Assa Abloy Norton 6011 Series Bedienungsanleitung

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19

6011/6021 LAP Replacement

Installation Instructions

Pour la version francaise voir www.nortondoorcontrols.com.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

6011/6051 Unit (Pull Side)

Union Assembly

(6001U)

Union Spacer

(6001US)

Cover

(6001COV)

Arm Assembly

(7210-1A)

End Cap - RH

(6001ENRH)

Closer Assembly

(7500LAP)

Operator LAP

(6011LAP)

Conduit Assembly

(6001CON)

Backplate (6001BP)

Power Module Sub-assembly

(6001PM)

Power Supply

(6000SUP)

Motor (not eld

replaceable)

Track Assembly

(7200-1T)

Inverter

(6000IN)

End Cap - LH

(6001ENLH)

6021/6031/6061/6071 Unit (Push Side)

Union

Assembly

(6001U)

Union Spacer

(6001US)

Cover

(6001COV)

Adjusting Tube

and Shoe

(6620-12)

End Cap - RH

(6001ENRH)

Closer Assembly

(7500LAP)

Operator LAP

(6021LAP)

Conduit Assembly

(6001CON)

Backplate (6001BP)

Power Module Sub-assembly

(6001PM) Power Supply

(6000SUP)

Motor (not eld

replaceable)

Main Arm and Rod

(6020-1W)

Inverter

(6000IN)

End Cap - LH

(6001ENLH)

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19

6011/6021 Operator LAP Replacement

B. Remove Cover.

1. Grasping at locations shown, pull cover off of

unit. (Figure 2)

NOTE:

• Cover is not secured with screws.

• Take care not to pull union assembly

or end caps which are secured with

screws.

Figure 1

Grasp Here

Prepare Unit for Replacement Operator LAP

Figure 2

Selector

Mode

Switch

A. Turn off control of door.

1. Open union assembly access door and ip

selector mode switch to OFF position.

(Figure 1)

C. 6011/6051 PULL Unit:

Disconnect Arm from Pinion.

1. Open door.

2. Using a at blade screw driver, pull out clip

in track slider. (Figure 3)

3. Pull up slightly on arm so arm stud comes

out of slider. (Figure 3)

CAUTION: Arm will immediately start to

move toward door frame.

4. Remove screw and countersunk washer

using a Phillips screw driver. (Figure 4)

5. Using an adjustable wrench, rotate top

pinion 45 degrees toward door hinge and

hold. (Figure 5)

6. Slide arm off pinion and release adjustable

wrench.

Figure 3

Figure 4

Figure 5

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19 3

6011/6021 Operator LAP Replacement

1. Turn On/Off switch to OFF position on conduit

assembly. (Figure 8)

Union Assembly and Spacer not shown

D. Turn off power to unit.

Figure 6

C. 6021/6031/6061/6071 PUSH Unit:

Disconnect Arm from Pinion.

1. Open door.

2. Using 7/16" wrench, remove pinion screw

holding main arm on pinion. (Figure 6)

3. Using 7/16" wrench, loosen forearm screw

in main arm rod and adjusting tube so that

main arm can slide out of tube. (Figure 7)

CAUTION: Arm will immediately start to

rotate.

4. When pinion and main arm rotate so main

arm is perpendicular to door, slide main arm

off of pinion.

Figure 7

Figure 8

6021/6031 Arms Shown

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19

6011/6021 Operator LAP Replacement

D. Connect Operator LAP and Power Module Sub-assembly.

1. Attach 10-pin black connectors between

operator LAP and power module sub-assembly.

(Figure 9)

2. Attach 3-pin white connectors between operator

LAP and power module sub-assembly.

(Figure 9)

Replace Operator LAP

C. Install Replacement Operator LAP.

1. Orienting LAP so spring tube of closer is

pointed toward hinge edge of frame, slide LAP

over two (2) protruding screws and tighten.

(Figure 11)

2. Using six (6) 1/4-20 x 1/2" Phillips head screws,

secure LAP to backplate. (Figure 10)

6 LAP Mounting Screws

Figure 9

1. Remove six (6) screws securing LAP to

backplate. (Figure 10)

2. Loosen two (2) protruding screws and lift LAP

off of unit. (Figure 11)

B. Remove Operator LAP.

Protruding

LAP Mounting

Screws

Figure 10

A. Disconnect Operator LAP from Power Module Sub-assembly.

1. Detach 10-pin black connectors between

operator LAP and power module sub-assembly.

(Figure 9)

2. Detach 3-pin white connectors between

operator LAP and power module sub-assembly.

(Figure 9)

Figure 11

NOTE: Connectors are keyed and only attach one way.

NOTE: Holes in LAP align with threaded holes

in backplate.

NOTE: Screws to be torqued to 80 in-lb

minimum.

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19 5

6011/6021 Operator LAP Replacement

6021/6031/6061/6071 PUSH Unit

1. Place square of main arm onto closer

pinion. (Figure 16)

NOTE: Pinion at should be aligned as

shown. (Figure 17)

2. Attach main arm to pinion with pinion

screw and tighten with 7/16" wrench.

(Figure 16)

3. With door closed, rotate main arm

away from hinge until adjusting tube is

perpendicular (90 degrees) with door.

(Figure 18)

4. While holding arm in position, secure

rod to adjusting tube with forearm

screw. (Figure 19)

Figure 16

Figure 17

View from ceiling looking downward

6011/6051 PULL Unit

1. Open door.

2. Using an adjustable wrench, rotate top

pinion 45 degrees toward door hinge. You

will feel resistance from spring. (Figure 12)

3. While holding pinion at 45 degrees, slide

arm on bottom pinion parallel to frame as

shown. (Figure 12)

NOTE: Pinion at should be aligned as

shown. (Figure 13)

4. Secure arm to pinion with 1/4-20 x 1/2"

screw and countersunk patch washer.

(Figure 12)

5. Insert stud on arm into slider in track by

pressing clip on backside of slider onto stud.

(Figure 14)

6. To adjust track stop:

• Use allen wrench to loosen set screw in

bumper stop.

• Open door to full open position.

• Slide bumper stop until it just touches

end of slider.

• Tighten set screw in bumper stop so

bumper will stay in position.

(Figure 15)

Reconnect Arm

Set Screw

Bumper Stop

Slide

Assembly

Arm Stud

Figure 12

Figure 13

Figure 14 Figure 15

Figure 18

6021/6031 Arms Shown

Figure 19

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19

6011/6021 Operator LAP Replacement

B. Adjust spring force.

NOTE:

• The amount of effort to manually open or

close a door is called force and is controlled by

the operator’s closer spring.

• Make necessary mechanical adjustments

described in “A” above.

• A closer set to ADA required 5 lbs opening

force may not be strong enough to close door

due to latching hardware, air pressure, or

frame issues.

1. Using 11/16" wrench, turn nut in end of closer

body tube to desired force.

(Figure 21)

NOTE: If spring adjustment nut is too close

to end cap and wrench will not reach nut,

remove Torx screw in end cap access door and

slide door open. When nished, slide access

door closed and reinsert #6 Torx at head

screw to secure door. (Figure 21)

Adjustments

A. Adjust mechanical closer features.

NOTE:

• Make necessary mechanical adjustments so

unit functions as a standard surface mounted

door closer before adjusting spring force,

applying power, adding accessories or making

electrical/programming adjustments.

• Valve location S/D is not adjustable.

• Chain protection plate cutouts allow access to

valves. Use hex wrench to make adjustments.

(Figure 20)

Do not remove valves from closer.

Hydraulic oil will escape.

1. Closing Speed Controls (Figure 20)

• Valve “S” controls Sweep Range from

full open to 10°.

• Valve “L” controls Latch Range from

10° to closed.

2. Opening Cycle (Figure 20)

• Valve “B” controls strength of cushioning in

Backcheck Range.

NOTE: NEVER close Backcheck valve

completely – it is not to provide a positive

stop.

• Valve “P” adjusts angle that backcheck is

felt in open cycle. Factory preset is typically

acceptable.

Figure 20 View from ceiling looking down

Figure 21

Chain Protection Plate

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1034-020 Rev 1 10/19 7

6011/6021 Operator LAP Replacement

Power Operator

1. Turn on building power.

2. Turn On/Off switch to “ON” position on conduit assembly.

(Figure 22)

• To scroll through menu items, push up or down on joystick.

(Figure 22)

• To change setting of a menu item, when cursor is on that

item, push joystick right to increase or left to decrease value.

NOTE: Values will auto-save 3 seconds after adjustments.

3. Set ‘HOME’ procedure for door.

• With door closed and selector mode switch of union

assembly in “OFF” position, use joystick to scroll down menu

on LCD screen to “Home”.

• Push in on joystick to activate menu feature. Display changes

to “Set Close Limit”.

• Push in on joystick again, while door is still closed, to set

Home or closed position (Figure 23). Display changes to “Set

Open Limit”.

• Open door to desired open position (Figure 23) and push in

on joystick again. Display changes to “Closing to Home”.

• Allow door to fully close again (Figure 23). Display changes to

“Home”.

NOTE: Values will auto-save.

4. Make necessary adjustments to inverter and add required

accessories.

5. Place selector mode switch of union assembly in ‘ON’ position

for activation by push plate, RF button, or other activation

devices. Place switch in ‘H/O’ for continuous hold open.

(Figure 24) Secure union assembly door with #4 Phillips screw

when nished.

Figure 22 Union Assembly and Spacer not shown

Figure 23

WARNING: Door may begin to move

immediately when power is applied. An

open union assembly door on a PULL unit

has potential to pinch ngers if hand is not

withdrawn quickly when switching on power.

(Figure 24)

Figure 24

WARNING: Door may begin to move immediately when

selector mode switch is changed. An open union assembly

door on a PULL unit has potential to pinch ngers if hand is

not withdrawn quickly when adjusting switch. (Figure 24)

Selector

Mode

Switch

Norton is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 80-9360-1034-020 Rev 1 10/19

Norton Technical Product Support:

Monroe, NC 28112 USA

Phone: 800.438.1951 ext: 6030

TechSupport.Norton@assaabloy.com

nortondoorcontrols.com

You’ve now replaced the 6011 or 6021 Operator LAP.

Attach Cover to nalize installation

1. Align cut-outs in cover to pinion shafts.

(Figure 25)

2. Slide cover onto unit using end cap and union

spacer as guides.

NOTE: Verify all wiring and sheet metal

guards are inside cover.

3. Snap cover securely to backplate. Pull on

cover to verify it is secure.

WARNING: Make sure no wiring is loose or can be

caught by cover when it is snapped into place.

Figure 25

Pinion Shaft Cut-out

Andere Handbücher für Norton 6011 Series

Dieses Handbuch passt für folgende Modelle

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy King 640 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton LEO 5700 Series Kurzanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7900H-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW200i US Handbuch

Assa Abloy

Assa Abloy Norton SafeZone 7100SZ Series Kurzanleitung

Assa Abloy

Assa Abloy Sargent 855 Montageanleitung

Assa Abloy

Assa Abloy Norton UniTrol UNI-1600BC Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SP33-M Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RD150-3 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6000 Series Installationshandbuch

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4600 A Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5630 Series Kurzanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung