Assa Abloy Corbin Russwin Access 800 Series Bedienungsanleitung

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

FM334 11/18

For CL33800 TCWI1 & TCIP1 Series

Installation Instructions

Cylindrical Lockset

Attention Installer

Access 800

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

TEST

FOR PROPER

OPERATION

BEFORE

CLOSING

DOOR

For installation assistance contact Corbin Russwin Inc., at 1-800-810-WIRE (9473)

1 2 3

ASSA ABLOY

Please read these instructions carefully to prevent missing important steps.

Please Note: Improper installation may result in damage to the lock and void the factory warranty.

Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.

Misalignment can cause premature wear and a lessening of security.

In U.S.:

Corbin Russwin, Inc.

225 Episcopal Road

Berlin, CT 06037 USA

www.corbinrusswin.com

In Canada:

ASSA ABLOY Door Security Solutions Canada

160 Four Valley Drive

Vaughan, Ontario, Canada L4K4T9

www.assaabloy.ca

WARNING

This product can expose

you to lead which is

known to the state of

California to cause cancer

and birth defects or other

reproductive harm. For

more information go to

www.P65warnings.ca.gov.

08/2018

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

1) Warning ................................................................................ 2

2) General Description/Speciﬁcations/Features .................... 3

3) CL33800 TWC1 Series Trim Product Illustration ................ 4

4) Installation Instructions ...................................................... 5

5) PIP (PoE) Wiring Options .................................................. 11

6) Hard Wiring Options .........................................................14

7) Operational Check ............................................................20

Table of Contents

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that the interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced TV technician for help

This Class B digital apparatus complies with Canadian ICES-003.

Warning: To comply with “Fire Listed” doors, only alkaline batteries must be used.

Changes or modiﬁcations to this unit not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

1) Warning

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

CL33800 WI1/IP1 Series Cylindrical Lock

Features

• WiFi IEEE 802.11 b/g/n enabled

• 2,400 users per lock

• 10,000 event audit trail

• Centralized lock management

• Real time door status monitoring

(Only applies when unit is hard powered)

• Supports HID 125kHz prox or 13.56 MHz iCLASS credentials (26-39 bit); supports CSN reads

for other common 13.56 MHz cards, including MiFare, DesFire, and Felica

• TCWI1 - Wireless

• DC9V, 1.5A (6 AA alkaline batteries or remote electrical power)

TCIP1 (PoE)

• Class 2 device, as deﬁned by IEEE 802.3af, requires a maximum of 7 watts over structured cabling

The Access 800 series lock is available with either Power over Ethernet (PoE) (TCIP1) or WiFi

(TCWI1) technology. The TCIP1 version utilizes existing infrastructure and IEEE 802.af Power over

Ethernet technology as a proven alternative to traditional access control installations. The TCWI1is

able to utilize existing wireless LAN (802.11b/g) in order to communicate with the access control

® ®

system. Credential options include either an HID 125 kHz Prox or 13.56 MHz iCLASS technology

reader; available with or without a keypad.

The Access 800 cylindrical lock may be used for both indoor and exterior applications. A protective

weather kit (provided with the unit) is recommended for exterior applications.

HID and iCLASS are registered trademarks of HID Global Corporation.

Speciﬁcations

• Latch –1/2" standard

• Inside lever retracts latch 3/4” throw ﬁre rated double doors

• Locks furnished for 1-3/4” to 2” doors

• (optional) (M16- preﬁx)

• U.L. Listed

• Deadlocking latch

• For 2-1/4" doors specify option D214

• Cylinder override

• Outside lever controlled by keypad, or key retracts latch

• TCIP1 (PoE) applications - wire from EAC Panel to door must be shielded with a drain (drain

terminated at EAC Panel controller)

2) General Descriptions/ Speciﬁcations/ Features

General Description

TCWI1 (WiFi)

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

REX

Connector

Weather Gaskets

3) CL33800 Series Product Illustration

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

Left Hand

Hinges Left.

Open Inward.

“LH”

Left Hand

Reverse Bevel

Hinges Left.

Open Outward

“LHR”

Right Hand

Hinges Right.

Open Inward.

“RH”

Right Hand

Reverse Bevel

Hinges Right.

Open Outward

“RHR”

Prep door according to supplied door marker.

1-1/2

Install latch bolt using

two # 8x3/4” screws.

7/8”

Hole for ribbon cable 1/8”

Dia. holes (2) required

Outside

of Door

Install strike plate using two #8-32x3/4” screws.

Screws

#8-32x3/4”

Centerline of

latch front

and strike

Fire Stop Plate required for

ﬁre rated doors

Slot

Attach ﬁre stop plate

using self tapping screws

#8-32x1/2” long for wood &

metal doors.

Conduit (optional) is available to

provide weather protection for

exterior applications. Install

conduit half with recessed panel

Not For Use On Fire Door visible

from outside of door.

and/or tapped

holes, 2 places

Latch bolt

door prep

Pre-drilled

Hole for

ribbon

cable

Outside

of Door

Lock body

hole

Non Fire Rated

Doors

C of 1-1/2 Dia

FOR

USE

FIRE

DOOR

NOT

4) Installation Instructions

Verify hand and bevel of door. Illustrations shown are as viewed from the outside

or secure side of opening.

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

5 Installing chassis to door

Feed lock body wire harness through 2-1/8” diameter lock body hole and then install

lock body into door.

Inside of door

Harness Slot

Tighten latch

assembly screws

Ensure lock body wire harness is positioned in the vertical slot. Attach inside cassette

housing and secure with screws.

Inside of Door

Feed wires and

connector if metal

door

Connect the REX connector on I/S

cassette to connector on lock body

Making certain that both wires are in

harness slot

DPS connector wire should come out

between edge of cassette.

Collar is used only with metal doors.

Door Position Switch

I/S Cassette

Housing

7 Install door position switch into hole on edge of door.

4) Installation Instructions

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

1A. For ﬁre rated doors feed ribbon cable connector and ground wire from outside

escutcheon

through the ﬁre stop plate.

1B. For non-ﬁre rated door applications, optional gaskets may be used as a weather seal

between the escutcheon and the door surfaces. An optional conduit is also available for

further protection. Feed ribbon cable connector and ground through the conduit (if used).

2. Slide the outside escutcheon over the lock and hold the escutcheon to the door surface.

Gasket

(optional)

4) Installation Instructions

Installation of Outside Escutcheon

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

GASKET APPLICATION:

Peel off the adhesive protective paper

from gasket. Feed keypad ribbon cable

and ground wire through gasket

opening as shown and ﬁrmly press

gasket to escutcheon, aligning edge of

gasket with the edge of the escutcheon.

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

1. Remove black battery cover from the escutcheon with high security T20 Torx bit provided.

2. Connect ground wire to terminal, connect keypad ribbon cable to controller, connect lock

body harness to motor connector, connect DPS, and connect remote power if applicable.

3. Feed all excess wire through inside door hole and/into inside escutcheon cavity, being careful

not to pinch wires.

NOTE: Connectors go on only one way. Do not offset connectors and be sure they are

completely seated.

4. Insert 2 #10 x 24 screws through top and bottom of inside escutcheon (use painted screw on

top) and thread into outside escutcheon. Straighten escutcheons and tighten securely, being

careful to avoid pinching wires.

Locate (2) oval head screws and insert

through the escutcheon into the outside

escutcheon. Tighten ﬁrmly.

*Use screw with painted white

head in top hole. Failure to do this

will result in damage to

electronics.

# 10 x 24 Oval

Head Screw

# 10 x 24 Oval

Head Screw

Motor Connector

Lock Body Harness

Gasket

(optional)

Keypad Ribbon

Cable

Ground Wire

Lock Body Harness

Cable

Ground Terminal

Remote Power Connector

Remote Power

Ground Terminal

DPS

Inside of the Door

Remote Power

(if applicable)

4) Installation Instructions

Installation of Inside Escutcheon and Electrical Connections

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

Keypad Ribbon

iCLASS

Cable

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

10 Installation and removal of Lever and Standard Cylinder

RELEASE

TOOL

RELEASE

TOOL

LEVER STYLE

PLAIN LEVER

CYLINDER LEVER

REMOVAL

PUSH RELEASE TOOL

Push release tool

Into release hole,

Remove lever

ROTATE KEY

Rotate key 45 clockwise

(from shed position),

Push in release tool into

Release hole, remove lever

Install Standard Cylinder

INSTALL

SLIDE LEVER OVER

Slide lever over

Lever catch

Pull on lever.

Make sure lever will

not pull off

INSERT KEY AND ROTATE

Insert key and rotate

45 (from Shed position),

slide lever on

Make sure lever will

not pull off

Make sure lock is unlocked.

A. Make sure cylinder tailpiece is aligned in same direction as cylinder bible. Slide cylinder all the

way into lever.

For 6 pin cylinder:Fold retainer at hinge and press ﬁt retainer halves together as shown.

For 7 pin cylinder: Break retainer at hinge and discard spacer section. Also remove black

cylinder spacer from inside of chassis rollback for clearance.

Standard Cylinder Tailpieces

ACTUAL

SIZE

SHOWN

7/8”

(22) 6 PIN 11/16”

(17)

7 PIN

4) Installation Instructions

CL33800 WI1/IP1 Series Cylindrical Lock

ASSA ABLOY

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Reproduction in whole or in part without the express written

permission of Corbin Russwin, Inc. is prohibited.

11 Installation (or Replacement) of Batteries, Battery Keeper and Cover

4) Installation Instructions

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

TEST

FOR PROPER

OPERATION

BEFORE

CLOSING

DOOR

CL33800 WI1/IP1 Series Cylindrical Lock

1. To install the batteries, ﬁrst remove the battery cover using the T20 bit provided (Fig. 11C).

2. Unscrew the bottom screw of the battery keeper and remove the battery keeper, being

careful not to break the tabs at top holding it in place. (Fig 11A)

3. Place (6) "AA" batteries in the compartment, being careful to align polarity properly (Fig.

11B)

4. Replace battery keeper being careful to engage tabs at top to hold it in place. (Fig 11A)

5. Attach battery cover to inside escutcheon making sure to line up tabs with retaining slots in

battery cover.

6. Secure with the security screw and T20 bit. (Fig 11C)

Security Screw

T20 Bit

Retaining

Slots

Tabs

Fig. 11C

Fig. 11B

Fig. 11A

Andere Handbücher für Corbin Russwin Access 800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy IP2326N Betriebsanleitung

Assa Abloy

Assa Abloy IKON VERSO CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 700 ML20700 TCPWI1... Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent IN220 Bedienungsanleitung

Assa Abloy

Assa Abloy 1584 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL654 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Luna Pro Bedienungsanleitung

Assa Abloy

Assa Abloy 179E Benutzerhandbuch

Assa Abloy

Assa Abloy Adams Rite 3000SE Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch NTB610 Technische Daten

Assa Abloy

Assa Abloy Sargent 52-4424 Leitfaden

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL654 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT IN Series Bedienungsanleitung

Assa Abloy

Assa Abloy CYE321 Bedienungsanleitung

Assa Abloy

Assa Abloy ML52RA Bedienungsanleitung

Assa Abloy

Assa Abloy Union CodeGUARD 5 Montageanleitung

Assa Abloy

Assa Abloy NORTON RIXSON M19 Bedienungsanleitung

Assa Abloy

Assa Abloy mFlipLock standard Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON DPA-12 Bedienungsanleitung

Assa Abloy

Assa Abloy ENTR Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Delayed Egress Bedienungsanleitung

Assa Abloy

Assa Abloy Yale PAS3621 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung