Assa Abloy SARGENT 10X Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com

A8286 04/21

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

Installation Instructions

10X Line Cylindrical Lockset

Installation Instructions

• #2 Phillips screwdriver

2Package Contents

1Tools Required

• Push pin (provided) • 1/8" drill bit• 7/16" drill bit • 2-1/8" Bore •1" Bore

• 5/32" drill bit

Fig. Description

1 Inside lever handle

2 Rose/Scalp (2)

3 Screws - latch (2) #8-32 x 3/4"

4 Inside spring housing assembly

5 Screws - through-bolt (2) #10-32 x 1-1/4"

6 Lockbody assembly with mounting plate

7 Outside spring housing assembly

8 Cylinder spacer

9 Cylinder

10 Outside lever handle

11 Key

12 Push pin

13 Latch

14 Screws - strike (2) #12-24 x 3/4"

15 Strike

16 Strike box (Optional)

3Door Preparation

DOOR

FRAME

Desired

height

above

floor

Template

Backset must

match latch Door bevel

Figure 1

7/16" (11mm) hole

2-1/8"

(54mm)

hole

1-1/8"

(29mm)

2-1/4"

(57mm)

1" (25mm)

hole

5/32" (4mm)

2-3/4"

(70 mm)

Figure 2

IMPORTANT

• The accuracy of door preparation is critical for proper functioning and security of this lever handle lock. Misalignment can

cause premature wear and a lessening of security.

• Be sure to verify backset before marking and drilling door.

IMPORTANT: Deadlocking latch must stop on

strike when door is closed.

Strike

Strike Box

Attaching Screws

Strike Box

Attaching Screws

#8 -32 x 3/4"

#12 -24 x 3/4"

Figure 3

1. Use template A8290 to mark the door (See Figure 1).

2. Drill the door according to the template.

3. Verify the dimensions (See Figure 2).

4. Install the strike (See Figure 3)

part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

5Adjust Lock for Door Thickness (if necessary)

6Install Outside Assembly

To adjust lock to door thickness if other than 1-3/4”

(44mm) refer to Section 5.

Insert lockbody into door from outside making sure that

lockbody hooks latch case and retractor engages bolt

tail(s). See Figure 6.

DO NOT FORCE. (If lockbody does not engage latch easily,

check door preparation for errors.)

Latch bolt tail should be centered in depth of retractor. If

it is not, refer to Section 5 to properly adjust the lock for

door thicknesss.

Lock is factory preset for 1-3/4" (44mm) doors unless specified. To adjust

lock to door thickness if other than 1-3/4" (44mm):

1. Remove trim assembly from the lockbody. (See Figure 5).

2. Rotate mounting plate to adjust for proper door thickness.

• For 2" thick door the inside face of the mounting plate should be

flush with the face of the bearing. (See 5a).

• Verify correct position from the markings on the through-bolt

stud, or by measuring from inside surface of the mounting plate to

the centerline of the retractor (See 5b).

3. Reassemble the outside trim assembly to the lockbody.

4Latch Installation

Install screws (2) #8-32 x 3/4".

Figure 4

Spin the mounting plate to the left to

adjust for larger door thickness.

Figure 6

Trim Assembly

Figure 5

Figure 5a

Door Thickness Dimension A

1-3/4" (44 mm) 7/8" (22 mm)

2" (50 mm) 1" (25 mm)

2-1/4" (57 mm) 1-1/8" (29 mm) Figure 5b

Centerline

of retractor

Retractor

Dimension A

Bearing

These

surfaces

flush

Mounting Plate

without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

7Install Inside Components

1. Remove rose from inside spring housing assembly.

2. Align and insert inside spring housing onto the installed lockbody.

3. Install screws to tighten the lock to the door.

4. Orient dimples on the side of the rose horizontally at 3 and 9 o’clock position in line with the openings on the spring

housing assembly. See Figure 7.

5. Install rose onto the inside spring housing assembly.

6. In the unlocked position, verify the button is adjusted properly. See Figure 8 for proper alignment. Adjust if necessary.

7. Install inside lever.

8Cylinder Installation

Cylinder spacer should

be installed “snapped”

on to the cylinder be-

fore installing into the

outside trim assembly.

Correct Key Orientation

During Assembly

Outside Lever

Cylinder

Cylinder Spacer

IMPORTANT

Before installing cylinders:

• Use a flat blade screwdriver to rotate cam until the driver points are in a 6 and 12 o’clock position. See Figure 15 on page 5.

a Standard Cylinder (Figure 9)

Screws (2) #10-32 x 1-1/4"

Figure 7

Button in-line with shank indicates

correct position based upon door

thickness. If the button needs to be

adjusted, position it by depressing

the plunger, moving it in or out as

needed.

Figure 8

Figure 9

Key

Rose dimple

Rose dimple opening

Note: Test for proper operation before closing door.

part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

8Cylinder Installation, continued

New Core

• Remove temporary construction core or plastic core. If keyed, use Control Key

(stamped “C”) rotate 15° and pull.

• Insert permanent core into lever with control key; rotate 15° and remove key.

SFIC

b Interchangeable or Removable Core (Figure 10)

IMPORTANT

• Remove tailpiece from construction core and insert into new core. If using 7 pin cores,

insert the 7 pin tail piece that’s supplied with the lock, before installing the core into the

lock.

• For XC LFIC cores, snap-on retainer must be installed onto tailpiece. Tail and retainer

assembly will press fit onto back of core.

Remove

Construction Core

Install New/

Final Cylinder

Remove/Reuse 6 Pin Tailpiece

Plastic Core

7 Pin

In Core

Keyed

Core

Construction Core

Keyed

Core

6 Pin

In Core

To Remove:

Rotate key 45° and hold. Depress lever catch with pin tool.

Lever catch

To Remove:

Remove core and tailpiece, using control key (stamped “C”).

Insert slotted screwdriver or lever release tool into the cylinder

opening and make contact with the lever catch.

To Remove:

Depress lever catch with pin tool, remove lever.

To Install:

Slide lever on over the lever catch. Confirm the lever will not

pull off.

a Standard Cylinder (Figure 11)

b Interchangable or Removable Core (Figure 12)

c Plain Lever (Figure 13) & Push/Turn Button (Figure 14)

Control Key*

To Install:

With driver points at 6 and 12 (See Figure 15), rotate key 45° in either

direction, and then slide the lever on over the lever catch. Confirm the

lever will not pull off.

Pull lever catch horizontally towards the opposite side of the cylinder

opening and remove lever. *Note

For 1-Bitted cylinders, utilize a control key cut 113511.

9Lever Removal & Installation

Figure 11

Figure 12

Figure 13 Figure 14

Figure 10

XC LFIC

To Install:

Without the core installed, slide the lever over the lever catch. Confirm the lever will not pull off. Install core and tailpiece,

using control key (Stamped “C”).

without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

11 Other Instructions

a Remove Outside Lever for Exit Latch 10XG13

1. Remove inside lever (See Section 9).

2. Remove rose.

3. Remove (2) mounting screws and inside housing assembly. See Figure 16.

4. Remove outside trim assembly.

5. Push and hold plug back (located inside of outside trim assembly). See Figure 17.

6. Push lever catch with push pin and remove lever.

Remove

Push Push and Hold Plug

(2) Mounting Screw

Inside Housing Assembly

Lever

Rose

Outside Trim Assembly

Figure 16

Figure 17

10 Timing 10XG26 & 10XG38

1. Remove outside and inside levers (See Section 9).

2. Adjust cams visible from both the outside and inside lock trim.

2a. Use a flat blade screwdriver to rotate each cam until the driver

points are in a 6 and 12 o’clock position. (See Figure 15)

3. Re-install outside and inside levers.

4. Test both cylinders with key before closing the door.

Figure 15

View into lock from

end of trim

12 o’clock drive point

6 o’clock drive point

part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

11 Other Function Instructions, continued

Outside Trim Assembly

Screws (2) #10 - 32 x 1-1/4"

Cup Washer

Inside Trim Assembly

Figure 18

Figure 19

Inside Trim Assembly

12 Miscellaneous Options

a 1-3/8" Doors (1- Option)

Outside Trim and

Lockbody

Adapter Plates

Inside Trim Assembly

Install (1) adapter plate between the door and rose assemblies (both sides).

• Inside trim to be aligned with holes marked screw slot.

• Outside trim through-bolts to be aligned with through-bolt holes marked on adapter plate.

b Install Single Lever Pull 10XU93

c Install Double Lever Pull (10XU94/ 10XU94-2)

Screws (2) #10 - 32 x 1-1/4"

Used with 10XU94-2 only

without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8286 04/21

10X Line

Installation Instructions

Cylindrical Lockset

12 Miscellaneous Options

Tailpiece

1. Provided less core.

2. Tailpiece included with lock.

3. Attach tailpiece to Schlage® LFIC and insert into the lever.

1. Provided less core.

2. Depress cap pin and unscrew end cap to

remove tailpiece from competitor cylinder.

3. Insert new tailpiece, in orientation shown.

4. Re-assemble end cap over new tailpiece.

b Lever to Accept Schlage®LFIC (SF- Option)

c Lever to Accept Schlage®or Yale®Fixed Core Cylinder (30- or YC- Option)

d Lever to Accept Yale®LFIC (YRC- Option)

Competitor’s

Cylinder

Cap Pin

End Cap

1. Provided less core.

2. Slide provided spacer over tailpiece

3. Insert driver assembly into back of core.

A8286 04/21

1-800-727-5477 • www.sargentlock.com

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

12 Miscellaneous Options

e 10XG50 Hotel Function Adjustment

1. Remove lever, cylinder and spacer from assembly.

2. Insert adjustment tool (provided with lock) into interior cap as shown below.

4. Rotate back counter-clockwise until tool handle is approximately in line with the end of the shank (as shown) AND cap slot

orientation is vertical. Slot alignment may require a slight rotation in either direction.

5. Remove adjustment tool and re-install cylinder and lever. Lever install will require key be rotated 90° counter-clockwise.

3. Rotate cap clockwise until fully tight.

- To adjust timing of hotel cylinder key lockout indicator

cap

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Lockwood Nexion Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 319 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Harmony H1 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff ANYKEY 496 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 8816 Bedienungsanleitung

Assa Abloy

Assa Abloy MSL sFlipLock drive Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch Technische Daten

Assa Abloy

Assa Abloy 179C Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Delayed Egress Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Essential YDME 70 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W73 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin EcoFlex NAC Series Montageanleitung

Assa Abloy

Assa Abloy SARGENT7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Mini Magnet Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Profile G1 Series Bedienungsanleitung

Assa Abloy

Assa Abloy v.G1 Sargent Bedienungsanleitung

Assa Abloy

Assa Abloy LE932 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lock SL Technische Daten

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W0700 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung