Artidor AR-024 Bedienungsanleitung

User Manual

Explosion-safe occupancy sensor

Type series AR-024

II 3 G Ex ec mc IIC T6 Gc

II 3 D Ex mc tc IIIC T80ºC Dc

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 2 / 8

1. Safety Instructions

The AR-024 occupancy sensor is an explosion-safe product suitable for use in hazardous areas with explosion hazard

from flammable gases, vapors, mist and dust, classified as Zone 2 or Zone 22.

This manual must be read and understood for safe use of the occupancy sensor. All warnings and instructions must be

followed.

Installation must be carried out by personnel trained and qualified in explosion safety taking the instructions

mentioned on the equipment and in this manual into consideration. Local regulations that apply to the installation

must be followed.

Connect this equipment to the supply voltage for which it is designed.

Isolate electrical power to the occupancy sensor before electrical installation.

The protection degree against ignition “Encapsulation”, “Increased safety” and “Protection by enclosure” have

been applied to the apparatus. The enclosure may not be opened if the occupancy sensor is energized.

Installation of cables may not invalidate the “Protection by enclosure”, therefore only IP65 cable glands with the a

clamping size meeting the cable diameter should be used.

All unused openings should be plugged off in a properly closed and tight way.

Either decommission the occupancy sensor or do not use it when it is damaged.

During installation of the occupancy sensor national safety regulations must be observed.

Only use the occupancy sensor under the environmental conditions for which it is specified. Deviating

environmental conditions can contribute to damage to the equipment and may lead to possible danger to the life

of the user.

Do not use the occupancy sensor at temperatures deviating from the specified ambient temperature range.

Follow all instructions written on the equipment and as mentioned in this manual.

Repairs may only be carried out by the manufacturer or by a person appointed by the manufacturer.

Modifications to the equipment or changes to the design are not permitted.

The product may only be used for the function for which it is designed and shall be maintained in a good and

clean condition.

If these instructions are not followed, the explosion safety of the equipment cannot be guaranteed. The equipment

could then endanger the life of the user and could cause the ignition of an explosive atmosphere. Consequently, Artidor

as the manufacturer will waive any responsibility.

2. Description

The explosion-safe occupancy sensor AR-024 is based on passive infrared technology and capable of detecting

movements of heat sources. Thanks to the wide opening angle and its 10 m range, this sensor is suitable for

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 3 / 8

monitoring large areas. The occupancy sensor is designed for use inside large buildings for example warehouses and

combines energy saving and the protection of the environment in addition to convenient lighting.

Motion sensors switch the light depending on movements and the ambient light. Lighting will be switched off. The

sensor itself does not emit any radiation and is therefore called “passive”. Unlike motion sensors, occupancy sensors

can also switch off lighting if there is sufficient daylight, because of their advanced mixed light measurement (the

principle on which occupancy sensors are based). Do not install sensors near heat sources like air-conditioning units,

lights or radiators. The sensor electronics offers an potential free contact for switching up to 1,150 VA load.

The occupancy sensor is mounted on top of a coated aluminum housing. The explosion safety to gas and dust is

arranged by the appliance of protection degrees against ignition “encapsulation”, “molding”and “protected by

enclosure”.

The Artidor AR-024 occupancy sensor is certified in accordance with European Directive 2014/34/EU (ATEX 114) for

use in gas or dust hazardous areas and is CE marked.

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 4 / 8

3. Characteristics

The characteristics of the occupancy sensor can be summarized as follows;

Extended range of detection.

Coated aluminum housing and adjustable stainless steel mounting bracket.

Provided with two Ex e cable glands.

Manufactured on the basis of the European Directive 2014/34/EU (ATEX 114).

Suitable for use in gas and dust hazardous areas classified as zone 2 and 22.

Explosion safety category and protection degree against ignition applied:

II 3 G Ex ec mc IIC T6 Gc

II 3 D Ex mc tc IIIC T80˚C Dc.

Protection degree against the ingress of water and dust IP 65.

Suitable for indoor use.

4. CE - Marking

The occupancy sensor complies to the European Directives for EMC and ATEX and implicit to the Low Voltage

Directive. With regard to explosion safety the occupancy sensor has been designed and manufactured on the basis of

the essential health and safety requirements of European Directive 2014/34/EU (ATEX 114) relating to Group II

Category 3GD. Harmonized European construction standards have been applied fulfilling the essential requirements of

the directives.

5. Application

The explosion-safe AR-024 occupancy sensor has been designed for and is suitable for use in hazardous classified

areas due to flammable gases, vapors, mist, fibers and dust. Because it is explosion-safe and certified on the basis of

Group II Category 3GD of the ATEX Directive it is suitable for use in the following types of zones in explosion

hazardous areas:

for combustible gases, vapors and mist: zone 2

for combustible fibers and dust: zone 22.

6. Technical data

Explosion safety category: ATEX II 3GD

Protection against ignition: Ex ec mc IIC T6 Gc, Ex mc tc IIIC T80˚C Dc

Conformity: European Directive 2014/34/EU (ATEX 114) and 2014/30/EU (EMC)

Standards applied: EN 60079-0:2018, EN 60079-7:2015 / A1:2018, EN 60079-18:2015 / A1:2017 and

EN 60079-31:2014

Sensor: Passive infrared; 0,8 W power consumption

Mounting height: 2 –10 m

Range of coverage: An oval area of 24 x 44 m

Registration angle: Circular 360°

Dimmer setting: 10 –2,000 Lux

Preset time: 15 seconds –30 minutes

Supply voltage: 230 VAC ± 10%

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 5 / 8

Switch power AC1: 1,150 VA (resistive and light inductive loads)

Output: Potential free contact

Electrical connections: Terminals 8 x 2,5 mm²

Material: Die cast aluminum housing (RAL 7015, slate grey), cable glands nickel plated

brass

Entries: M16 or M20 cable glands (2x)

Sealed against moisture and dust: IP 65 according to EN 60529

Mounting bracket: Stainless steel mounting bracket, mounting holes Ø 6,5 (4x), distance 60 x 60 mm

Ambient temperature: -20 ˚C to +50 ˚C

Housing dimensions (L x W x H): 120 x 120 x 195 mm (including mounting bracket, excluding cable glands)

Sensor dimensions 65 x Ø98 mm

Weight: 1,860 g (incl. mounting bracket)

7. Marking and warning on the equipment

The marking label as shown below will be attached to the occupancy sensor:

8. Installation instructions

Installation of explosion-safe equipment such as this product must be carried out by personnel specially trained

and qualified to do this, following the relevant requirements of the installation standard EN 60079-14.

For the installation and use of this product the relevant safety regulations and also the generally recognized latest

state of the technology apply.

During assembly, care must be taken that the framework, screws and surface are strong enough to take the

weight of the occupancy sensor.

Isolate power from the electrical supply cable prior to installation.

Install the connection cable and make sure that it is protected from mechanical and chemical influences.

OCCUPANCY SENSOR

II 3 G Ex ec mc IIC T6 Gc Type: AR-024

II 3 D Ex mc tc IIIC T80ºC Dc 230 VAC, IP65

Cert. ARTIDOR 20ATEX9999X Year: 2020

TF & Serial No.: AS123456 -20 °C < Ta < +50 °C

ARTIDOR Explosion Safety B.V.

Emopad 38, 5663 PB Geldrop, The Netherlands, www.artidor.com

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 6 / 8

The occupancy sensor offers 8 connection terminals:

Power supply: Potential free contact:

L 230 VAC NO connection 1

N Neutral NO connection 2

PE Protective earth

R Connection for slave

S Switch for semi-automatic mode

9. Operating instructions

All setting can be done by use of the infrared remote control. The settings are explained in the OEM manual that is

supplied with the product.

Mechanical alignment: The detection area is oval shaped. Install the unit in such a manner that the markings on the

housing are positioned in the longitudinal direction of the area to be monitored. Do not install sensors near heat

sources like air-conditioning units, lights or radiators.

10. Troubleshooting

The functional indicators in the case of the ARTIDOR AR-024 (red and green LED‘s) have several functions.

Red and green LED indicating self-checking mode (over a period of 60 seconds following mains‘-supply lock-on)

Flashing at intervals of 1 second

EEPROM / memory empty

Flashing rapidly

EEPROM / memory contains information

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 7 / 8

Red LED as an indicator of status

Flashing irregularly

Movements are detected within the area of coverage

Flashing regularly

Sensor identifies bright, light off (dependent upon operating mode)

Not illuminated

Sensor identifies dark, light on (dependent upon operating mode)

Flashing extremely rapidly

Too bright / Too dark / Undefined

Red LED as an acknowledgement of receipt for commands from the remote control

Illuminated for 1 seconds

Signal validly received

Illuminated for 0.25 seconds

Not-accepted command, sensor blocked

Flashing extremely rapidly

Not-accepted command, occurs, for example, when an attempt is made to set a twilight-value that is too high or

too low

Red LED as an acknowledgement of receipt for commands from the remote control

Red and green LEDs flash 3x briefly every 5 seconds

Indicates semi-automatic mode

Red and green LEDs light up alternately

Determining the light value for automatic shutdown with sufficient daylight. (This is only indicated with a set lag

time of 30 minutes.)

11. Maintenance

For the maintenance of the AR-024 occupancy sensor the requirements as stated in EN 60079-17 apply. If the

occupancy sensor or the connection cable is no longer in good condition, very dirty or damaged, it must be repaired or

cleaned immediately. The power supply to the occupancy sensor must be switched off and may only be restored after

the maintenance has been carried out and approved.

The advised maintenance cycle for this occupancy sensor depends on its specific use and must therefore be agreed

upon with the user for the expected use.

12. Repair

If repairs are carried out in an incompetent manner, the explosion-safety of the occupancy sensor can no longer be

guaranteed. Therefore it is preferred that the occupancy sensor is returned to the manufacturer for repair.

13. Removal / re-use

The equipment can be completely processed as electronic waste. For processing regarding disposal or reuse of the

product and its packaging, national disposal and environmental laws and legislation must be taken into consideration.

User manual explosion-safe AR-024 occupancy sensor

Issue April 2020 8 / 8

This document is subject to change without notice.

Andere Handbücher für AR-024

Inhaltsverzeichnis

Andere Artidor Zubehör Handbücher

Artidor

Artidor AR-024 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung