Assa Abloy V.G1 Sargent Bedienungsanleitung

Installation Instructions For

Profile Series v.G1 Exit Device

A7757C

Sargent Manufacturing Company is prohibited.

FOR ASSISTANCE, CONTACT SARGENT AT800-727-5477 or www.sargentlock.com

800-810-WIRE (9473) • www.sargentlock.com •A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Table of Contents

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced TV technician for help

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.

Warning

1Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

Warning

General Description...........................................................................1

Specifications....................................................................................1

Features .............................................................................................1

Parts Breakdown .............................................................................2-5

Installation Instructions–Rim Type Device.....................................6-9

Installation Instructions–Mortise Type Device ............................10-13

Operational Check............................................................................14

Installation of the RF Technology Lock (G1-TU, G1-TA, G1-TP)......14

Page

Warning

!To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

800-810-WIRE (9473) • www.sargentlock.com • A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

The SARGENT Profile Series v. G1 Rim/Mortise Exit Device is designed for areas

which require stand alone authorized entry. It is a self-contained microprocessor-

controlled keypad with non-volatile memory. The keypad will hold a total of 100

(LK)/2000 (GI-LU, GI-PK, GI-PA, G1-TU, G1-TP, G1-TA) different user codes. User

locations “01” & “02” are utilized for Master and Supervisory Codes, respectively.

This product is operated by six (6) “AA” alkaline batteries. SARGENT exit devices

locks are designed with high quality components to provide high security,

performance and durability.

General Description

Items Supplied with Exit Device

Items included in your 8877 and 8977 Series Exit Device

carton:

• Outside Escutcheon with Keypad

• Outside motorized Trim Assembly

• Exit Device

• Mortise cylinder for 8977

• Rim cylinder for 8877

• Inside Escutcheon with Circuit Board and Battery Pack

• 6 “AA” alkaline batteries

• Screw Pack

Items included in your 8878 and 8978 Series Exit Device

carton:

• Outside Escutcheon with Keypad

• Outside Motorized Trim Assembly

• Exit Device

• Inside Escutcheon with Circuit Board and Battery Pack

• 6 “AA” alkaline batteries

• Screw Pack

Specifications

Profile Series Rim Exit

• Latch – 3/4" throw, stainless steel

• Outside motor driven “ET” lever controlled by keypad

• Push bar retracts latch from inside

• Fire stop provided on all lever handle designs

• Profile Series exit devices furnished for 1-3/4" doors

• UL Listed

• Accepts all SARGENT rim cylinders (8877 only)

• Key retracts latch (8877 only)

• Available in “ET” lever handle designs only

Profile Series Mortise Exit

• Latch – 3/4" throw, anti-friction, brass

• Outside motor driven “ET” lever controlled by keypad

• Push bar retracts latch from inside

• Fire stop provided on all lever handle designs

• Profile Series exit devices furnished for 1-3/4" doors

• UL Listed

• Accepts all SARGENT mortise cylinders (8977 only)

• Key retracts latch (8977 only)

• Available in “ET” lever handle designs only

Features

• Low battery alert – 4 chirps after code entry

• External remote “request to enter” connector

• Master, Emergency or Supervisory code will unlock door

when low battery has expired

• Programming done at keypad or with a PDA using

SofLink™ Plus software and a PC (software required for

G1-PA & G1-TA)

• Entry of three wrong User Codes disables all codes for

ten seconds. Yellow LED on solid

• Last 15 transactions can be output to portable printer

via infrared link (LK Only)

• Last 2000 (Except LK) transactions can be output to

PC using a PDA and SofLink™ Plus software

800-810-WIRE (9473) • www.sargentlock.com •A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Parts Breakdown

8877/8878 x ET x Lever Design

Profile Series Rim Exit Device

11 14

13 (X2)

18 (X4)

800-810-WIRE (9473) • www.sargentlock.com • A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

ITEM PART No. DESCRIPTION REQ’D

1 52-2839 Outside Escutcheon (Prox Only) Assembly (G1-PA, G1-TA) 1

52-2474 Outside Escutcheon (Keypad Only) Assembly (LK)

1 52-2838 Outside Escutcheon (Keypad/Prox) Assembly (G1-LU, G1-PK, G1-TU, G1-TP) 1

52-2704 Key Pad and Proximity Assembly (G1-LU, G1-PK, G1-TU, G1-TP) 1

52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 1

52-2706 Proximity Only Assembly (G1-PA, G1-TA) 1

68-1397 Outside Escutcheon Housing Only 1

52-0176 Outside Escutcheon End Cap 1

2 52-2460 Inside Escutcheon Assembly with 100 User Controller (LK) 1

2 52-2833 Inside Escutcheon Assembly with 2000 User Controller (G1-LU) 1

2 52-2834 Inside Escutcheon Assembly with Prox/Key Pad Controller (G1-PA, G1-PK) 1

52-2836 Inside Escutcheon Assembly (Keypad Only)

with RF Technology Controller (G1-TU)

52-2835 Inside Escutcheon Assembly (Keypad/Prox or Prox Only)

with RF Technology Controller (G1-TA, G1-TP)

68-1396 Inside Escutcheon Housing Only 1

52-0175 Inside Escutcheon End Cap Only 1

52-2441 100 User Controller Assembly (LK) 1

52-2783 2000 User Controller Assembly (G1-LU) 1

52-2784 2000 User Controller Assembly (G1-PA, G1-PK) 1

52-2786 2000 User (Keypad/Prox or Prox Only) Controller Assembly w/ RF Technology (G1-TA, G1-TP)

52-2785 2000 User (Keypad Only) Controller Assembly w/ RF Technology (G1-TU)

3 52-0170 Battery Cover 1

52-2309 Battery Cover – RF Technology (G1-TU,G1-TP, G1-TA)

4 01-1212 Security Screw 1

5 01-0297 Security Tool 1

6 52-0033 Fire Stop Plate 1

7 01-1500 Fire Stop Screws #8 x 1/2” Type “AB” Phillips Pan Head Self Tap 2

01-0803 Battery Alkaline (“AA” Cell) 6

9 52-0253 Battery Keeper 1

52-0344 Battery Keeper – RF Technology (G1-TU, G1-TP, G1-TA)

10 52-2425 Screw Pack (Includes item numbers 5, 6, 7, 15) 1

11 Consult Factory Motorized ET Lever Trim 1

12 Consult Factory Motor and Harness Assembly 1

13 01-4451 ET Through-bolts 2

14 13-0074 Cylinder Retaining Screws 2

15 77-0685 Escutcheon Through-bolts 2

16 68-4261 Center Case Assembly LHRB & RHRB (Std.) 1

68-4263 Center Case Assembly LHRB (12-) & RHRB (12-) 1

17 68-0406 Chassis Cover 1

18 97-0052 Chassis Cover Screws 4

800-810-WIRE (9473) • www.sargentlock.com •A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Parts Breakdown

8977/8978 x ET x Lever Design

Profile Series Mortise Exit Device

Door

19 (X4)

800-810-WIRE (9473) • www.sargentlock.com • A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

ITEM PART No. DESCRIPTION REQ’D

1 52-2839 Outside Escutcheon (Prox Only) Assembly (G1-PA, G1-TA) 1

1 52-2838 Outside Escutcheon (Keypad/Prox) Assembly (LK, G1-LU, G1-PK, G1-TU, G1-TP) 1

52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 1

52-2704 Key Pad and Proximity Assembly (LK, G1-LU, G1-PK) 1

52-2706 Proximity Assembly (G1-PA, G1-TA) 1

68-1397 Outside Escutcheon Housing Only 1

52-0176 Outside Escutcheon End Cap Only 1

2 52-2460 Inside Escutcheon Assembly with 100 User Controller (LK) 1

2 52-2833 Inside Escutcheon Assembly with 2000 User Controller (G1-LU) 1

2 52-2834 Inside Escutcheon Assembly with Prox/Key Pad Controller (G1-PA, G1-PK) 1

52-2836 Inside Escutcheon Assembly (Keypad Only)

with RF Technology Controller (G1-TU)

52-2835 Inside Escutcheon Assembly (Keypad/Prox or Prox Only)

with RF Technology Controller (G1-TA, G1-TP)

68-1396 Inside Escutcheon Housing Only 1

52-0175 Inside Escutcheon End Cap Only 1

52-2441 Enclosure (LK) Assembly 1

52-2783 Enclosure (G1-LU) Assembly 1

52-2784 Key Pad/Proximity Only Controller (G1-PA, G1-PK) Assembly 1

52-2786 2000 User (Keypad/Prox or Prox Only) Controller Assembly (G1-TA, G1-TP)

52-2785 2000 User (Keypad Only) Controller Assembly (G1-TU)

01-0803 Battery Alkaline (“AA” Cell) 6

3 52-0170 Battery Cover 1

52-2509 Battery Cover – RF Technology (G1-TU,G1-TP, G1-TA)

4 01-1212 Security Screw 1

5 01-0297 Security Tool 1

6 52-0033 Fire Stop Plate 1

7 01-1500 Fire Stop Screws #8 x 1/2” Type “AB” Phillips Pan Head Self Tap 2

9 52-0253 Battery Keeper 1

52-0344 Battery Keeper – RF Technology (G1-TU, G1-TP, G1-TA)

10 52-2425 Screw Pack (Includes item numbers 5, 6, 7, 15) 1

11 Consult Factory Motorized ET Lever Trim 1

12 Consult Factory Motor and Harness Assembly 1

13 01-4451 ET Through-bolts 2

15 77-0685 Escutcheon Through-bolts 2

16 68-2172 Center Case Assembly LHRB (Standard and 12-) 1

16 68-2173 Center Case Assembly RHRB (Standard and 12-) 1

17 99-2401 Mortise Lock LHRB 1

17 99-2402 Mortise Lock RHRB 1

18 68-0407 Chassis Cover 1

19 97-0052 Chassis Cover Screws 4

800-810-WIRE (9473) • www.sargentlock.com •A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Installation Instructions for Rim Type

Exit Device 8877/8878

Inside

Outside

Left Hand

Reverse Bevel

"LHRB"

Right Hand

Reverse Bevel

"RHRB"

IMPORTANT: BEFORE STARTING

•This device is non handed

•Door should be fitted and hung

•Verify box label for size of exit device, function and hand

Step #1 – Exit Hardware & Door Prep

1. If using a mullion, install in frame.

2. Prep door according to Exit installation instructions A6770 and template 4640 (metal and wood doors).

Step #2 – Installation of Outside Trim, Exit Chassis and Cylinder

A. Outside Trim

1. For exterior applications “ET” gasket (52-0263)

should be used to seal between “ET” escutcheon

and outside door surface

2. Route harness through under cut of cylinder hole

and out to other side of door

3. Place “ET” control onto door

B.Inside Trim

1. Route “ET” harness along track cutout for wood

doors and access hole for metal doors

2. Mount exit chassis carefully. DO NOT PINCH

HARNESS WIRES

3. “ET” spindle will engage into the hub of exit device

chassis

4. Secure chassis and “ET” with (2) 1/4 -20 x 2-3/8"

flat head machine screws

C. Cylinder Installation

NOTE: For devices without cylinder, go to Step D2.

1. Insert cylinder into “ET” control

2. Mate cylinder tailpiece into hub of exit device

chassis

3. Make sure “ET” harness is clear of cylinder and

cylinder tailpiece

D. Securing Cylinder

1. Secure cylinder to exit chassis using (2) #12-24 x

1-7/8" connecting screws

2. Fasten exit chassis to door using (4) #10 wood

screws or #10-24 machine screws

#34

Cylinder

ET Control

Wire

harness

Wire harness

(2) 1/4-20 x 2-3/8"

Flat head

machine screws

secures ET Exit Chassis

(2) #12-24 x 1-7/8"

Flat head connecting

screws for cylinders

(4) #10 Wood

screws or #10-24

machine screws

Outside

of door ET gasket

Inside

of door

Outside

of door

Inside

of door

800-810-WIRE (9473) • www.sargentlock.com • A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Step #3 – Attach Fire Stop Plate

Installation Instructions (Continued)

Outside

of door

1-1/2'' Dia.

7/8''

NOTE: Required for 12- Fire Rated doors only

1. Drill (2) 1/8" diameter holes if the door is not supplied with them

2. Secure fire stop plate to door with (2) #8 x 1/2" self tapping screws

Outside

of door

Wires & connector

go through fire

stop plate

Keypad ribbon

cable/connector

12 3

456

789

Step #4 – Installation of Outside Escutcheon

Insert connector and wires

1. For exterior applications gasket (68-1400) should be

used to seal between escutcheon and outside door surface

2a. For 12- fire rated devices feed keypad ribbon cable/connector

from outside of door through gasket then fire stop plate

2b. For non-12- exit devices, feed keypad ribbon cable/connector

through gasket then conduit hole in door

3. Place escutcheon against door surface

For exterior applications.

gasket (68-1400) should

be placed between the

escutcheon and door surface

Non Fire Rated Exterior Doors-

Install Weather Conduit

(P/N 52-2847) as shown below

800-810-WIRE (9473) • www.sargentlock.com •A7757C

Profile Series v.G1 Exit Device

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Rim Installation Instructions (Continued)

1. Connect ground wire to terminal E3 (Fig. 1), keypad harness to controller (Fig. 2), and ET motor harness to motor

connector (Fig. 3).

2. Place extra wire inside door hole and/or outside escutcheon being careful not to pinch wires.

3. Connectors go on only one way, do not offset connector and be sure they are completely seated.

4. Insert #8-32 x 1-1/4" screws through inside escutcheon and thread into outside escutcheon. Straighten

escutcheons and tighten securely.

Ground

wire

ET Motor

harness

Keypad

harness

Outside

of door

Inside

of door

Step #5 Installation of Inside Escutcheon

Fig. 1

Fig. 3

Fig. 2

Note : For RF Technology versions (G1-TU, G1-TP, G1-TA) refer to Section 9 to install through bolt screws.

Note: For RF Technology

version refer to Section 9.

Andere Handbücher für v.G1 Sargent

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Conrbin Russwin IN120 WiFi Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD226 Technische Daten

Assa Abloy

Assa Abloy Yale eBoss 886F Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch NTB610 Technische Daten

Assa Abloy

Assa Abloy HES 9400 Betriebsanleitung

Assa Abloy

Assa Abloy Yale real Living Assure Lock SL Technische Daten

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem type A Leitfaden

Assa Abloy

Assa Abloy Rixson 73ER Bedienungsanleitung

Assa Abloy

Assa Abloy Valencia Hola Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 10X Series Bedienungsanleitung

Assa Abloy

Assa Abloy 179C Bedienungsanleitung

Assa Abloy

Assa Abloy LE932 Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio C100 V3 Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron DSB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale AYRD110 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent AL-PE80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy CL33700 TCPWI1 Bedienungsanleitung

Assa Abloy

Assa Abloy 1264 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy KESO KEK i-handle S Bedienerhandbuch

Assa Abloy

Assa Abloy Corbin Russwin ED2400 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung

Assa Abloy v.G1 Sargent Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken