Assa Abloy SARGENT DL Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com A7858F 10/20

Installation Instructions

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

DL Series

Tubular Lock

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

Installation Instructions

• #2 Phillips screwdriver

• T20 sized security bit

1Tools Required

2Package Contents

Figure 1 Part No. Description Qty

1 — Lever 2

2 82-1038 Set Screw 2

DL-2053* Rose Assembly -- CO Design

(15 Function) 2

DL-2054* Rose Assembly--CO Design

(65 Function) 2

DL-2055* Rose Assembly -- TO Design

(15 Function) 2

DL-2056* Rose Assembly -- TO Design

(65 Function) 2

DL-2057* Rose Assembly -- O Design

(15 Function) 2

DL-2058* Rose Assembly -- O Design

(65 Function) 2

DL-2059* Rose Assembly -- LN Design

(93 & 94 Functions Only) —

DL-2060* Rose Assembly -- CR Design

(93 & 94 Functions Only) —

DL-2061* Rose Assembly -- TR Design

(94 & 94 Functions Only) —

DL-2113* Rose Assembly -- E2 Design

(15 Function) 2

DL-2114* Rose Assembly -- E2 Design

(65 Function) 2

DL-2115* Rose Assembly -- E2 Design

(93 & 94 Functions Only) 2

4 82-0017 Mounting Post 2

Figure 1 Part No. Description Qty

DL-2005 Spring Housing 2

DL-0091 Mounting Plate

(93 & 94 Functions Only) —

DL-2006* Mounting Assembly/Blank Rose (15-3

Function) —

82-4022* Thru-bolt Plate Assembly

(TB-93 Function) —

6 82-0347 Lever Springs 2

DL-5007* Latch -- 2-3/4" Backset

(15 Function) 1

DL-5008* Latch -- 2-3/4" Backset

(65 Function) 1

DL-5009* Latch-- 2-3/8" Backset

(15 Function) 1

DL-5010* Latch -- 2-3/8" Backset

(65 Function) 1

808-3788* T-Strike Screw Pack 1

08-2853 28- Prefix Screw Pack (not shown) 1

800* Standard T-Strike 1

808* 28- Prefix ANSI Strike (not shown) 1

505* 13- or 14- Prefix Full Lip Strike (not

shown) 1

10 AM-0044 Wrought Box Strike 1

11 DL-0023* Push Button (65 Function Only) 1

12 DL-2020 Mounting Post Screw Pack 1

* Specify Finish

• 1/8" drill bit

• 2-1/8" drill bit

• 1" drill bit

DL Series

Installation Instructions

A7858F 10/20

1-800-727-5477 • www.sargentlock.com

Tubular Lock

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

• Hollow Metal Doors should be properly reinforced for lock support. If support is not provided, contact door

manufacturer.

• For all metal door preparations, use 7 line template (A7240) for reference

• For all wood door preparations, use template A6719 (Except for functions DLU93 / DLU94 which uses

template A7931)

3Door and Frame Preparation

1. Mark and Drill Holes 2. Final Door Prep 3. Frame Preparation

4Installation

Install loosely;

Tighten after step #2

Screws

(2) #8-32 x 3/4"

Install Latch and Outside Assembly

Note: These instructions are used for the following functions:

DLU15, DLU65 and DLU15-3.

1. Install Latch

2. Slide outside assembly into the bore

Note: For the DLU65, the threaded hole on locking piece must

be toward the inside of the door, so the Push Button can be

threaded into it (as shown on other side)

Install Inside Assembly

1. Install Mounting Plate Assembly

A. Locate holes in mounting plate assembly over

center punch marks.

Note: Location of set screw

B. Install (2) combo screws and tighten to secure

mounting plate assembly to door

2. Install Rose & Lever

A. Install rose onto mounting plate assembly and

rotate clockwise to tighten.

B. Install lever onto spindle. Insert setscrew into

hole in lever and tighten.

Note: For square rose installation, see page 3.

Screws

(2) #8 x 3/4"

Scalp to be removed with flat headed screwdriver at

notch

IMPORTANT

Test for proper

operation before

closing door

A7858F 10/20

1-800-727-5477 • www.sargentlock.com

DL Series

Installation Instructions

Tubular Lock

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

4Installation, Continued.

Install DLU93

1. Install Mounting Plate Assembly

A. Locate holes in mounting plate assembly over center punch marks.

Note: Location of set screw

B. Install (2) combo screws and tighten to secure mounting plate assembly

to door

2. Install Rose & Lever

A. Install rose onto mounting plate assembly and rotate clockwise to

tighten

B. Install lever onto spindle. Insert setscrew into hole in lever and tighten.

93 Function Parts List Description: 1-Mounting plate assembly, 2-Combo screws (2), 3-Rose, 4-Lever, 5-Set screw

Install TB-DLU93 & DLU94

1. Install Thru-Bolting Assembly

A. Locate studs from Rose Assembly or O/S Thru Bolt Plate

Assembly into 1/4" drill holes on outside of door

B. Locate Mounting Plate Assembly on inside of door.

Install (2) machine screws and tighten to secure.

2. Install Rose & Lever

A. Install rose onto mounting plate assembly and rotate

clockwise to tighten.

B. Install lever onto spindle. Insert setscrew into hole in lever

and tighten. Repeat process for Outside Lever (94 Function

only).

94 Function Parts List Description: 1-Mounting Plate Assembly, 2-#6 X 3/4" Machine Screws (2), 3-Rose, 4-Lever(2),

5-Set screw (2), 6-Rose Assembly

TB- 93 Function Parts List Description: 1-Mounting Plate Assembly, 2-#6 X 3/4” Machine Screws (2), 3-Rose, 4-Lever,

5-Set screw, 7-Outside Thru-Bolt Plate Assembly

5Square Rose Installation

TOP

HINGE

1. Install lock per instructions on page 2. Square rose installation begins after spring housing installation.

2. Position square mounting plate over spring housing as seen in Figure 1 on page 4.

3. Drill two centered pilot holes for the #6 mounting screws in the upper right and lower left portions of the square

mounting plate.

4. Loosely attach mounting plate to both sides of the door with screws.

5. Square top surface of mounting plate to edge of door

NOTE: The right angled square MUST be on the flat surface

of the square mounting plate for proper leveling.

6. Tighten mounting screws

7. Press rose onto mounting plate, fasten lever with set screw.

Parts List Description: 1-Square mounting plate,

2-#6 x ¾" Machine Screws (2), 3-Rose, 4-Lever (2), 5-Set Screw (2)

Tools Needed: Drill, Pilot bit, Phillips screw driver,

Right angle square

A7858F 10/20

SARGENT Manufacturing Company

100 Sargent Drive

New Haven, CT 06511 USA

800-727-5477

www.sargentlock.com

1-800-727-5477 • www.sargentlock.com

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

5Square Rose Installation, continued

Figure 1 Note: To level plate, place a right angle square on the flat

portion of the mounting plate.

Spring Housing Square Mounting Plate

Pilot Hole

TOP

HINGE

Dieses Handbuch passt für folgende Modelle

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy MUL-T-LOCK SC110 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent V.S2 Bedienungsanleitung

Assa Abloy

Assa Abloy 3090 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living B1L Z-Wave Technische Daten

Assa Abloy

Assa Abloy Securitron GL1 Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL590 Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON MORTISE UNLATCH MUNL-12 Bedienungsanleitung

Assa Abloy

Assa Abloy MGL-01500ALS Series Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON 32 Series Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 819N Bedienungsanleitung

Assa Abloy

Assa Abloy hes 8000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock SL YRD256 Technische Daten

Assa Abloy

Assa Abloy SARGENT Profile v.G1.5/LK Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Signature Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Delayed Egress 57-80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron CEPT-10-10 Bedienungsanleitung

Assa Abloy

Assa Abloy EL595 Bedienungsanleitung

Assa Abloy

Assa Abloy Code Handle Window Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron SAM Bedienungsanleitung

Assa Abloy

Assa Abloy EMTEK EMPowered Motorized Smart Lock Upgrade... Bedienungsanleitung

Assa Abloy

Assa Abloy 836S Bedienungsanleitung

Assa Abloy

Assa Abloy d12-B2 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent IN100 Bedienungsanleitung

Assa Abloy

Assa Abloy ELECTRIC LOCK Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung