base

Tap 2 wooden dowels

into the top and the

base .

Finished

front edge

Finished

front edge

plain chipboard surface

Finished

front edge

plain chipboard surface

Step 12

Fit the top and base

to the upright

One at a time, push the

top and base

onto the upright and

secure each one with

2 screws .

6 7

Assembly Instructions

Step 13

Step 14

Fit the right side

Push the right side

onto the assembly

and secure it with 4

screws .

Step 15

Prepare the right side

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Finished

front edge

Prepare the back rail

and plinth

Tap 2 wooden dowels

into the back rail and

the plinth .

Plain

chipboard

surface

Plain

chipboard

surface

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos DALLAS 424/2833 Bedienungsanleitung

Argos

Argos 357/7097 Bedienungsanleitung

Argos

Argos AH TOBY 8545550 Bedienungsanleitung

Argos

Argos 618/0144 Bedienungsanleitung

Argos

Argos 906/4023 Bedienungsanleitung

Argos

Argos OSCAR 389/7612 Datenblatt

Argos

Argos SAN DIEGO 414/9376 Bedienungsanleitung

Argos

Argos Jakob 851/7739 Bedienungsanleitung

Argos

Argos Corners 9583119 Bedienungsanleitung

Argos

Argos Malvern 390/9641 Bedienungsanleitung

Argos

Argos Jenson Bedienungsanleitung

Argos

Argos Hygena Charlie 323/2349 Bedienungsanleitung

Argos

Argos San Diego 343/7058 Bedienungsanleitung

Argos

Argos Misaki 632/4546 Bedienungsanleitung

Argos

Argos Retro Pedestal 343/7395 Bedienungsanleitung

Argos

Argos Vancouver II 643/8157 Bedienungsanleitung

Argos

Argos Capella 268/1647 Bedienungsanleitung

Argos

Argos Matrix 609/0399 Bedienungsanleitung

Argos

Argos 932/6943 Bedienungsanleitung

Argos

Argos Malibu Bedienungsanleitung

Argos

Argos BASIC TALLBOY MIRROR CABINET 402/9166 Bedienungsanleitung

Argos

Argos Malibu 3 Drawer 2 Door Robe Bedienungsanleitung

Argos

Argos 869/6571 Bedienungsanleitung

Argos

Argos Tolga 2drw Bedside Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung