Assa Abloy CloserPlus Ramp Norton XF460 Bedienungsanleitung

Copyright © 2013, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9377-2208-020 (04-14)1

ASSA ABLOY

Installation Instructions Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR

Hinge Edgeof Door

Series Function SizingAdditional Closer Options:- “DA” indicates Delayed Action closing- “R” indicates Ramp Hold-Open function, not handed Optional Accessories:- 7788 Drop Plate- 2019L, 6890, 6891 Soffit Plate Accessories NOTE: For special applications a separate door and frame preparation template is packed with these instructions. In those cases, use this instruction sheet for installation sequence and closer adjustments only.Standard Frame InstallationCloser mounts on opposite to hinge (push) side of door. See Pages 3 and 4Narrow Frame InstallationCloser mounts on opposite to hinge (push) side of door.6890 and 6891 accessories required for this application (supplied separately).See Pages 3 and 4Flush Partition InstallationCloser mounts on opposite to hinge (push) side of door. 2019L accessory required for this application (supplied separately).See Pages 3 and 5CLP7500RCLP770XRHOHO1-62 THRU 6An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment.

CAUTION

“X” Designates closer size 2, 3, 4, 5, or 6

Hinge Edgeof Door

ASSA ABLOY

CloserPlus Ramp™ Door Closers (CLP-R)Model Numbers Included:

ASSA ABLOY

ComponentsScrew PackCloserArmCover OptionsOptionalAccessoriesFor Blade Stop6891 SpacerFor Frameor Blade Stop6890 BracketFor Flush Partition2019L BracketPlastic Cover (Standard)Metal Cover (Optional)2 Cover Screws2019S Block(provided) 2 Cover Screws 9/32" (7 mm) thru;3/8" (9.5 mm) dia. x3/8" (9.5 mm) deep ondoor opposite to closerStandardOptionalThrough-bolts andgrommet-nutsAllPreparation for FastenersDoor or FrameFastenersDrill-SizesSelf-Drilling ScrewWood3/16" (4.80 mm) Pilot hole required1/4" - 20 machine screwMetal Drill: #7 (0.201" dia.)(5mm)Tap: 1/4" - 20 Sleeve nuts and boltsHollowMetal9/32" (7 mm) thru;3/8” (9.5 mm) door faceopposite to closerAluminumor Wood3/8" (9.5 mm) throughAluminumor MetalNo drill requiredNote: Wood doors MUST be pre-drilled when using Self-Drilling Screws.SoffitPlateMain ArmScrewMain ArmSecondary ArmPowerAdjustment Nut

Standard Closer (4 Valves)

DA Option Closer (5 Valves)

TubeCap

ASSA ABLOY

Installation Instructions

Installation Dimensions Chart

Dim

Up to90°

90°-95°

95°-100°

100°-105°

105°-110°

110°-115°

CLP7500/CLP770X

A in./(mm)

10-1/8(257)

9-1/4(235)

8-5/8(219)

7-7/8(200)

7-3/8(187)

6-3/4(171)

B in./(mm)

10-5/8(270)

9-3/4(248)

9-1/8(232)

8-3/8(213)

7-7/8(200)

7-1/4(184)

C in./(mm)

10-3/4(273)

9-7/8(251)

9-1/4(235)

8-1/2(216)

8(203)

7-3/8(187)

Power Adjustment Chart

DOOR

Dim

MAXIMUM DOOR SIZE

32”(0.81m)

36”(0.9 m)

42”(1.1 m)

48”(1.2 m)

INT

CLP7500

EXT

INT

CLP7700

EXT

*17 - 360°, MAXIMUM AVAILABLE

Arm Mounting DetailPinion flat will face the door on either right or left hand doors.Arm to Pinion AssemblyFinal InstallationInstall arm roughly here with flat side of pinion to the correct marking on the arm per the illustration below

Select angle of opening and use dimensions shown on Page 4 and Dimension Chart below to locate 4 holes on door for closer body (or 4 holes for 7788 Drop Plate, Page 6, only if required) and 5 holes on stop/rabbet for Soffit Plate (or 4 holes on frame transom for 2019L bracket, only if required). For applications not covered in these instructions, a separate template will be required. Prepare door and frame for fasteners using “Preparation for Fasteners” chart on Page 2. Install closer body to door, or 7788 Drop Plate, with power adjustment shaft away from hinge edge of door and adjustment valves: Down for Left Hand Up for Right Hand Mount 7788 Drop Plate to door ... only if used (see Page 6). Install Main Arm: Close valves (‘S/D’ or ‘S’) and ‘L’, then using a wrench, rotate the pinion shaft at least 50° to permit alignment of the Pinion Flat with the proper arm mark: ‘Z’ for Left Hand ‘Y’ for Right Hand See below right for illustrations of this procedure. Reopen valves (‘S/D’ or ‘S’) and ‘L’, that were closed in previous step. With door closed, align soffit plate with holes in frame and fasten to frame with screws. Use 2019S and/or 6891 spacer blocks or 6890 reinforcing bracket as required. 7500 Series Closers only: Closer is shipped from factory set at mid-range. Using “Power Adjustment” chart below, rotate power adjustment shaft with 1/8” allen wrench supplied: Turn CLOCKWISE to increase power. Turn COUNTER-CLOCKWISE to decrease power. See Page 7 for the illustration of this step. Make adjustments to closer before installing cover. See Page 7 for closer adjustment instructions. CAUTION: Do Not back valves out of closer body or a fluid leak will result. Install cover.

FULL 360 DEGREE TURNSOF POWER ADJUSTMENTSHAFT

ASSA ABLOY

Standard FrameNarrow FrameNotes:Do Not Scale Drawing.Left Hand Door Shown.Same dimensions apply for Right HandDoor measured from centerline of pivot point.Dimensions are in inches (mm).See Page 3 for A , B, & C dimension values.ACLHinge or Pivot2-1/2(64)2-3/8(60)6-3/4(172)2-3/4(70)3/8(10)2(51)7/16(11)B1/2(13)2-1/16(52)1-3/8(35)2-3/4(70)Standard MountSoffit PlateBlade Stop Mount2019S Block6891 BlockSoffit Plate5/8 Ref.(16)3/8(10)2(51)7/16(11)Hinge orPivotCL1-1/2(38)1(25)B1-1/4(31.8)3/4(19)A2-1/2(64)2-3/8(60)6-3/4(172)NOTE: For Blade Stop Mounting only.Prepare 2 holes for 6890 bracket afterinstalling 6891 block. The 1” dimensionis from the bottom of the 6891 block.Soffit Plate6890 Bracket2 to 2-3/4(51 to 70)6890 Bracket6891 BlockSoffit Plate5/8 Ref.(16)Narrow Frame MountBlade Stop Mount2 to 2-3/4(51 to 70)

ASSA ABLOY

Flush Partition2-1/2(64)1/2(13)1-1/2(38)1-3/4(44)C3/4(19)ACLHinge or Pivot2-1/2(64)2-3/8(60)6-3/4(172)Soffit Plate2019L AngleBracket

ASSA ABLOY

Standard FrameFlush PartitionNarrow Frame7788 Drop Plate Mounting Holes7788 Drop Plate7788 Drop Plate7788 Drop Plate2019L Bracket6890 BracketNotes:Left Hand Door Shown.Same dimensions apply for Right HandDoor measured from centerline of pivot point.Dimensions are in inches (mm).See Chart below for D dimension values.CLHinge or Pivot4(102)4-3/4(121)5/16(8)1(25)4(102)4(102)4-3/4(121)5/16(8)1(25)4(102)Hinge orPivotCLCLHinge or Pivot4(102)4-3/4(121)5/16(8)1(25)4(102)DDD

Installation Dimensions Chart

Dim

Up to 90°

90-95°

95-100°

100-105°

105-110°

110-115°

CLP7500RCLP7500XR

Dinch/(mm)

9-7/8 (251)

9 (229)

8-3/8 (213)

7-5/8 (194)

7-1/8 (181)

6-1/2 (165)

ASSA ABLOY

Control Valve Adjustments(See Figure 3.)Closing Speed Controls (Figure 2A or 2B and 3.) Valve “S” Controls Sweep Range. Valve “L” Controls Latch Range.Unit AdjustmentOpening Cycle “Backcheck” valve controls the strength of cushioning in Backcheck Range. NEVER close this valve completely – it is not to provide a positive stop. (see Figure 4 and Figure 5).Closing Speed ControlsClosing Speed ControlsFigure 2Figure 32B2A

1/8"HexKey

SlowFast"L" (Latch)"L" (Latch)"S/D” (Sweep)"S" (Sweep)"S/D" (Delayed Action)StandardClosing CycleDelayed ActionClosing CycleStandard CloserDelayed ActionCloserAll ValvesDo not force valvescounter-clockwise outof closer body or a fluidleak will occur.Adjust Closing Speed Time to between 3 to 7 seconds from 90°. Use of the door by handicapped, elderly or small children may require greater closing time.Closed

10°

70°

Closed

10°

Closing Power ControlFigure 1Install closer per instructionswith the proper pre-load applied to the arm then adjust spring power. The power adjustment will notwork properly if the closerspring is not pre-loaded.To increase power, use 11/16"wrench to turn poweradjustment nut clockwise.To decrease power, turn nutcounter clockwise. DO NOT use a power drill or driver to turn adjustment nut. This will damage closer and void warranty.For 7500 Series OnlySet closer to desired size. For recommended sizes, refer to the Power Adjustment Chart on page 3.Opening Door ControlsFigure 4BackcheckFigure 5

1/8"HexKey

IncreaseDecrease

1/8"HexKey

Backcheck CushionBackcheck PositionOpen for backchecklater in door-openingcycle."P"(Normally Closed)"B"(NEVER CloseCompletely)Do not force valvescounter-clockwise outof closer body or a fluidleak will occur.Opening Cycle

The hold-open mechanism is controlled by the hex nut feature located on the secondary arm underneath cap. Remove the cap by pulling straight down. Use a 7/16” wrench to adjust. Turning hex nut feature clockwise will increase the hold-open force. Turning hex nut feature counterclockwise will reduce the hold-open force. Hold-open mechanism can not be disengaged.

Hold-Open Feature

CapHexDECREASE - - INCREASEDO NOT use a power drill or driverto turn adjustment nut. This will damage closer and void warranty.

3000 Highway 74 East • Monroe, NC 28112Tel: (877)- • Fax: (800)-338-0965974-2255www.nortondoorcontrols.com

ASSA ABLOY

Page Left Blank Intinially

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy MAB 609 + AC593 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6011 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 1105 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600H Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-C Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton Narrow Profile Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent FIREGUARD 2408 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5630 Series Kurzanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6011 Series Bedienungsanleitung

Assa Abloy

Assa Abloy King 640 Bedienungsanleitung

Assa Abloy

Assa Abloy MAB 609 + AC572 Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-CS Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy DC130 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Handbuch

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung