Argos Lucas 247/3965 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 100cm

Depth - 45cm

Height - 72cm

Lucas - Desk

Assembly Instructions - Please keep for future reference 247/3965

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 01/04/14

Important - Please read these instructions fully before starting assembly

Ruler - Use this ruler to help correctly identify the screws

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

ALR2989

247/6399

247/4476

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 19kgs. Please lift

with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: If there is any

chance of this unit being pulled

over by children etc. it is

recommended that the unit is

secured to a wall using suitable

fixings (not supplied).

• Dispose of all packaging

carefully and responsibly.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

Components - Panels

Please check you have all the panels listed below

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Left Side (D2911A)

(706 x 394mm)

Drawer Divider - D0034A

145 x 249mm

waterfall

Top (D2915A)

(1000 x 444mm)

Base (D2916A)

(349 x 392mm)

Upright (D2912A)

(706 x 394mm)

2Right Side (D2913A)

(706 x 394mm)

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Shelf (D2919A)

(349 x 373mm)

Drawer Base (T161)

(299 x 330mm)

Modesty (D2917A)

(602 x 157mm)

Drawer Front (D2914A)

(345 x 157mm)

Back (X725)

(626 x 373mm)

Plinth (D2918A)

(349 x 80mm)

Drawer Wrap (W161)

(943 x 95mm)

Please check you have all the fittings listed below

Tools required

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 2

Metal dowel (F901) x 8 Shelf stud (F110) x 4

Large locking

nut (F900) x 6

Small locking

nut (F3) x 2

40mm Screw (F910) x 10

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

LR (F601)

L (F600)

F599

Drawer stops (F599) x 2

Runners (F600) x 1 and (F601) x 1

19mm Screw (F461) x 2

Handle (F923) x 1

Nail (F51) x 12

Wedgefix (F639) x 2

Plastic Nail (F91) x 6

Assembly Instructions

Prepare the drawer

front and drawer wrap

a: Screw 2 metal dowels

. into the holes shown

on the back of the

drawer front .

Note: Tighten the metal

dowels up fully against

the panel.

b: Insert 2 small locking

nuts into the holes

shown on the drawer

wrap .

Note: The arrows on the

locking nuts must point

towards the hole in the

edge of the panel.

Assemble the drawer

a: Place the drawer

base into the narrow

slot on the drawer wrap

. . Fold the wrap

around the base.

b: Turn the drawer wrap

assembly over and push

it onto the back of the

drawer front .

Note: Turn the locking

nuts clockwise to

secure the panels - more

than 1/2 a turn.

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Attach the drawer

stops

Carefully break off the 2

drawer stops (F599) from

the pair of drawer

runners .

Push the drawer stops

fully through the drawer

wrap from the inside.

SNAP!

F599

Attach the handle

Attach the handle to

the drawer front using 2

screws .

Note: Do not

overtighten the screws.

F599

Step 3

Step 4

Step 5

Step 7

Fit the wedgefixes

Turn the drawer

assemblies over and

slide 4 wedgefixes

into the front and back

grooves, as shown, and

tighten up the screws.

x 4

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

LF600

Finished

front edge

Finished

front edge

Prepare the left side

and the upright

Separate the runners .

a: Push fit left runner

marked ‘L’ into the holes

shown on left side .

Note: Runners must be

be fitted flat against the

panel. If necessary

gently tap into final

position.

Insert 2 large locking

nuts into left side .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

b: Push fit right

runner marked ‘R’

into the holes shown on

upright .

Insert 2 large locking

nuts into the upright

. .

RF601

Prepare left and right

side

Separate runners .

a: Push fit 5 x left

runners marked ‘L’

into the holes shown on

left side .

Note: Runners must be

be fitted flat against the

panel. If necessary

gently tap into final

position.

Fit hinge plates

making sure that the slot

is facing towards the

finished front edge.

Push rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

b: Push fit 5 x right

runners marked ‘R’

into the holes shown on

right side .

Fit hinge plates

making sure that the slot

is facing towards the

finished front edge.

Push rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Step 6

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit the plinth to the

upright

Attach the plinth to

the upright using the

dowel already fitted and

secure with screw .

Fit the base to the

upright

Attach the base to

the upright using 2

screws .

Finished front edge

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Step 7

Step 8

Step 9

10mm

Finished

top edge

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit plinth to the

upright

Attach plinth to the

upright using the

dowel already fitted and

secure with screw .

Fit the left side

Attach the left side to

the base and plinth

using 3 screws .

Prepare the right side

Insert 2 large locking

nuts into the right

side .

Finished

front edge

Fit the modesty

2 people are needed

here

Attach the modesty

to the upright using 2

screws .

Support the modesty

until the right side has

been fitted in the next

step.

Step 10

Step 11

Step 12

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit the right side and

the plastic nails

2 people are needed

here

Attach the right side

to the modesty using

2 screws .

Tap 2 plastic nails

into the bottom edge of

the left side , upright

. and right side .

Prepare the top panel

a: Screw 6 metal dowels

. into the holes on the

top .

Note: Tighten the metal

dowels up fully against

the panel.

Step 13

Step 14

2 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Amersham 706/1262 Bedienungsanleitung

Argos

Argos 608/0811 Bedienungsanleitung

Argos

Argos Heathdon Habitat Lavendon 953/0083 Bedienungsanleitung

Argos

Argos HOME 607/7446 Bedienungsanleitung

Argos

Argos 157/7295 Bedienungsanleitung

Argos

Argos Nordic 3 Drawer Chest Bedienungsanleitung

Argos

Argos 484/2831 Bedienungsanleitung

Argos

Argos 460/9830 Datenblatt

Argos

Argos Verona 609/5033 Bedienungsanleitung

Argos

Argos Virgo Multi Media Storage Shelf Bedienungsanleitung

Argos

Argos Scandinavia 615/6374 Bedienungsanleitung

Argos

Argos HOME MID BACK GAMING CHAIR BLK 608/8734 Bedienungsanleitung

Argos

Argos Oakhampton 391/8333 Bedienungsanleitung

Argos

Argos Foley 333/7976 Datenblatt

Argos

Argos Iceland 178/6361 Bedienungsanleitung

Argos

Argos 875/4860 Bedienungsanleitung

Argos

Argos 601/5130 Bedienungsanleitung

Argos

Argos Kids Scandinavia XL Storage Box Bedienungsanleitung

Argos

Argos 501-3298 Bedienungsanleitung

Argos

Argos Dalton 246/6422 Bedienungsanleitung

Argos

Argos 603/4135 Bedienungsanleitung

Argos

Argos Monk’s Bench Style Linen Bin 832/5299 Bedienungsanleitung

Argos

Argos 875/4059 Bedienungsanleitung

Argos

Argos Designer 2 Tone Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung