Assa Abloy Securitron AQE Series Bedienungsanleitung

AQE-Series

Multi-port Power Over Ethernet Midspan Injector

Installation Manual

500-33600, Rev. A

Notes and Warnings ......................................iii

Symbol Deﬁnitions ............................................................ iii

Warnings.................................................................... iii

Regulatory Information ......................................................... iii

Conventions Used Within this Manual.............................................. iii

Introduction............................................iv

Product Description ........................................................... iv

The AQE Series ............................................................... iv

Section 1 – Installation ....................................1

1.1 Mounting the AQE Rack Mount Supply into a Standard 19" Rack .......................1

1.2 AQE Rackmount Power Supply Overview.........................................2

Section 2 – Initial Conﬁguration ..............................4

2.1 Preparing to conﬁgure the AQE ................................................4

2.2 Logging into AQE Power Supply Control Center for the ﬁrst time ......................4

2.3 Conﬁguring the TCP/IP Settings................................................5

2.4 Conﬁguring the Administration Settings .........................................6

2.5 Conﬁguring the SNMP Settings ................................................6

2.6 Conﬁguring the Email Settings .................................................7

2.7 The Programming Page.......................................................8

Section 3 – Using the AQE ..................................9

3.1 Viewing System Parameters on the AQE Home Page ................................9

3.2 The Tools page ............................................................11

Appendix 1 – Software Agreement and Warranty Statement .......... 12

Table of Contents

500-33600, Rev. A

iii

Notes and Warnings

Symbol Deﬁnitions

The following symbols are used in the Warnings section

below:

hThis symbol alerts the installer of shock hazards

within the enclosure. Service should only be

performed by qualiﬁed service personnel.

iThis symbol alerts the installer of important

information intended to help the installer avoid

personal injury or property damage.

Warnings

hInstallation and service should be performed only

by qualiﬁed service personnel and should conform

to all local codes.

To reduce the risk of electric shock or ﬁre, this

equipment must not be exposed to rain or

moisture.

This equipment shall be installed in a manner which

prevents unintentional operation by employees,

cleaning personnel, or others working in the

premises; by falling objects; customers; building

vibration; or similar causes.

This equipment is not intended for use within the

patient care areas of a health care facility.

Fuses shall only be replaced with the same type and

rating as indicated in the speciﬁcations section of

this manual.

To prevent impaired operation, all wiring is ensured

to be routed and secured to prevent accidental

open or short circuit conditions.

The system and any batteries (if used) should

be tested at least once per year to ensure proper

operation.

Regulatory Information

The equipment discussed within this manual has been

tested to the following standards:

• EN60950 EN55022 CLASS A EN55024

• CSA C22.2 #60950

FCC Information

NOTE: This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may

cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Conventions Used Within this Manual

Positional information (e.g., top, bottom, up, down, left,

right) is referenced with the board or enclosure in the

orientation shown in the illustrations in this manual.

500-33600, Rev. A

Introduction

Product Description

The AQE series of multi-port Power over Ethernet (PoE)

midspan injectors are designed to provide power to

PoE-compatible Internet Protocol (IP) devices such as IP

surveillance cameras, IP phones, door locks, infrared (IR)

illuminators and other PoE-compatible access control edge

devices. The AQE-series products provide 32 watts (W)

of power per port and are compliant with the Institute of

Electrical and Electronics Engineers (IEEE) Standard 802.3,

"Ethernet."

The chart below shows the list of models in the AQE product

family:

The AQE Series

AQE Model No. Description Notes

AQE500R 16 port

32W per port

540W total

Managed midspan injector

Programmable

port priority

AQE250R 16 port

32W per port

270W total

Managed midspan injector

Programmable

port priority

The illustration below shows the model numbering

convention of the AQE series using an example model

number. AQE indicates the model series. The number “500”

indicates a total of 500 Watts nominal output power available.

Currently, 500W and 250W models are available. The letter

“R” indicates rack mount, which is present on all models.

Total output power

AQE 500 R

Product series Rack Mount

Example AQE series model number

Speciﬁcations

Input voltage range 100 – 230 VAC

Input frequency 47 – 63 Hz

Max input current (500W model) 9.0 A

Max input current (250W model) 4.5 A

Power factor > 0.92

500-33600, Rev. A

Use the following procedure when mounting an AQE-series

supply into a standard Electronics Industry Alliance (EIA)

19" equipment rack.

1. If not already completed, securely MOUNT the included

ears to the front of the enclosure sides using the eight

included countersunk screws (four per ear).

2. LOCATE the rack-mounting holes in the ears of the

enclosure. (Figure 1)

3. SLIDE the enclosure into an open 1U location in the EIA

rack

4. CENTER the enclosure in the rack and SECURE with

the four provided 10-32 x 3/4" screws.

NOTE: Rails or other appropriate support for heavy

enclosures shall be used. Heavier components shall be

kept near the bottom of the rack to reduce the risk of

toppling of a top-heavy rack.

1.1 Mounting the AQE Rack Mount Supply into a Standard 19" Rack

The following pages cover the installation of the AQE-series rack-mountable PoE power supplies.

Section 1 – Installation

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

OUT

Figure 1. The Enclosure Mounting Holes

500-33600, Rev. A

1.2 AQE Rackmount Power Supply Overview

345

On / Off

External DC

+–

No user serviceable parts inside

refer servicing to qualified service personnel

Aucune pièce interne ne peut être réparer

Demandez l’assistance d’un technicien qualifié

AC Power

8 7 6

Figure 2: AQE Front View

Figure 3: AQE Rear View

500-33600, Rev. A

1PoE Input / Output (IN / OUT)

There sixteen RJ45 jack pairs (top and bottom pair) labeled

sequentially. For each pair, the bottom jack is for network

data input. The top jack is the data and power output.

CONNECT your data only cables to the bottom row of the

RJ45 jacks (from a network switch, video server, etc.).

CONNECT the top jacks to the corresponding PoE compatible

devices (e.g., IP cameras).

2Ethernet Input (Ethernet)

This port allows users to monitor and control the AQE

multi-port midspan injector through a computer, over a

Local Area Network (LAN) or the Internet. The management

software AQE Power Supply Control Center is web browser

based. You may connect a Personal Computer (PC) directly

to this Ethernet port, or via LAN/Internet.

3External Control (External Control)

This connector allows an external trigger voltage to shutdown

selected PoE outputs (programmed by user via the AQE

Power Supply Control Center management software).

The trigger voltage is 5 to 24V, AC or DC.

4Reset Button (Reset)

Pressing the recessed reset button with a pin for 6 seconds

will reset the IP address and password to the factory default

values.

The factory default IP address is: 192.168.1.9

The factory default user name is: admin

The factory default password is: admin

5Front Panel LEDs (1-16)

The 16 front panel LEDs (labeled 1 through 16) indicate the

port status of the corresponding PoE channels. When the

output is connected to a valid PoE Powered Device (PD)

within the speciﬁed current limit, the LED will be green,

indicating normal operation. When there is a fault condition,

such as when no PD is connected to that port, the LED will

be yellow.

The LED will be turned off if the corresponding port is

disabled by the AQE Power Supply Control Center software.

LED Status Status

Green Normal Operation

Yellow (Fault) No Powered Device connected or fault

condition present

Off Port disabled

When the AQE is ﬁrst powered, these LEDs will light yellow

in sequence (1-16) six times as the unit performs a self-test.

6AC Line Input (AC Power)

This is the connector for the AC line cord.

PLUG the included computer-style line cord into this

connector.

CONNECT the other end of the cord to the power strip inside

the rack or another suitable AC power receptacle. The AQE

series accepts 120–230 VAC ONLY.

7Main AC Power Switch / Circuit Breaker (On/Off)

This is the main AC power switch for the AQE. This switch

lights when power is on and also has a built-in circuit breaker

rated at 15 Amperes (A).

If the circuit breaker trips, RESET it by cycling the switch to

off then back to on.

8External DC Voltage Input (External DC +/-)

This input may be used to either power the AQE via an

external 50 VDC supply or to provide battery backup to the

AQE. The “External DC” input is reverse polarity protected. See

below for details:

To Use Battery Backup

Connect AC power to the AQE unit as normal. In addition,

connect a 48V nominal battery set to the “External DC”

connector, using the battery cable supplied.

To Use an External 50 VDC Supply

Connect a 50V power supply to the “External DC” connector

at the rear. The ratings requirements for the DC power supply

are given below:

Input voltage range 44 – 57 VDC

Max input current (500W model) 14.0 A

Max input current (250W model) 7.0 A

Note that if both AC and DC power sources are connected to

the unit at the same time, the AC source will supply the power

to the output ports. The external DC source will not supply the

outputs unless the AC source is missing or the power switch

is turned off.

The following are basic descriptions. Refer to the appropriate section for more detailed information.

500-33600, Rev. A

2.1 Preparing to conﬁgure the AQE

In order to perform the initial conﬁguration of the AQE, you

will need the following:

• A computer (PC or Mac) set to a static IP address

in the subnet 192.168.1.xxx, where xxx is a subnet

address (0 to 255) not being used by any other

device on the network. DO NOT USE 192.168.1.9 or

the ﬁnal IP address you will be using for the AQE.

(See Figure 4.)

• A web browser installed on the computer.

• A CAT5 or higher Ethernet cable long enough to reach

between the computer and the AQE's Ethernet port.

• The AQE must be powered. After powering the AQE,

WAIT for the AQE to initialize. When ready, the port

LEDs will be lit steady.

After the AQE is powered and initialized, CONNECT the

Ethernet cable between the Ethernet ports of the AQE and

computer. The green LED on the Ethernet port of the AQE

should light. A few seconds later, the yellow LED will begin

ﬂashing.

2.2 Logging into AQE Power Supply Control Center

for the ﬁrst time

From the factory, the AQE is preset with the following settings:

• IP Address: 192.168.1.9

• Username: admin

• Password: admin

OPEN a browser on the computer and enter "192.168.1.9"

into the address bar (not in a search bar - you may need

to disable a "search from the address bar" setting in your

browser, if enabled). A window will appear asking for

authentication (See Figure 5). ENTER "admin" for both the

user name and password. The AQE Home Page should

appear (See Figure 6).

Figure 4: Example of a PC Ethernet port setting window

Figure 5: AQE Power Supply Control Center user login dialog box

Section 2 –

Initial Conﬁguration

The AQE Power Supply Control Center management software allows users to conﬁgure, as well as monitor and control each

output port of the AQE series midspan injector. It is embedded and web browser based and does not require the installation

of any dedicated software on the user's PC. Any PC with an Ethernet port and a common web browser may be used to access

500-33600, Rev. A

2.3 Conﬁguring the TCP/IP Settings

In the orange menu bar at the top of the browser screen,

click the "Conﬁgure" link. Figure 7 shows the Conﬁgure page.

At the top left of the Conﬁgure page is the “TCP/IP Setting”

area. The settings in this area include:

Site ID

Entered by user. ENTER any meaningful name to identify

the AQE midspan unit. This name will be displayed on

the HOME page.

IP Address

The factory default IP address is set to 192.168.1.9. This

address may be changed to any valid IP address. SET the

ﬁrst three values of the IP address to match the domain

of the network to which the AQE will be connected. SET

the ﬁnal value to a number between 0 and 255 which is

not being used by any other device on the subnet. In the

event the IP address is later forgotten, PRESS the “Reset”

button on the front panel of the AQE for 6 seconds and the

IP address, default user name, and default password will be

reset to factory default values.

Net Mask

Should typically be set to 255.255.255.0

MAC address

The MAC Address is factory set and is not programmable

by the user.

Gateway IP

The default gateway is 192.168.1.1. This value may be

changed by the user - consult with your IT department

for more information.

DNS0, DNS1

The default value for DNS0 and DNS1 are 192.168.1.1.

These values may be changed by the user - consult with

your IT department for more information.

Figure 6: AQE Power Supply Control Center opening (HOME) page

500-33600, Rev. A

Enable DHCP

Normally, this option is left unchecked, however in some

cases you may want to allow the network to assign an IP

address to the AQE. However, please note that once you

select this option, you will need a network scanning

tool to ﬁnd the AQE's IP address before you will be able

to log into the AQE and that the IP address of the AQE

may change periodically.

You must click the “Submit” button at the bottom right of this

area to save the changes in this section. The new setting will

take effect after the AQE product is power cycled, or rebooted.

2.4 Conﬁguring the Administration Settings

On the top right of the Conﬁgure page is the “Administration

Setting” area. The settings in this area include:

Admin User Password

The default password for the admin account is admin. This

may be changed to any password of at least 5 characters.

ENTER the new password into the "Admin User Password"

ﬁeld. If changing the password, ENTER it again into the

"Verify Admin Password" ﬁeld. These two ﬁelds must match

in order to successfully change the password. CLICK the

"Submit" button - a popup message will conﬁrm a successful

password change. When you leave the conﬁgure page, the

AQE will ask you to re-log in.

Insert Date

ENTER the correct date in the speciﬁed value ﬁeld. It

should be noted that the format is YYYY-MM-DD. For

example, for February, you should enter “02” not “2”.

Insert Time

ENTER the correct time in the speciﬁed ﬁeld. The format

is HH:MM:SS.

CLICK the “Submit” button to save the time and date

settings.

2.5 Conﬁguring the SNMP Settings

In the SNMP Setting block, under the "Basic" heading, SET

Community to "public" and SET Location to a meaningful

name of your choice. This entry will help you identify

the speciﬁc AQE when multiple AQEs are installed on

the same subnet. In the example, "LSP" is entered. This

entry will be read by an SNMP system as "syslocation,"

OID .1.3.6.1.2.1.1.6. The default port for SNMP is Port 161.

Be sure to open the SNMP port if accessing SNMP outside

your ﬁrewall. CLICK the "Submit" button at the bottom of the

"Basic" section to save the settings, otherwise you will lose

Figure 7: Top half of the AQE Power Supply Control Center Conﬁgure page

500-33600, Rev. A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Laborausrüstung Handbücher

Assa Abloy

Assa Abloy SECURITRON AQE15 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung