Arkon MAGB1 Bedienungsanleitung

V1.3

List of Contents

1FEATURES 3

2SYSTEM INFORMATION 4

2.1 Supported Bands 4

2.2 Environmental 4

2.3 SIM Card 4

2.4 SMS 4

3INSTALLATION 5

3.1 SIM interface 5

3.2 SIM card installation 5

3.3 Antenna installation 6

3.4 3G/GPRS/GSM module installation, 6

3.5 3G/GPRS/GSM module battery 7

4SMS COMMANDS 8

4.1 Set Phone Number 8

4.2 Set GSM Service Center Address 8

5GPRS COMMANDS 9

5.1 Set Access Point Name 9

5.2 Set IP address 9

5.3 Set Port number 9

5.4 Set ID number for Arkon.Track 10

6COMMON COMMANDS 11

6.1 Set Sending Interval 11

6.2 Stop sending 11

6.3 Start sending 11

6.4 Set All 12

6.5 Get All 12

6.6 Set date and time 13

7SMS AND DATA FORMATS 14

7.1 SMS Data format 14

7.2TCP Data format 14

8EXAMPLES 15

8.1 SMS setting example 15

8.2 GPRS setting example 15

9TROUBLESHOOTING 17

10 FACTORY DELIVERED DEFAULT SETTINGS 18

10.1 Default settings of 3G/GPRS/GSM module 18

V1.3

1 FEATURES

• The MAGB1 sends the flow rate and the total volume by 3G/GPRS/GSM data at specific intervals.

•Specific interval of sending 3G/GPRS/GSM data is possible to setup, by sending an SMS.

• The SMS is sent to a specific phone number or SMS server (up to 3 phone numbers)

• The GPRS data are sent to a specific server (Arkon.Track) at a specific format using TCP port.

• Authorization is according to the unit number of MAGB1 transmitter and the SIM phone number.

• The user can send the SMS commands by a remote SMS server or a phone (5 minutes after plug

in battery).

V1.3

2 SYSTEM INFORMATION

2.1 Supported Bands

• Quad Band: 850/900/1800/1900 MHz

2.2 Environmental

• Operating temperature: -20 °C +60 °C

2.3 SIM Card

• 3.0V

• STK 3.1

2.4 SMS

• The SMS, is as defined within the GSM 850/900/1800/1900 digital mobile phone standard.

• A single short message can be up to 160 characters of ASCII text in length (7-bit coded).

• Message text can comprise words, numbers or an alphanumeric combination.

V1.3

3 INSTALLATION

•Open the transmitter.

•Unplug the battery.

•Deactivate the SIM card PIN lock.

•Delete all SMS messages in SIM memory.

•Insert the SIM card to the 3G/GPRS/GSM Module, see picture 1.

•Plug-in the 3G/GPRS/GSM module into the transmitter (into the GPRS Module slot, see

picture 3).

•Install external antenna to the 3G/GPRS/GSM Module.

•Plug-in the 3G/GPRS/GSM module battery.

•Plug-in the MAGB1 main battery

3.1 SIM interface

Before inserting or replacing SIM card –MAGB1 transmitter must be switched off!

Otherwise, MAGB1 transmitter, SIM card or GPRS module may get damaged!

The 3G/GPRS/GSM module incorporates a SIM interface, which conforms to the GSM 11.11

and GSM 11.12 standards that are based on the ISO/IEC 7816 standard. These standards define the

electrical, signaling and protocol specifications of a GSM SIM card.

The manufacturer does not supply the SIM card, which is mandatory for a connection to the

GPRS/GSM network! The SIM card may be purchased from your GSM (mobile) service provider!

3.2 SIM card installation

Insert the SIM card to the 3G/GPRS/GSM module according to picture bellow.

Picture 1. SIM card installation into the 3G/GPRS/GSM Module

V1.3

3.3 Antenna installation

Install antenna according to pictures below.

Picture 2. Antenna installation

3.4 3G/GPRS/GSM module installation,

Picture 3. Install 3G/GPRS/GSM Module into the transmitter

V1.3

3.5 3G/GPRS/GSM module battery

Picture 4. Install 3G/GPRS/GSM battery (the smaller one)

Picture 5. Plug-in the 3G/GPRS/GSM module battery

Warning electrostatic sensitive device.

Any connection or disconnection of any module has to be done with the battery switched off.

V1.3

4 SMS COMMANDS

Please note that all commands are case sensitive and have to be written in capital letters.

4.1 Set Phone Number

This command sets up the phone number and the 3G/GPRS/GSM module confirms the settings

immediately by SMS. This function works 15 minutes after plugging battery.

Query:

SET PHONE1 UNITNO NUMBER

SET PHONE2 UNITNO NUMBER

SET PHONE3 UNITNO NUMBER

UNITNO means the unit number of MAGB1 where the query is sent.

UNITNO is used for authorization.

NUMBER means requested phone number for sending interval or NONE erases existing phone number.

It is possible to set up to 3 phone numbers. 3G/GPRS/GSM module sends data from MAGB1 at specific

intervals to all 3 phone numbers. It is possible to set up just one or two phone numbers.

Syntax

Response example

Remarks

SET PHONE1 0123456 +420123456789

SET PHONE2 0123456 +987654321

SET PHONE3 0123456 NONE

PHONE1 0123456 +420123456789

PHONE2 0123456 +987654321

PHONE3 0123456 NONE

3G/GPRS/GSM module

sends data in specific

intervals to all 3 phone

numbers.

4.2 Set GSM Service Center Address

This command sets up the GSM service center address and the 3G/GPRS/GSM module confirms the

settings immediately by SMS. This function works 15 minutes after plugging battery.

Query:

SET GSMSERVICE UNITNO ADDRESS

UNITNO means the unit number of MAGB1 where the query is sent.

UNITNO is used for authorization.

ADDRESS means the phone number of the Service Center.

Syntax

Response example

Remarks

SET GSMSERVICE 01234567 +420603052000

GSMSERVICE 01234567 +420603052000

This command sets

the service center

address.

All phone numbers must be in international format (for example +420123456789)

V1.3

5 GPRS COMMANDS

Please note that all commands are case sensitive and have to be written in capital letters.

5.1 Set Access Point Name

This command sets the GPRS APN server name. The 3G/GPRS/GSM module confirms settings

immediately by SMS. This function works 15 minutes after plugging battery.

Query:

SET APN UNITNO APN

UNITNO means the unit number of MAGB1 where the query is sent.

UNITNO is used for authorization.

APN is Access Point Name - obtained from your GPRS SIM card provider (39 characters max)

Syntax

Response example

Remarks

SET APN 01234567 INTERNET.T-MOBILE.CZ

01234567 APN SET TO INTERNET.T-

MOBILE.CZ

This command sets

the APN to

internet.t-mobile.cz

5.2 Set IP address

This command sets the GPRS IP address of Arkon.Track server. The 3G/GPRS/GSM module confirms

settings immediately by SMS. This function works 15 minutes after plugging battery.

Query:

SET IP UNITNO XXX.XXX.XXX.XXX

UNITNO means the unit number of MAGB1 where the query is sent.

UNITNO is used for authorization.

xxx.xxx.xxx.xxx is the IP address of Arkon.Track server (or another server capable to process

incomming data)

Syntax

Response example

Remarks

SET IP 01234567 84.242.82.84

01234567 IP SET TO 84.242.82.84

This command sets

the IP address to

84.242.82.84

5.3 Set Port number

This command sets the GPRS TCP Port number of Arkon.Track server. The 3G/GPRS/GSM module

confirms settings immediately by SMS. This function works 15 minutes after plugging battery.

Query:

SET PORT UNITNO PORTNUMBER

UNITNO means the unit number of MAGB1 where the query is sent.

UNITNO is used for authorization.

PORTNUMBER is the TCP Port number of Arkon.Track server (or another server capable to process

incomming data). Port number set to 0 switches off GPRS communication.

Syntax

Response example

Remarks

SET PORT 01234567 5979

01234567 PORT SET TO 5979

This command sets

the TCP port to

5979

V1.3

5.4 Set ID number for Arkon.Track

This command sets the ID number for Arkon.Track server. The number needs to be unique. It needs to

start with 2, has 6 digits. The 3G/GPRS/GSM module confirms settings immediately by SMS. This

function works 15 minutes after plugging battery. This number is assigned during production!

Query:

SET ID UNITNO IDNUMBER

UNITNO means the unit number of MAGB1 where the query is sent.

UNITNO is used for authorization.

IDNUMBER is the ID of device for Arkon.Track server (or another server capable to process incomming

data). It is in format 2xxxxx

Syntax

Response example

Remarks

SET ID 01234567 200001

01234567 ID SET TO 200001

This command sets

the ID number to

200001

Inhaltsverzeichnis

Andere Arkon Zubehör Handbücher

Arkon

Arkon MAGB2 3G/GPRS/GSM Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung