Assa Abloy SARGENT BL7300 Series Bedienungsanleitung

A8220D 10/19

Installation Instructions

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

Important

The latches, rods, and cassette are pre-installed.

This product must be installed by a factory trained technician.

Multi-Point Lock

FM7300 Series and BL7300 Series

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

TOC Table of Contents

1 Package Contents ...............................................................4

2 Tools Required ..................................................................5

a Tools Required for Electronic Access Control (EAC) Shield ........................5

b Tools Required for Dogging Indicator Option.....................................5

3 Installation ......................................................................6

a Check Door......................................................................6

b Door Installation ................................................................6

c Install Top Strike into Door Frame................................................6

d Install Center Strike into Door Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

e Remove Retractor Inserts........................................................7

f Check Latches (uninstalled)......................................................7

g Install Bottom Strike.............................................................8

h Top and Bottom Latch Adjustment............................................. 10

i Mortise Lock Install ............................................................ 12

j Final Mortise Lock and Trim Installation ........................................ 13

k Electronic Access Control (EAC) Reader and Controller Installation ............. 13

l Deadbolt Label Installation (FM7300 Only) .................................... 13

m Key Override with Deadbolt Function Operation Check ........................ 13

n Electronic Access Control (EAC) Shield (if applicable)........................... 14

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

4 Optional Installation........................................................... 14

a Dogging Indicator Installation ................................................. 14

5 Addendum .................................................................... 17

a Check Door.................................................................... 17

b Place Door Horizontal on Sawhorse............................................ 17

c Install Lockbody Cassette (LBC) ................................................ 18

d Latch Rod Guides .............................................................. 18

e Feed Top Rod into Door........................................................ 19

f Align with Lockbody Cassette (LBC) ............................................ 19

g Troubleshoot Latch Installation ................................................ 20

h Correct Rod Installation Check................................................. 20

i Secure Top Latch .............................................................. 21

j Tighten Set Screw ............................................................. 21

k Bottom Latch Installation...................................................... 22

l Check Latch ................................................................... 22

m Mortise Reinforcer and Mortise Lock Installation ............................... 23

n Final Installation............................................................... 23

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

1 Package Contents

Part Number Description

1 82-5342 Multipoint cassette

2 82-5345 Trim mounting screw pack

3 82-5346 Top/bottom case mounting screw pack

4 82-5347 Top strike pack

5 82-5348 Bottom strike pack

6 82-5349 Mortise mounting/reinforcement pack

7 82-5350 Center strike pack

82-5351 IN/PN Inside cover shield pack

82-5352 Harmony inside cover shield pack

82-5353 Passport inside cover shield pack

9 188 Dogging indicator (includes item 13) (specify finish)

10 82-5383 Screw retainer pack

11 82-5386 Top case and rod assembly (specify door size)

12 82-5387 Bottom case and rod assembly (specify door size)

13 82-5400 Dogging indicator screw pack (specify finish)

14 01-4597 T-wrench, adjustment

15 Consult factory Outside armor front

16 Consult factory Mortise lock

17 Consult factory Mortise trim

18 Consult factory Cylinder

Note:

The grayed parts are preinstalled by the

door manufacturer and relate to the

Addendum section beginning on page 16.

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2 Tools Required

Tape measure Hammer Flashlight 1/8" Allen

(supplied)

3/32" Allen

(supplied)

5/32" Allen

Drill 1/8" Masonry

drill bit

#3 Phillips

bit

Slotted

screwdriver

#1, #2, #3

Phillips head

screwdrivers

Chisel 3/8"

Anchor set

a Tools Required for Electronic Access Control (EAC) Shield

#29 Drill bit

(.136")

#8-32 Tap

b Tools Required for Dogging Indicator Option

#7 Drill bit

(.201")

82° Countersink

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation

a Check Door

Verify the door is:

• Correct size and hand for opening.

• Correctly prepared to Template 4740.

IMPORTANT

If measurement is incorrect, DO NOT PROCEED

WITH INSTALLATION. Contact door manufacturer.

(Figure1)

b Door Installation

Hang the door on the frame.

IMPORTANT

If the door rubs along the floor, do not complete

this installation! Contact door manufacturer.

c Install Top Strike into Door Frame

• Remove plastic strike filler and discard.

Figure1

Door Height

Door Width

of Lockbody

Outswing Door

Shown

± 5/64"

39-9/16"

(101.4 cm)

Figure2

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

d Install Center Strike into Door Frame

• Install two (2) ¼-20 socket cap flat head screws.

(Figure3)

e Remove Retractor Inserts

WARNING

The door now has the ability to latch.

(Figure4)

f Check Latches (uninstalled)

• Insert the uninstalled outside mortise trim and

rotate to verify the top and bottom latches

retract flush with the door. Do not install

mortise trim at this time. (Figure5)

• Move the top strike back and forth until the top latch engages the strike. (Figure6)

Figure3

Figure4

Figure5

TOP OF DOOR FRAME

Figure6

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

g Install Bottom Strike

• Close the door and mark the location of the bottom bolt.

3/8" MAX

Bottom of door

to floor.

✓

Figure7

• Open the door and place the strike over the bottom bolt location. Mark the location of the bottom

strike pocket and hole locations. (Figure7)

Note:

The strike is not symetric. Install as shown. If needed, the strike can later be rotated to increase bolt

clearance. (Figure8)

Door Swing

Jamb

Narrow

Wide

Bottom Strike Pocket

Figure8

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

g Install Bottom Strike (cont.)

Flush Mount (Figure9)

Mortise the strike into the floor 1/4" deep.

(Optional for 3/8" door to floor gap.)

IMPORTANT

Use a vacuum or compressed air to

clear holes ofdebris. (Figure10)

Cross Sectional View

Flush Mount (Figure11)

Surface Mount (Figure12)

Drill two (2) 3/8"

diameter holes

by 2-1/4" deep.

Chisel the bottom strike pocket

1" deep to ensure the bolt has

full projection.

Figure12

IMPORTANT

Use a vacuum or compressed air to

clear holes ofdebris. (Figure13)

Cross Sectional View

Surface Mount (Figure14)

2 1/4"

Figure14

Drill two (2) 3/8"

diameter holes

by 2-1/4" deep.

Chisel the bottom strike

pocket 1" deep to ensure

bolt has full projection.

1/4" D EEP

Figure9

Use the anchor tool

to set anchors.

Figure10

2 1/4

Figure11

Use the anchor tool

to set anchors

Figure13

Multi-Point Lock

Installation Instructions

FM7300 Series and BL7300 Series

A8220D 10/19

or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Installation (cont.)

h Top and Bottom Latch Adjustment

• With the door hung, measure the clearance

between the top and bottom bolts and strikes.

(Figure15)

Note:

If both measurements equal 1/16" proceed to Step

3i, otherwise proceed with Step 3h as follows:

• Remove the mortise filler cap and discard.

(Figure16)

• Retract the latches by roting the lever and

opening the door. (Figure17)

Figure17

• Using the supplied 1/8" Allen wrench, loosen

the set screw 1/4 turn maximum. This allows

hex rods to rotate during the latch bolt

adjustment. (Figure18)

Figure15

1/16" Bolt to strike clearance.

TOP OF DOOR

1/16" Bolt to strike clearance.

BOTTOM OF DOOR

Figure16

Note location

of set screws.

Figure18

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy 8788 Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL574 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Essential Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YD-01-CON-NOMOD Bedienungsanleitung

Assa Abloy

Assa Abloy effeff MAGAC-L Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent AD-PE8600 Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem type A Leitfaden

Assa Abloy

Assa Abloy RIXSON W0700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy MSL sFlipLock standard Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy SARGENT 5300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy EMTEK LISCIO Fehlerbehebungshandbuch

Assa Abloy

Assa Abloy Abloy EL648 Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron Magnalock M670BD Series Bedienungsanleitung

Assa Abloy

Assa Abloy EL580 Bedienungsanleitung

Assa Abloy

Assa Abloy effef 118 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDM3109A Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy KESO Bedienungsanleitung

Assa Abloy

Assa Abloy Access 3 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD216-ZW3 Montageanleitung

Assa Abloy

Assa Abloy Valencia Filip Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung