Assa Abloy ADAMS RITE 4300 Series Bedienungsanleitung

1 80-0180-418, Rev D

4600 Heavy Duty Designer Deadlatch Handles With

4300, 4500, and 4900 Series Deadlatches

Installation Instructions

TABLE OF CONTENTS

Tools and Equipment Needed ........................................................................................................ 2

Preparing the Stile........................................................................................................................... 2

Offsetting the Escutcheon for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset........................ 4

Optional Monitoring Switch ............................................................................................................. 4

Installing Trim to Stile...................................................................................................................... 5

Installing the Handle........................................................................................................................ 6

Determining and Changing the Handing Configuration.................................................................. 7

Changing the Handing of the 4581 Cam Disc................................................................................. 7

Phoenix, AZ

Tel: 1-800-872-3267

Mon-Fri: 6:00am - 4:00pm PDT

Fax: 1-800-232-7329

www.adamsrite.com

2 80-0180-418, Rev D

IMPORTANT: This product must be installed according to all applicable building and

life safety codes!

Tools and Equipment Needed

The following common hand tools are needed for installation:

• 7/32” [5.56 mm], 1/4” [6.35 mm], and 3/8” [9.53 mm] drill bits

• 3/32” [2.38 mm] Allen Wrench

• Center punch

• Drill

• Flat tip screwdriver

• Phillips screwdriver

• Pencil

Preparing the Stile

NOTE: Figure 1, “Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset,

Single Lever,” and Figure 2, “Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single

Lever,” provide illustration for the following steps.

1. IF using a 1-1/8” [28.58 mm] backset,

THEN MARK a vertical reference line 5/32” [3.97 mm] behind the backset centerline.

2. APPLY the stick-on template over the cylinder backset centerline reference 5/32” [3.97 mm]

offset to clear the stop on the frame for a 1-1/8” [28.58 mm] backset.

3. CENTERPUNCH all holes.

4. DRILL holes at center punch locations.

5. REMOVE the template.

3 80-0180-418, Rev D

Figure 1. Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset, Single Lever

Figure 2. Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single Lever

Inches [Millimeters]

4 80-0180-418, Rev D

Offsetting the Escutcheon for 31/32” [24.61 mm] and

1-1/8” [28.58 mm] Backset

1. LOOSEN the two #4-40 x 1/4” flat head screws securing the adjustable cover on the back of

the trim cartridge until the cover can be slid (see Figure 3, “Adjustable Cover and Trim

Cartridge”).

2. PUSH the adjustable cover toward the nose edge of the door until it stops (see Figure 3).

3. TIGHTEN the two #4-40 flat head screws to secure the adjustable cover in place.

Figure 3. Adjustable Cover and Trim Cartridge

Optional Monitoring Switch

NOTE 1:Monitored trim contains an internally mounted switch (see Figure 4, “Optional Monitor

Switch”), secured with two M1.6 x .35 mm Phillips pan head screws. The switch is

activated when the handle is rotated to the UNLOCK position.

NOTE 2: All unused leads from the monitor switch must be terminated.

Figure 4. Optional Monitor Switch

5 80-0180-418, Rev D

1. WIRE the optional monitor switch in accordance with Table 1, “Wire Colors and Maximum

Switching Current,” and Figure 5, “Example Wiring Diagram with N.O. Monitoring.”

Table 1. Wire Colors and Maximum Switching Current

Wire Color Label

Black Common Contact

White Normally Open Contact (N.O.)

Red Normally Closed Contact (N.C.)

Maximum Switching Current

(choose N.O. or N.C. for monitoring) 0.1A at 125 VAC/30 VDC

Figure 5. Example Wiring Diagram with N.O. Monitoring

Installing Trim to Stile

1. INSTALL rivnuts.

2. INSTALL the 4581 Cam Plug into the 4300, 4500, or 4900 deadlatch, and SECURE with the

set screw on the latch.

3. INSERT the drive spindle into the trim body prior to mounting.

4. MOUNT the cover plate (not required for 1-1/2” backset) and the trim body to the stile using

two #10-32 x 7/8” flat head screws.

5. SLIDE the cover onto the trim body from the top.

NOTE: The groove on the shaft faces opposite to the latch bolt.

6. INSERT the shaft through the hole on the cover and the output on the trim body.

7. TIGHTEN the set screw with a 3/32” Allen wrench to secure the shaft (see Figure 6,

“Installing Trim to Stile”).

8. INSTALL the top cap using two #4-40 x 1/4” flat head screws (see Figure 6).

9. PUSH the cover up flush with the top cap, and INSTALL the bottom cap using a #6-32 x 1/4”

flat head screw (see Figure 6).

6 80-0180-418, Rev D

Figure 6. Installing Trim to Stile

Installing the Handle

1. INSERT washer and then INSERT hub

over the shaft, as required (see Figure 7,

“Installing the Handle”).

Figure 7. Installing the Handle

2. INSTALL the handle over the hub with the

hole aligned with the hole on the hub (see

Figure 7).

NOTE: The shaft detent should be aligned

with the locking screw.

3. SLIDE the handle in until it rests against

the trim cover.

Using a 1/8” Allen wrench, TIGHTEN the

lock screw to secure the handle to the

shaft (see Figure 7).

7 80-0180-418, Rev D

Determining and Changing the Handing Configuration

1. DETERMINE the current handing configuration(see Figure 8, “Handing Configuration”).

Figure 8. Handing Configuration

NOTE: During the next step, it is necessary to hold the monitor slide down to keep it from

popping out of place by the slide return spring.

1. IF a change of handing is required,

THEN PERFORM the following.

a. REMOVE both #4-40 x 1/4” screws and REMOVE the cover (see Figure 8).

b. REMOVE and FLIP the direction rack, ensuring the drive gear stays in position (see

Figure 8).

c. INSTALL cover.

d. SECURE cover using the two #4-40 x 1/4” screws

Changing the Handing of the 4581 Cam Disc

NOTE: Figure 9, “Changing the Handing of the 4581 Cam Disc,” provides an overall view for

the steps in this section.

Figure 9. Changing the Handing of the 4581 Cam Disc

8 80-0180-418, Rev D

1. DEPRESS the rear push cap.

2. While holding the rear push cap, SLIDE

the eagle beak cam down and out of

the front push cap and the dowel pin.

3. FLIP the eagle beak cam to the other

side, and SLIDE it in the dowel pin and

up to the front push cap.

4. Release the rear push cap to complete

the changing hand operation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Lockwood 530 DX Series Bedienungsanleitung

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy IKON VERSO CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy AUE100 Aperio Bedienungsanleitung

Assa Abloy

Assa Abloy HES 9400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDM3115A Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YMI70A Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 1220 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 8788 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy HES 9400 Betriebsanleitung

Assa Abloy

Assa Abloy Harmony H1 Bedienungsanleitung

Assa Abloy

Assa Abloy MSL mFlipLock standard Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff EX118P Series Bedienungsanleitung

Assa Abloy

Assa Abloy ML55 PA Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDLL/BLK Fehlerbehebungshandbuch

Assa Abloy

Assa Abloy 179A Benutzerhandbuch

Assa Abloy

Assa Abloy Lockwood Onyx 9A1A2/5PBLK Bedienungsanleitung

Assa Abloy

Assa Abloy effeff ANYKEY Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung