Assa Abloy 9800 TCNE1 Series Bedienungsanleitung

Installation Instructions

for 9800 TCNE1 Series Trim by ED5200N (S) (A)

and 9M800 TCNE1 Series Trim by ED5600N (A) with

Rim, SecureBolt™, and Mortise Exit Devices

Important: The accuracy of the door preparation is critical for proper functioning and security of this trim.

Misalignment can cause premature wear and a lessening of security.

Please read these instructions carefully to prevent missing important Steps.

Please Note: Improper installations may result in damage to the lock and void the factory warranty.

FM242B 12/08 (617417610)

123

For installation assistance contact Corbin Russwin Inc. at 1-800-810-WIRE (9473).

CAUTION

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

TEST

FOR PROPER

OPERATION

BEFORE

CLOSING

DOOR

1) Warning

General Description

Features / Specifications

Rim & SecureBolt™ TCNE1 Series Product Illustration

5) Switch Settings(Rim & SecureBolt™)

Installation Instructions

Mortise TCNE1 series Product Illustration

Table of Contents

Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

1) Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that the interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

•Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced TV technician for help

This Class B digital apparatus complies with Canadian ICES-003.

Page

5 - 11

6.1) Before Starting

6.2) Attaching the Fire Stop Plate

6.3) Trim Assembly Instructions

6.4) Installation of Outside Trim and Exit Device

6.5) Installation of Outside Keypad Escutcheon

6.6) Installation of Inside Controller Escutcheon and Electrical Connections

6.7) Cover Installation

7 - 8

•

7.1) Before Starting

7.2) Attaching the Fire Stop Plate

7.3) Installation of Mortise Lock

7.4) Installation of Outside Trim and Exit Device

7.5) Installation of Cylinder and Outside Keypad Escutcheon

7.6) Installation of Inside Controller Escutcheon and Electrical Connections

7.7) Cover Installation

8) Operational Check20

15 - 16

General Description

2) General Descriptions

The Access 800®TCNE1 Rim, SecureBolt™ and Mortise Exit Device offers the ability to seamlessly

integrate Grade 1 security into an existing Wiegand compatible access control system. Monitoring capabilities

for Rim and SecureBolt include Request to Exit and Door Position Switch. Note:Mortise Exit devices offer

Request to Exit and Door Position Switch and can monitor the latchbolt and/or Deadbolt of the Mortise Lock

when connected to the Auxiliary Relay Module incorporated into the Network Interface Cabinet.

Features

• Complete monitoring of doors from locks

• Network Interface board connects to most third party access control points

• Panel interface board accommodates up to 4 locks

• HID 125khz proximity credentials

• Supports Fail-Safe and Fail-Secure 24VDC Solenoid Locking Devices

3) Features / Specifications

Access

Control

Panel

NETWORK INTERFACE

CABINET

****

Items Supplied with Exit Device

Items included with ED5200N(S) (A) Rim or Items included with ED5600N (A) Series

SecureBolt Exit Device by9800 TCNE1Mortise Exit Device by 9M800 TCNE1

• Outside Escutcheon with Keypad • Outside Escutcheon with Keypad

• Outside Solenoid Trim Assembly • Outside Solenoid Trim Assembly

• Exit Device • Exit Device

• Inside Escutcheon with Circuit Board • Inside Escutcheon with Circuit Board

• Screw Pack • Screw Pack

Specifications

• Latch – 3/4" throw, stainless steel • Latch 3/4" throw, anti-friction, stainless steel

• Outside Solenoid driven lever controlled by keypad • Outside Solenoid driven lever controlled by keypad

• Push bar retracts latch from inside • Push bar retracts latch from inside

• Fire stop provided for fire rated doors • Fire stop provided for fire rated doors

• Exit devices furnished for 1 3/4" – 2 1/4" doors

• Exit devices furnished for 1-3/4" - 2 1/4" doors

• UL Listed

• Accepts all Corbin Russwin Inc. mortise cylinders

• Accepts all Corbin Russwin Inc. rim cylinders

(9M805 only)

(9803 only)

• Key retracts latch (9M805 only)

• Key allows lever to retract latch (9803 only)

