Assa Abloy SARGENT7800 Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com

A8257E 4/22

Installation Instructions

7800 & 8200 Series Mortise Lock

Used with Sectional Trim and V Series Indicators

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/

patents.

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in dam-

age to the product and void the

factory warranty.

WARNING

1-800-727-5477 • www.sargentlock.com A8257E 4/22

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with Sectional Trim and V Series Indicators

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

Tools Required

#2 & #3 Phillips

head screwdrivers

Flat blade

screwdriver

1/8"Allen

Wrench

3/32"Drill bit T-20 Torx Screw

with Tamper Pin

Driver

Indicator Variants

Depending on function and option ordered, indicators are provided in the following variations, these instructions detail how

to install with cylinder, however other variations follow similar instructions. (Figure1)

Contact factory for any questions.

Figure1

Coin Turn - For

installation

on outside of

door.

Cylinder - For

installation

on inside or

outside of

door.

No input /

blank - For

installation

on inside or

outside of

door.

Thumbturn -

For installation

on inside of

door.

Lock set configuration

To set function of multi-function lock or to re-hand, see instructions on lock body.

1-800-727-5477 • www.sargentlock.com

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with Sectional Trim and V Series Indicators

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

A8257E 4/22

Rehanding indicator

Indicator spindle cams MUST be oriented correctly per lock function and door mounting location. Verify hand and bevel of

door. (Figure2)

Left Hand

Hinges Left

Open Inward

Right Hand

Hinges Right

Open Inward

LHRB

Left Hand

Reverse Bevel

Hinges Left

Open Outward

RHRB

Right Hand

Reverse Bevel

Hinges Right

Open Outward

Figure2

Note:

Stand on outside of locked door when determining door hand.

Next, verify inside and/or outside indicators are handed correctly,

using Spindle Cam Position chart. (Figure3) If they are handed

correctly, skip to Step 5 "Prepare Door".

If they are not handed correctly:

1. Remove retaining pad and spindle cam from assembly. (Figure4)

2. Position spindle cam in correct direction for door hand. (Figure3)

Important:

• For thumbturn indicators, make sure thumbturn

is positioned in the 12 o’clock direction as

shown. (Figure5)

3. Slide spindle cam post into correct slot of display slide. (Figure4)

4. Re-seat retaining pad into original position.

5. Return indicator to the vacant/unlocked position for installation.

Scan this QR

code for the

Sargent Indicator

Handing Charts

Door Hand: RH / RHRB

Door Hand: LH / LHRB

Outside Indicator

Inside Indicator

Outside Indicator

Spindle Cam Position for Locks with Deadbolt

(*and 56 function)

Door Hand: RH / RHRB

Door Hand: LH / LHRB

Outside Indicator

Inside Indicator

Outside Indicator

Spindle Cam Position for Locks without

Deadbolt (*except 56 function)

Figure3

Figure4

Spindle

cam

Display

slide slot

Retaining

pad

Thumbturn

position

Figure5

1-800-727-5477 • www.sargentlock.com A8257E 4/22

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with Sectional Trim and V Series Indicators

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

aPrepare Door for Mortise Lock

bInstall Lock

Installation

RH door

shown

Inside of door

Outside

of door

Lock

Lock Screws

Figure6

Prepare door for function holes, size, and location according to A7050 door

marker template, if not already prepped.

1. Verify strike location according to template.

Clean out door pocket and door edge of debris.

2. Make sure handing of lock matches handing of door. Slide lock into door. (Figure6)

3. Temporarily hand tighten two (2) lock screws (#12 x 1-1/4"wood screws, or #12-24 x1/2"machine screws).

Notes:

• Keep door open until installation is complete.

• If installing lever onto only one (1) side of door (36 function), see separate instruction sheet A7028.

cPrepare Door for Indicator

Template

Guide

Mark holes

with pencil

Figure7

Control Hub

1. Insert template guide into control hub on side where indicator will be

used. (Figure7)

2. Slide indicator template over template guide.

Important: Make sure the template is properly centered and aligned

to ensure smooth indicator operation.

3. Mark the four (4) hole positions indicated on template.

4. Remove guide and template.

5. If indicators are being used on both sides of door, repeat steps 1

through 4 for opposite side.

6. Remove lock body.

7. Drill four (4) marked holes with 3/32" diameter bit, by 1/2" deep.

8. Reinstall lock body and hand tighten screws.

Note:

If retrofitting over an existing product, ensure door surface is free of chips

and debris around holes so indicator will sit flat against door surface.

1-800-727-5477 • www.sargentlock.com

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with Sectional Trim and V Series Indicators

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

A8257E 4/22

Installation, continued

dInstall Levers Inside of door

Inside Lever

Rose

Adapter

Plate

Spindle

#8-32 x

5/8" screws

Outside of door

RH door

shown

Figure8

Set screw

Outside

lever & Rose

Assembly

#6 x 3/8"

screws

Mounting

Plate

Figure9

Figure10

eInstall Indicator Mounting Plate

1. Slide outside lever and rose assembly through door and lock

body, and hold. (Figure8)

2. Slide inside spindle into lock body hub.

3. Slide adapter and plate assembly over spindle.

4. Secure with two (2) #8-32 x 5/8" screws.

5. Install inside rose onto adapter plate.

6. Install inside lever on adapter plate. Secure with set screw.

1. Screw indicator mounting plate to door with four (4) #6 x 3/8"

sheet metal screws. (Figure9)

2. If indicators are being used on both sides of door, repeat step 1

for opposite side.

fInstall Indicator Assembly

1. Verify lock is in unlocked state (turn outside lever to confirm).

2. Verify indicator is in vacant/unlocked position.

3. Assemble indicator assembly onto mounting plate. (Figure10)

4. Secure indicator assembly to door with two (2) machine

screws.

• Use #8-32 x 5/8"screw for top

• Use #8-32 x 3/8"screw for bottom

5. If indicators are being used on both sides of door, repeat steps 1

through 3 for opposite side.

Note:

Torx security screws recommended.

1-800-727-5477 • www.sargentlock.com A8257E 4/22

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with Sectional Trim and V Series Indicators

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

Installation, continued

gInstall Cylinders

Cylinder

Clamp

Screw

Figure11

Incorrect

Key and cylinder must be rotated as shown.

Correct

Figure12

Figure13

Lock screw

Outside front

#8-32 x 1/4"

screws Lock

screw

1. Thread cylinder into lock until flush with escutcheon surface. (Figure11)

• Pull key slightly out of cylinder to help thread into lock body.

2. Tighten cylinder clamp screw with #2 Phillips screwdriver.

• Check operation and adjust if necessary.

Notes:

• SARGENT logo must be horizontal and on top. (Figure12)

• If double cylinder function is used, repeat steps 1 and 2 for second

cylinder.

• Removable Core or Interchangeable Core cylinders

require a control key (key stamped with C) to remove and

install the core. This is not provided standard; it must be

requested separately. If requesting 1-bitted control key,

specify 113511 cut.

hInstall Outside Front

1. Tighten the two (2) lock screws completely: (Figure13)

2. Attach outside front with two (2) flat head screws #8-32 x 1/4".

iPerform Functional Check

DO NOT FORCE if resistance is encountered during functional

check. Refer back to Rehanding Indicator (if required) section to ensure

correct handing. Rehand if necessary.

1. Insert key into cylinder (if present) and rotate:

• Ensure there is no friction against lock case or any other

obstructions.

2. Check key retracts latch:

• Key should rotate freely.

3. Throw deadbolt (if present):

• Check key retracts both deadbolt and latch.

4. Test levers:

• Confirm latch and deadbolt (if installed) retract.

5. Verify indicator displays correct status when locked and unlocked.

1-800-727-5477 • www.sargentlock.com

7800 and 8200 Series Mortise Lock

Installation Instructions

Used with Sectional Trim and V Series Indicators

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

A8257E 4/22

Figure14

Indicator Parts List

Figure14 Description Part Number Req.

Sectional Escutcheon - Cylinder 81-0742 x finish

Sectional Escutcheon - Coin Turn 82-5635 x finish

Sectional Escutcheon - Thumbturn (Standard) 82-5630 x finish

Sectional Escutcheon - Thumbturn (LB Option) 82-5631 x finish

Sectional Escutcheon - Thumbturn (T1) 82-5632 x finish

Sectional Escutcheon - Thumbturn (T2) 82-5633 x finish

Sectional Escutcheon - Thumbturn (T3) 82-5634 x finish

Sectional Escutcheon - No Input/Blank 81-0742 x finish

2 Indicator Window 81-0811 1

Indicator Display Assembly - Green Unlocked / Red Locked 82-5602

Indicator Display Assembly - Green Vacant / Red Occupied 82-5603

Indicator Display Assembly - Green Unlocked Icon / Red Locked Icon 82-5604

Indicator Display Assembly - White Unlocked / Red Locked 82-5605

Indicator Display Assembly - White Vacant / Red Occupied 82-5606

Indicator Display Assembly - White Unlocked Icon / Red Locked Icon 82-5607

Indicator Display Assembly - Green Ouvert / Red Fermé 82-5684

Indicator Display Assembly - Green Libre / Red Occupée 82-5685

4A Indicator Spindle Cam - Thumbturn/Coin Turn 81-0745

14B Indicator Spindle Cam - Cylinder/No Input / Blank 81-0756*

4C Indicator Spindle Cam - 05, 37, 38, 59 Function 82-5577*

4D Indicator Spindle Cam - 05 (Inside) 82-5673 1

5 Indicator Retaining Pad 81-0749 1

6 Sectional Indicator Screw Pack 82-5590 x finish 1

7 Sectional Indicator Mounting Plate 81-0750 1

8 Sectional Indicator Template Kit (not shown) 82-5601 1

* These parts are for 1-3/4"standard thickness doors. For other thicknesses, please contact factory.

Note:

Reference 8200 Series parts manual for all lock body parts.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov. A8257E 4/22

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Sargent PE8893 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effef 118 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDM3109A Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio Bedienungsanleitung

Assa Abloy

Assa Abloy LOCKWOOD 3782 Bedienungsanleitung

Assa Abloy

Assa Abloy IP2326N Betriebsanleitung

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Selector Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FM7100 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 700 ML20700 TCPWI1... Bedienungsanleitung

Assa Abloy

Assa Abloy Valencia AJAX Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Signature Series Bedienungsanleitung

Assa Abloy

Assa Abloy 179E Benutzerhandbuch

Assa Abloy

Assa Abloy Corbin Russwin FE5400S Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 800 TCAC2 Series Installationshandbuch

Assa Abloy

Assa Abloy Corbin Russwin Access 600 TCRNE1 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron TSH Series Bedienungsanleitung

Assa Abloy

Assa Abloy 179B S4 Benutzerhandbuch

Assa Abloy

Assa Abloy Conrbin Russwin IN120 WiFi Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 809M Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung