Assa Abloy H.e.s. 9200 Series Handbuch

Product Components

A 9200 Strike Body

B 9200 Cover

C 9200 1/8" Spacer

D 5/16"–18 x 1" Mounting Screws

E #12 Self Drilling Lockdown Screws

F #6-32 x 1/4" Cover Screws

G Door Stop/Rubber Bumper Kit

H Blind Nut

I Power Pigtail

J LM/LMS Pigtail (included

with LM and LMS only)

Specifications

Recommended Wire Gage For Distance

Voltage Current 200 Feet

or Less

200–300

Feet

300–400

Feet

12 VDC .5a 18 16 16

24 VDC .25a 22 22 20

UL1034

• Static Strength: 1500 lbs

• Dynamic Strength: 70 ft–lbs

• Endurance: 250,000 cycles

UL294 Performance Levels

• Destructive Attack: Level I

• Line Security: Level I

• Endurance: Level IV

• Standby Power: Level I

ANSI BHMA A156.31*

• Grade 1

• Function #: E09361

* For inductive kickback protection, consider using

with the HES 2005M3 SMART Pac®III or 2001M

Plug-in Bridge Rectifier with built-in MOV.

NOTE Installation wiring for the product and

wiring methods shall be in accordance with the

National Electrical Code, ANSI/NFPA 70.

9200 Series

Electric Strikes

Installation & Operating Instructions

8-3/8"

4-5/8"

9200W (WIDE)

9200N (NARROW)

Diagram 1

8-3/8"

4-5/8"

9200W (WIDE)

9200N (NARROW)

1 of 4

"X"

HEADER

INTERIOR FACE

OF DOOR SURFACE

IF "X" IS LESS THAN

3-1/4" ON FULL-GLASS DOORS OR

LESS THAN 2-1/2" FOR DOORS

WITH A 2" THICK TOP RAIL,

A SECURITRON UHB AND/OR HEB

WILL NEED TO BE INSTALLED

TO THE HEADER TO EXTEND

THE MOUNTING SURFACE

AND PROPERLY SUPPORT

THE ELECTRIC STRIKE

HEIGHT

STRIKE

WITH PENCIL

MARK THE EDGE

JUST IN FRONT

OF RAMPS

Preparing the Frame

Pre-Installation

Survey

1PERFORM an initial on-site survey to

determine the mounting method and

review the installation plan. Diagram 2

Take the following into consideration:

• Physical strength of mounting

areas should be strong enough

to meet or exceed the holding

force of the existing strike.

• Placement of the strike wiring

and protection from potential

damage due to intruders or

vandal’s external attack.

2MEASURE height of existing strike. Use

included shim if height is 3/4". Do not

use shim if height is 5/8".

Diagram 3

3MARK the front edge of the existing

strike for proper alignment of

the new strike. Diagram 3

Preparing the Strike

Factory

Configuration

The HES 9200 Electric Strike is

pre-configured from the factory

for FAIL SECURE operation

as shown. Diagram 1a

The HES 9200 Electric Strike

can be converted for FAIL SAFE

operation as shown. Diagram 1b

SELECT correct Door Stop length

for application. Long stop for use

with full glass doors without a rail.

Short for use with solid door or

glass door with rail. INSTALL Door

Stops with Rubber Bumper.

Diagram 1a

Diagram 1b

"X"

HEADER

INTERIOR FACE

OF DOOR SURFACE

IF "X" IS LESS THAN

3-1/4" ON FULL-GLASS DOORS OR

LESS THAN 2-1/2" FOR DOORS

WITH A 2" THICK TOP RAIL,

A SECURITRON UHB AND/OR HEB

WILL NEED TO BE INSTALLED

TO THE HEADER TO EXTEND

THE MOUNTING SURFACE

AND PROPERLY SUPPORT

THE ELECTRIC STRIKE

HEIGHT

STRIKE

WITH PENCIL

MARK THE EDGE

JUST IN FRONT

OF RAMPS

Diagram 2

Diagram 3

2 of 4

Preparing the Frame (CONTINUED)

If replacing the existing strike the HES 9200

should mount directly to the header using

the existing strike mounting holes. Only

wire holes will need to be drilled. If it is a

new install, use the following steps:

1MARK centerline of latchbolts to header.

2PUNCH, DRILL the marked mounting

holes as required. Diagram 4

3PUNCH, DRILL the marked wire access

holes as required. Diagram 4

4 INSTALL mounting Blind Nuts (if needed).

13"

1-11/16"

1-5/8

1/4"

3X 5/16-18 UNC

1-9/16"

1-7/8"

5-9/16" 5-9/16"

4-7/8"

INTERIOR FACE OF

3/4" THK GLASS

INTERIOR FACE OF

1/2" THK GLASS

OUTLINE

STRIKE

CENTERLINE OF LATCHBOLTS

1/2"

9200W WIRE

PASS-THRU

1/2"

9200N WIRE

PASS-THRU

Diagram 4

Connector Pin-Outs If using the C1 — Latchbolt Monitor (LM) or

C1 — Latchbolt and Strike Monitor (LMS), use

the LM/LMS 6-pin Plug In Connector (pigtail)

and REFER to chart to complete wiring.

NOTES: For double doors the LM/LMS states will

only show secure when BOTH doors (LM) and

electric strike (LMS) are secure. See Chart below.

“Secure” means latch is detected & secured

within strike pocket for LM and the strke

is also in a locked state for LMS.

C1 — Latchbolt Monitor

WHT Common

ORG Normally Closed

GRN Normally Open

C1 — Latchbolt and Strike Monitor

BRN Common

BLU Normally Closed

YEL Normally Open

C2 — 12/24 V Power

BLK 12/24 V–

RED 12/24 V+

LM Input LM Output Wire Condition

Door 1 Door 2 LM State Open Closed

Unsecure Unsecure Unsecure GRN & WHT ORG & WHT

Secure Unsecure Unsecure GRN & WHT ORG & WHT

Unsecure Secure Unsecure GRN & WHT ORG & WHT

Secure Secure Secure ORG & WHT GRN & WHT

LMS Fail Secure

LMS Input LMS Output Wire Condition

Solenoid 1 Solenoid 2 LMS State Open Closed

Retracted Retracted Unsecure YEL & BRN BLU & BRN

Extended Retracted Unsecure YEL & BRN BLU & BRN

Retracted Extended Unsecure YEL & BRN BLU & BRN

Extended Extended Secure BLU & BRN YEL & BRN

LMS Fail Safe

LMS Input LMS Output Wire Condition

Solenoid 1 Solenoid 2 LMS State Open Closed

Retracted Retracted Secure BLU & BRN YEL & BRN

Extended Retracted Unsecure YEL & BRN BLU & BRN

Retracted Extended Unsecure YEL & BRN BLU & BRN

Extended Extended Unsecure YEL & BRN BLU & BRN

Finishing the Installation

1Connect power pigtail and LM/LMS pigtail

(if equipped) wires to existing wiring

coming out of the frame. Diagram 5

ORG

WHT

GRN

BLU

BRN

YEL

RED

BLK

Diagram 5

3 of 4

Printed in the U.S.A.

Patent pending and/or patent www.assaabloydss.com/patents

permission of Hanchett Entry Systems, Inc. is prohibited. 3089006.001_1

techsupport.hes@assaabloy.com

800 626 7590 | hesinnovations.com

Finishing the Installation

1ELECTRICALLY CONNECT the 9200

(9200W Shown) to the pigtails,

and ATTACH the electric

strike to the header using the

5/16"-18 x 1" mounting screws

provided. Diagram 6

2ALIGN front edge of latchbolt ramps

with marked line from Diagram 3.

3CHECK the latchbolt interaction

with the keepers to ensure proper

engagement and clearance. If front

and back, MACRO adjustment

is needed, ADJUST the strike

and RETIGHTEN the three

5/16"-18 x 1" mounting screws.

4Check door play and adjust Door

Stops as needed for MICRO

adjustment using a slotted driver on

the back of the strike. Diagram 7

5ADJUST the latchbolt depth into

the keeper pocket per the exit

device manufacturer’s instructions.

Ensure the latchbolt clears the

keeper pocket when the exit

device bar is manually depressed.

6TEST the mechanical and electrical

operation to confirm the ability to

release, capture and detect the door.

7LOCKDOWN Door Stop with

included 8-32 set screws.

(5/64 Allen Wrench)

Diagram 8

8LOCKDOWN the front and

back adjustment using the

#12 self threading screws

illustrated. Diagram 9

9INSTALL the cover, and SECURE

in place using the #6-32 x 1/4"

Cover Screws. Diagram 10

10 Finished Installation. Diagram 11

Diagram 6

As required.

See Diagram 3. Diagram 7

Diagram 8

Diagram 9

Diagram 10

Diagram 11

CAUTION Take care to not damage any of the

flex cables or printed circuit boards and remove

all metal debris before installing the cover.

4 of 4

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Hes 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Nexion Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio C100 V3 Bedienungsanleitung

Assa Abloy

Assa Abloy ADAMS RITE 4300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale eBoss 886F Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD226 Technische Daten

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC256 Technische Daten

Assa Abloy

Assa Abloy effeff MAGAC-L Series Bedienungsanleitung

Assa Abloy

Assa Abloy ENTR Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson 73ER Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT KP8977 Leitfaden

Assa Abloy

Assa Abloy Yale YDM3115A Bedienungsanleitung

Assa Abloy

Assa Abloy DC423.2 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON M19 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 1489 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON 93 Bedienungsanleitung

Assa Abloy

Assa Abloy CLIQ eCLIQ Connect key Bedienungsanleitung

Assa Abloy

Assa Abloy 8788 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 5300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 843ZY-1 Q41 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 332 E91 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Selector Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung

Assa Abloy h.e.s. 9200 Series Handbuch

Beliebte Türschloss Handbücher anderer Marken