• Available in all lever handle designs

Series TrimSeries Trim

• Weatherseal gaskets and conduit • Weatherseal gaskets and conduit

Specifications

4) 9800 TCNE1 Series Trim Product Illustration (Rim and SecureBolt™)

SecureBolt™ Shown

Tailpiece

must be

in vertical

position

Trim

Gasket

Inside

Door

Cover

(2) Finish Washers

Head Screws

(2) 1/4 - 20 Oval

Ground

Wire

8 Pin

Molex

Doorwire

2 Pin

Methode

Solenoid

2 Pin

Molex REX

(2) 1/4 - 20 Pan

Head Screws

5) Switch Settings

(Rim, SecureBolt™ and Mortise)

Switch Settings

This device has been shipped from the factory with switch settings configured

as follows:

Reader Dip-Switch Settings at Switch S1:

Reader Dip-Switch Settings at Switch S2:

Dip-Switch 1 and 2 – OFF, indicating Reader Address #1

Note: To gain access to switch S2 remove the black cover from the inside escutcheon

with the High Security T20 Torx bit provided.

Reader Switch S1 is located

in the lower left corner on the

back of the Reader.

Reader Switch S2 is located

in the lower right corner on

the front of the Reader.

Dip-Switch 4 – ON Solenoid Operation selected

Dip-Switch 5 – ON or OFF based on Fail Safe or Fail Secure per order requirements

Dip-Switch 6 – OFF Red LED

Dip-Switch 7 – OFF Tamper Input Select Disabled

Both Switch 1 and 2 are shown

in the open position indicating

that the reader is set to be

Reader address #1.

Verify hand and bevel of door. Door should be fitted and hung.

Verify box label for size of exit device, function and hand.

6) Installation Instructions (Rim and SecureBolt™)

Prep door according to supplied Corbin Russwin Inc. door marker template.

Outside

Inside

LeftHand

Reverse

"LHR"

Right Hand

Reverse

"RHR"

7/8"

1-1/2"

1/8" Dia. holes

(2) required

Fire Stop Plate

Slot

Attach Fire Stop Plate

Using self tapping screws

#8x1/2" long for wood and

metal doors

C of 1-1/2" Dia.

Fire Rated Door

Hole for ribbon cable

Outside

of door

Non Fire Rated Door

Outside

of door

Install conduit half with recessed

panel "Not For Use On Fire Door"

visible from outside of door.

Installation of the Conduit

(provided) is recommended when

the device is installed in a non fire

rated exterior door. The conduit is

part of a Weatherseal Gasketing Kit.

This kit can be ordered separately,

order part number 794F909.

6.1)

6.2)

1.Check cylinder components.

NOTE: Cylinders longer than 1-1/8" (29mm) will require collars.

Refer toCylinder Collar Chart below.

2. When required, cut cylinder tailpiece.

Correct length is 1/16" to 3/16" (2 to 5mm) beyond cylinder housing cam.

3. Assemble cylinder.

Insert cylinder housing prongs into matching notches of escutcheon.

Pass cylinder tailpiece thru cylinder collar (when required)and slot

in cylinder cam. Fasten cylinder in escutcheon recess or collar

using (2) mounting screws.

(DO NOT OVER TIGHTEN SCREWS).

6) Installation Instructions (Rim and SecureBolt™)

Cylinder

Tailpiece

Cylinder Collar

(when required)

Cam must be positioned as shown

when cylinder tailpiece is assembled

Escutcheon Assembly

Lever is handed,LHR (shown).

NOTE:Lever Return Spring is handed.

Hand of trim cannot be changed without

correct spring.

LHR, part number 651F618 (Red)

RHR, part number 651F628 (Blue)

Cylinder Housing Cam

(2) Cylinder Mounting Screws.

Supplied with cylinder

Cylinder Collar Chart

Cylinder length Collar

1-1/8" (29) None

1-1/4" (32) 422F88*

1-1/2" (38) 686F98*

* Specify Finish

Rim Cylinder

Lever Return Spring handing can be identified

by the color of the spring:

6.3)

6) Installation Instructions (Rim and SecureBolt™)

Cover

Trim Assembly

Tailpiece

must be

in vertical

position

(2) Finish Washers

Head Screws

Solenoid Wire

Harness

Trim

Gasket

CAUTION

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

(2) 1/4 - 20 Oval

(2) 1/4 - 20 Pan

Head Screws

TRIM GASKET APPLICATION:

Peel off the adhesive protective paper

from gasket. Feed Trim assembly solenoid

wire harness through gasket opening as

shown and firmly press gasket to

escutcheon, aligning edge of gasket with

the edge of the escutcheon.

Inside

Door

6.4) Installation of Outside Trim and Exit Device

Outside Trim Assembly

1. For exterior door applications, it is recommended that the Trim Gasket

(provided) be applied as shown below.

2. Route the 2 pin REX (Request to Exit) connector harness into the Trim Assembly cavity in

the door and up thru the door and out the 1/2” diameter Hole “C”.

3. Route the Trim Assembly 2 pin connector of the Solenoid wire harness into the trim

assembly cavity in the door and out the 1/2” diameter hole “C”. Be careful not to pinch any

wire harness wires.

4. When mounting trim, lift tailpiece to pass through hole on device side. Be sure tailpiece is

in vertical position.

5. Fasten trim assembly through holes “A” using (2) 1/4” – 20 oval head screws and (2) finish

washers. Finger tight only!

8 Pin

Molex

Doorwire

2 Pin

Methode

Solenoid

2 Pin

Molex REX

6) Installation Instructions (Rim and SecureBolt™)

Cover

Trim Assembly

Tailpiece

must be

in vertical

position

(2) Finish Washers

Head Screws

Solenoid Wire

Harness

Trim

Gasket

CAUTION

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

(2) 1/4 - 20 Oval

(2) 1/4 - 20 Pan

Head Screws

TRIM GASKET APPLICATION:

Peel off the adhesive protective paper

from gasket. Feed Trim assembly solenoid

wire harness through gasket opening as

shown and firmly press gasket to

escutcheon, aligning edge of gasket with

the edge of the escutcheon.

Inside

Door

6.4) Installation of Outside Trim and Exit Device

Outside Trim Assembly

1. Seal device against door being careful to align vertical trim tailpiece to

engage with cross hole of device cam.

2. Fasten device to trim assembly through holes “B” using (2) 1/4 – 20 pan head screws.

3. Follow instructions packed with device to secure device to door. Tighten all screws.

2 Pin

Methode

Solenoid

8 Pin

Molex

Doorwire

2 Pin

Molex REX

6) Installation Instructions (Rim and SecureBolt™)

2a. For fire rated devices, feed keypad ribbon cable/connector and ground wire from

outside of door through fire stop plate and hole in door.

2b. For non fire rated exit devices, feed keypad ribbon cable/connector and ground wire

through the door.

Place escutcheon against door surface.

GASKET APPLICATION:

Peel off the adhesive protective paperfrom

gasket. Feed Keypad ribbon cable and ground

wire through gasket opening as shown and firmly

press gasket to escutcheon, aligning edge of

gasket with the edge of the escutcheon.

Ground Wire

Keypad Ribbon Cable

Outside

Door

Fire Stop Plate

6.5) Installation of Outside Keypad Escutcheon

1. For exterior door applications, it is recommended that the gaskets provided

be applied as shown. The gaskets may be used as a seal between the escutcheon

and the door surfaces.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Corbin Russwin UT5200 Series Kurzanleitung

Assa Abloy

Assa Abloy Securitron SAM Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL420 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron TJ-38 TOP JAM KIT Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL428 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lever YRL256 Technische Daten

Assa Abloy

Assa Abloy hes RF0010 Betriebsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy MGL-01500ALS Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 3P82TSS-A11E Bedienungsanleitung

Assa Abloy

Assa Abloy YALE 4600CK Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Passport 1000 PG Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON FM9930 Bedienungsanleitung

Assa Abloy

Assa Abloy 836S Bedienungsanleitung

Assa Abloy

Assa Abloy Zi IKON CLIQ Go Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Real Living YRC246 Technische Daten

Assa Abloy

Assa Abloy Corbin Russwin IN120 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT DL Series Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS200-640 Bedienungsanleitung

Assa Abloy

Assa Abloy Access Control Electric Locking Handbuch

Assa Abloy

Assa Abloy EMTEK EMTouch Classic Style Betriebsanleitung

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 809M Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung