Assa Abloy Sargent 10G13 Bedienungsanleitung

INSTALLATION INSTRUCTIONS FOR

10 Line Lever Lock (Patents Pending)

For installation assistance, contact SARGENT at 800-727-5477

www.sargentlock.com

Door Preparation

IMPORTANT:

Fold template onto high

edge of door bevel

38" fr

Finished Floor

Template

Door

Bevel

DOOR

FRAME

Backset

must match lock

(2-3/8" or 2-3/4")

• All doors should be properly reinforced for lock support. If support is not provided, contact door manufacturer.

• For all metal door preparations use template A4375, EXCEPT for functions 10G70 or 10G71 which uses template 4409

(provided), or functions 10U93, 10U94 and 10U94-2 which require template A4375.

• For all wood door preparations use template A6719, EXCEPT for functions 10G70 & 10G71 which uses template 4409

(provided), or functions 10U93, 10U94 and 10U94-2 which requires template A4375.

• Template information is available on our website, [email protected].

Strike

IMPORTANT: Deadlocking latch must

stop on strike when door is closed

• Final Door Prep • Frame Prep for Strike

10 11

Parts

1. Inside lever

2. Scalp (2)

3. Screws – mounting plate

(2) #6 x 3/4” self-tapping

4. Spacer bushing (2)

5. Inside rose assembly

6. Screws – through-bolt

(2) #10-32 x 1-1/4”

7. Lockbody

8. Outside rose assembly

9. Cylinder spacer

Tools

#2 Phillips screwdriver

Push pin (provided)

7/16” drill bit

1/8” drill bit

2-1/8” bore

1” bore

10. Cylinder

11. Outside lever

12. Key

13. Push pin

14. Latch

15. Screws – latch & strike

(4) #8-32 x 3/4”

16. Strike

17. Strike box

Screws (2)

#8-32 x 3/4"

Centerline of

latch front and

strike

Outside of Door

(secured side)

Inside of Door

• Mark and Drill Holes

2-1/8"

(54mm)

hole

5/32"

(4mm)

1-1/8"

(29mm)

2-1/4"

(57mm)

7/16" (11mm) hole

(25mm)

hole

* Used with 68 Function only

Preset LockLatch Installation

Door

frame

2-FRONT

Screws (2)

10-32 x 1-1/4"

Screws (2)

#6 x 3/4"

Scalp to be removed with flat

bladed screwdriver at notch

Test

for proper

operation

before

closing

door

Through-bolt

holes

Mounting plate

with through-bolts

Spacer bushing

Preset thrubolt locations –

for different locations see

instructions to the right

Outside

of Door

Preset thrubolt locations –

for different locations see

instructions to the right

Outside

of Door

Install loosely;

tighten after step #3

Screws (2)

#8-32 x 3/4”

Please note: Doors without a beveled edge need to be

adjusted to center the latch - adjust per step 2A.

Outside

of Door

1-3/4" thick door

2" thick door

•Through-bolt Location – 12 and 6 o’clock

•Door Thickness – 1-3/4” thick

• See Step 2A for other door conditions

A7133J © SARGENT Manufacturing Company

• Remove – outside lever (usually keyed), scalp and spacer bushing

• Rotate – mounting plate to either align with through-bolt holes in door

or adjust for proper door thicknesses (see markings on through-bolt)

• Reinstall – spacer bushing (to align with back of lever), scalp and lever

Through-bolt and door thickness adjustment other than preset

Lever and Cylinder Removal

Standard Cylinder Installation

Interchangeable or Removable Core Installation

Rotate key 45ϒ

and hold

Depress lever retainer

with push pin tool

Control key*

Rotate key 45ϒ

and hold

Depress lever retainer

with push pin tool

Control key*

Remove/Reuse

6 Pin Tailpiece

Plastic Core

Construction

Core

7-pin –

in box

6-pin –

in core

Keyed

Cylinder

Keyed

Cylinder

New Cylinder

Washers

(only 30-prefix)

Cylinder

Outside

lever

Key

Cylinder

spacer

IMPORTANT:

Before cylinder installation 10G16, 10G30,

10G37, 10G38 and 10G54 functions

lock, must be timed/preset by rotating

cam (within the the lever support tube)

completely counterclockwise.

• Remove cylinder and tailpiece, using

control key (stamped “C”)

• Insert Phillips #2 screw driver into

cylinder opening making contact with

lever retainer.

• Pull lever retainer horizontally towards

door hinge and remove lever.

*Note- 1 Bitted cylinders utilize a control

key cut 113511

Correct key orientation

during assembly

• IMPORTANT:

Remove tailpiece from construction

core and insert into new cylinder

• Install Cylinder

Insert cylinder with control key (stamped “C”)

into lever; rotate 15 degrees and remove key

• Remove construction core

or plastic core

If keyed – use Control Key

(stamped “C”) rotate 15

degrees and pull

Remove/Reuse

6 Pin Tailpiece

Plastic Core

Construction

Core

7-pin –

in box

6-pin –

in core

Keyed

Cylinder

Keyed

Cylinder

New Cylinder

Remove/Reuse

6 Pin Tailpiece

Plastic Core

Construction

Core

7-pin –

in box

6-pin –

in core

Keyed

Cylinder

Keyed

Cylinder

New Cylinder

Remove/Reuse

6 Pin Tailpiece

Plastic Core

Construction

Core

7-pin –

in box

6-pin –

in core

Keyed

Cylinder

Keyed

Cylinder

New Cylinder

Remove/Reuse

6 Pin Tailpiece

Plastic Core

Construction

Core

7-pin –

in box

6-pin –

in core

Keyed

Cylinder

Keyed

Cylinder

New Cylinder

Remove

Construction

Core

Install

New/Final

Cylinder

Lever retainer

Standard Cylinder

Interchangeable and Removable Core Cylinder

Install 10U94/10U94-2

Remove 10G13

A7133J © SARGENT Manufacturing Company

• Remove inside (non-rigid) lever with standard

push pin

• Insert long push pin into inside lockbody tube

and push to release spring loaded lever catch

plug assembly for the outside lever

• Remove the outside lever with lever catch plug

assembly attached

• Power Required: 24Volt DC, .25 amps,

wiring information provided

• Wires must be protected from

abrasion

• Important- See correct door template

4409 provided or on the

website at [email protected].

Function Description:

10G70 Fail Secure

Power OFF unlocks outside lever

Power ON locks outside lever

Key retracts latch at all times

10G71 Fail Secure

Power ON unlocks outside lever

Power OFF locks outside lever

Key retracts latch at all times

2-FRONT

Screw

1/4 x 20 Cup

washer

Screws (2) #6 x 3/4"

Scalp to be removed

with flat bladed screwdriver

2 holes to align with

2 tabs on rose

Rose

Install 10U93

Install 10G70 & 10G71

Screw

1/4 x 20

Cup

washer

Backset

1-1/8" 1/8" x 3/16" deep

Hole

5/16"

dia.

Screws (2) #6 x 3/4"

Scalp to be removed

with flat bladed screwdriver

Screws (2) 10-32 x 1-1/4"

Screws (2)

#8-32 x 3/4"

Tab

2 holes to align with

2 tabs on rose

Rose

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Yale eBoss 886F Series Bedienungsanleitung

Assa Abloy

Assa Abloy 81 C Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL574 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDM3115A Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin TL3700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Code Handle Handbuch

Assa Abloy

Assa Abloy RIXSON 93 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Conexis L1 Bedienungsanleitung

Assa Abloy

Assa Abloy DC6210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED3400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDD724A Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 309 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy Corbin Russwin MP9800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ENTR Bedienungsanleitung

Assa Abloy

Assa Abloy 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Delayed Egress Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 530 DX Series Bedienungsanleitung

Assa Abloy

Assa Abloy ADAMS RITE 4300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron DSB Series Bedienungsanleitung

Assa Abloy

Assa Abloy EL580 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung