Aruba AP-130 Series Bedienungsanleitung

Aruba AP-130 Series Access Point

Installation Guide

0510882-05 | July 2012 1

The Aruba AP-134 and AP-135 wireless access points support the IEEE 802.11n standard for high-

performance WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology and support

existing 802.11a/b/g/n wireless services. The AP-130 series access points work only in conjunction with an

Aruba Controller.

The Aruba AP-130 series access points provide the following capabilities:

Wireless transceiver

Protocol-independent networking functionality

IEEE 802.11a/b/g/n operation as a wireless access point

IEEE 802.11a/b/g/n operation as a wireless air monitor

Compatibility with IEEE 802.3af PoE and 802.3at PoE+

Central management configuration and upgrades through an Aruba Controller

Minimum Software Requirements

The AP-130 Series access point requires ArubaOS 6.1 or later.

Package Contents

AP-134 or AP-135 access point

Installation guide (this document)

9/16" Ceiling Rail Adapter

15/16" Ceiling Rail Adapter

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including

the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

Additional mounting kits for use with the AP-130 series access points are sold separately. Contact your Aruba sales

representative for details.

2 Aruba AP-130 Series Access Point | Installation Guide

Device Overview

Figure 1 AP-130 Series Access Points (AP-134 Shown)

LEDs

The AP-130 Series access point is equipped with five LEDs that indicate the status of various components of

the device.

PWR: Indicates the whether or not the AP-130 is powered on and its status.

ENET 0: Indicates the status and activity of Ethernet port 0

ENET 1: Indicates the status and activity of Ethernet port 1

11b/g/n: Indicates the status of the 2.4 GHz radio

11a/n: Indicates the status of the 5.0 GHz radio

For more information about the LEDs and their behavior, see Table 3 on page 10.

External Antenna Connectors

The AP-134 is designed for use with external antennas. The AP-135 is equipped with internal antennas. For

more information about antenna types and configurations, visit www.arubanetworks.com.

AP-134_003

134

Antenna Connectors (AP-134 Only)

LED Status Indicators

Aruba AP-130 Series Access Point | Installation Guide 3

Figure 2 AP-130 Series Rear

Console Port

Use the console port to connect to a terminal for direct local management.

Ethernet Ports

AP-130 Series is equipped with two10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired-network

connectivity port. These ports support IEEE 802.3af and 802.3at Power over Ethernet (PoE) compliance,

accepting 56VDC as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE)

such as a PoE midspan injector, or network infrastructure that supports PoE.

DC Power Socket

If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately) can be used to power the

AP-130 Series.

Reset Button

The reset button can be used to return the AP to factory default settings. To reset the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the AP without releasing the reset button. The power LED will flash within 5 seconds.

4. Release the reset button.

AP-134_002

CONSOLE ENET 1 ENET 0

Reset Button

DC Power Socket

Kensington Security Slot

When operating on 802.3af, only the port connected to power is usable. For example, if the source of power is

connected to ENET 0, ENET 1 will not work.

4 Aruba AP-130 Series Access Point | Installation Guide

The power LED will flash again within 15 seconds indicating that the reset is completed. The AP will now

continue to boot with the factory default settings.

Kensington Lock Slot

The AP-130 series is equipped with a Kensington security slot for additional security.

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement have been determined,

the Aruba Controller(s) must be installed and initial setup performed before the Aruba Access Points are

deployed.

For initial setup of the Controller, refer to the ArubaOS Quick Start Guide for the software version

installed on your controller.

Pre-Installation Checklist

Before installing your AP-130 series access point, be sure that you have the following:

For the AP-134: External antennas as specified in the network deployment plan

CAT5 or better UTP cable of required length

One of the following power sources:

IEEE 802.3af-compliant Power over Ethernet (PoE) source

IEEE 802.3at-compliant Power over Ethernet+ (PoE+) source

The POE source can be any power source equipment (PSE) controller or midspan PSE device

Aruba 12 VDC AP AC-DC adapter kit (sold separately)

Aruba Controller provisioned on the network:

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

FCC Statement: Improper termination of access points installed in the United States configured to non-US model

controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may

result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR

1.80).

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide for

details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous refer-

rer au ArubaOS User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Ein-

schränkungen finden Sie im ArubaOS User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per

avere informazioni detagliate sulle restrizioni.

Aruba AP-130 Series Access Point | Installation Guide 5

DHCP Server with vendor-specific options

Summary of the Setup Process

Successful setup of an AP-130 series access point consists of five tasks, which must be performed in this

order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs will be able to locate and connect

to the Controller when powered on.

Specifically, you must verify the following conditions:

When connected to the network, each AP is assigned a valid IP address

APs are able to locate the Controller (Mobility Controller Discovery)

Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the Controller.

Identifying Specific Installation Locations

You can mount the AP-130 series access point a ceiling rail (using the included adapter) or on a wall (using

the wall mount adapter, sold separately). Use the AP placement map generated by Aruba’s Airwave Virtual

RF software application to determine the proper installation location(s). Each location should be as close

as possible to the center of the intended coverage area and should be free from obstructions or obvious

sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation

and should have been accounted for during the planning phase and adjusted for in RF plan.

Unidentified Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the

installation phase is critical. Make sure that these sources are taken into consideration when you attach an

AP to its fixed location.

It is important that you verify the items listed under Pre-Installation Checklist before you attempt to set up and

install an AP-130 series AP.

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local broadcast

regulations. Specifically, access points must use channel assignments appropriate to the location in which the

access point will be used.

Aruba Networks, in compliance with governmental requirements, has designed the AP-130 series access points so

that only authorized network administrators can change the settings. For more information about AP configuration,

refer to the ArubaOS Quick Start Guide and ArubaOS User Guide.

6 Aruba AP-130 Series Access Point | Installation Guide

RF absorbers include:

Cement/concrete: Old concrete has high levels of water dissipation, which dries out the concrete,

allowing for potential RF propagation. New concrete has high levels of water concentration within the

concrete, blocking RF signals.

Natural Items: Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects: Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh

windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing

cabinets

Do not place an AP between two air conditioning/heating ducts. Make sure that APs are placed below

ducts to avoid RF disturbances.

RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Lunch rooms and call centers with cordless headsets

Aruba AP-130 Series Access Point | Installation Guide 7

Installing the AP

Using the Ceiling Rail Adapter

The AP130 series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling rails.

1. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed.

2. Place the adapter against the back of the AP with the adapter at an angle of approximately 30 degrees to

the tabs (see Figure 3).

3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 3).

Figure 3 Attaching the Ceiling Rail Adapter

4. If necessary, connect the console cable to the console port on the back of the AP.

5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-

degree angle to the ceiling tile rail (see Figure 4). Make sure that any cable slack is above the ceiling tile.

6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on the ceiling

tile rail.

Service to all Aruba Networks products should be performed by trained service personnel only.

Make sure the AP fits securely on the ceiling tile rail when hanging the device from the ceiling, because poor

installation could cause it to fall onto people or equipment.

AP-130_001

8 Aruba AP-130 Series Access Point | Installation Guide

Figure 4 Mounting the AP

7. On the AP-134, install the external antennas according to the manufacturer’s instructions, and connect

the antennas to the antenna interfaces on the AP.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and practices.

Ethernet Ports

The RJ45 Ethernet ports (ENET0 and ENET1) support 10/100/1000Base-T auto-sensing MDI/MDX

connections. Use these ports to connect the AP to a twisted pair Ethernet LAN segment or directly to an

Aruba Controller. Use a 4- or 8-conductor, Category 5 UTP cable up to 100 m (325 feet) long.

The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports have RJ-45 female

connectors with the pin-outs shown in Table 1.

AP-130_002

Aruba AP-130 Series Access Point | Installation Guide 9

Table 1 Ethernet Port Pin-out

Serial Console Port

The serial console port allows you to connect the AP to a serial terminal or a laptop for direct local

management. This port is an RJ-45 female connector with the pinouts described in Table 2. Connect this

port in one of the following ways:

Connect it directly to a terminal or terminal server using an Ethernet cable.

Use a modular adapter to convert the RJ-45 (female) connector on the AP to a DB-9 (male) connector,

and connect the adapter to a laptop using an RS-232 cable. See Figure 5 for connector details of the

adapter.

Table 2 Console Port Pin-out

Figure 5 RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion

Power Connection

The AP-130 Series has a single 12V DC power jack socket to support powering through an AC-to-DC power

adapter.

Connector Pin Signal

Name GE Connection FE

Connection PoE

1 BI_DA+ Bi-directional pair A+ RX+ POE negative

2 BI_DA– Bi-directional pair A– RX– POE negative

3 BI_DB+ Bi-directional pair B+ TX+ POE positive

4 BI_DC+ Bi-directional pair C+ Spare pair POE positive

5 BI_DC– Bi-directional pair C– Spare pair POE positive

6 BI_DB– Bi-directional pair B– TX– POE positive

7 BI_DD+ Bi-directional pair D+ Spare pair POE negative

8 BI_DB– Bi-directional pair D– Spare pair POE negative

Connector Pin Signal Name Function

3 TXD Transmit

4 GND Ground

5 GND Ground

6 RXD Receive

Pins not listed are not connected.

RJ-45 DB-9

Internal

Connections

TxD

GND

RxD

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

DB-9 Male

Pin-Out

TxD

RxD

Ground

Direction

Input

Output

If both POE and DC power are available, the AP uses POE even when there is not enough POE voltage available to

power the AP.

10 Aruba AP-130 Series Access Point | Installation Guide

Verifying Post-Installation Connectivity

The integrated LEDs on the AP can be used at this point to verify that the AP is receiving power and

initializing successfully (see Table 3). Refer to the ArubaOS Quick Start Guide for further details on

verifying post-installation network connectivity.

Configuring the AP-130

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are initially configured on the

Controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends that

provisioning settings be configured via the ArubaOS WebUI only. Refer to the ArubaOS User Guide for

complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured and stored on the

Controller. Network configuration settings are pushed out to the AP(s) but remain stored on the Controller.

Table 3 AP-130 Series LED Meanings

LED Color/State Meaning

PWR Off No power to AP

Green steady Power on, device ready

Green flashing Device booting, not ready

Red steady System failed to initialize

ENET 0

(100/1000 Mbps)

Green/Amber off No link

Green on 1000 Mbps link

Amber on 10/100 Mbps link

Green/amber blinking Link activity

ENET 1

(100/1000 Mbps)

Green/Amber off No Link

Green on 1000 Mbps link

Amber on 10/100 Mbps link

Green/amber blinking Link activity

11A/N Off 5 GHz radio disabled

Amber 5 GHz radio enabled in WLAN mode

Green steady 5 GHz radio enabled in 11n mode

Green flashing 5 GHz Air Monitor mode

11B/G/N Off 2.4 GHz radio disabled

Amber 2.4 GHz radio enabled in WLAN mode

Green steady 2.4 GHz radio enabled in 11n mode

Green flashing 2.4 GHz Air Monitor Mode

Andere Handbücher für AP-130 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Aruba Drahtloser Zugangspunkt Handbücher

Aruba

Aruba AP-375EX Bedienungsanleitung

Aruba

Aruba AP-334 Bedienungsanleitung

Aruba

Aruba IAP-367 Bedienungsanleitung

Aruba

Aruba 503H Bedienungsanleitung

Aruba

Aruba 630 Series Bedienungsanleitung

Aruba

Aruba 203H Bedienungsanleitung

Aruba

Aruba 300 series Bedienungsanleitung

Aruba

Aruba 560EX Series Bedienungsanleitung

Aruba

Aruba AP-100 Series Bedienungsanleitung

Aruba

Aruba 203H Bedienungsanleitung

Aruba

Aruba AP-205H Bedienungsanleitung

Aruba

Aruba AP-344 Bedienungsanleitung

Aruba

Aruba 518 Series Bedienungsanleitung

Aruba

Aruba Instant On AP22 Bedienungsanleitung

Aruba

Aruba 310 Series Bedienungsanleitung

Aruba

Aruba AP-375ATEX Series Bedienungsanleitung

Aruba

Aruba AP-303H Series Bedienungsanleitung

Aruba

Aruba AP-277 Bedienungsanleitung

Aruba

Aruba AP-504 RW Bedienungsanleitung

Aruba

Aruba 340 Series Bedienungsanleitung

Aruba

Aruba 200 Series Bedienungsanleitung

Aruba

Aruba AP-270-MNT-V1 Bedienungsanleitung

Aruba

Aruba RAP-5WN Bedienungsanleitung

Aruba

Aruba IAP-228 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung