Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

FM483 11/18

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

TOC Table of Contents

M, N and P

Escutcheon Trim

ML2000 Series Mortise Locks

Mortise Lock Handing Instructions............................... 2

M, N and P Escutcheon Installation .............................. 3

Half Active M, N and P Escutcheon Installation ...................... 5

Full Dummy M, N and P Escutcheon Installation ..................... 7

Half Dummy M, N and P Escutcheon Installation ..................... 8

Installing Knobs Sold Before October 2017 ONLY: .................... 8

For Museo® Series Designer Trim,

refer to installation instructions FM601.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

2FM483 11/18

M, N and P Escutcheon Trim

Installation Instructions

ML2000 Series Mortise Lock

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

MAKE SURE CATCH PLATE IS

EVEN W/ TOP SURFACE

GOOD BAD

WARNING:

LOCK-IN CAN

OCCUR IF LATCH

IS NOTPROPERLY

INSTALLED

4. Push in latch while holding

screwdriver behind latch tail.

(Figure 8)

5. Rotate lock front to match bevel of door,

as shown. (Figure 10)

1 Mortise Lock Handing Instructions

Figure 1

Figure 2

Figure 3

RED Locking Screw

Catch Plate

LOCK HANDING

IS CRITICAL TO

ENSURE LOCK

FUNCTIONS

PROPERLY

Figure 4

1. Move red locking screw to side of lockbody

being locked.

2. Push in latch. Depress catch plate with

screwdriver. (Figure 1)

3. Pull latch out of lock-body and turn latch

over. (Figure 2)

Figure 5

NOTE:

Push in latch until catch plate is

no longer depressed. (Figure 4)

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

3FM483 11/18

M, N and P Escutcheon Trim

ML2000 Series Mortise Lock

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 M, N and P Escutcheon Installation

1. Install strike using shorter 3/4" strike

mounting screws. If strike box is

needed, insert between strike and door

frame. (Figure 6)

2. Insert mortise lock into door and hand tighten

longer 1" mounting screws. (Figure 7)

3. Install outside and inside adapter plates.

(Figure 8)

4. Mount escutcheons. (Figure 9)

5. Install outside lever or knob by inserting

adjustment bolt on opposite side of door.

Tighten bolt ﬁnger-tight and then loosen a

few turns. (Figure 10)

NOTE:

Make sure lock is unlocked. If lock has a

toggle, push bottom of toggle inward to

unlock during installation.

Figure 6

Figure 7 Figure 8

Figure 9

NOTE:

Make sure turn-piece is oriented vertically

when installing escutcheon.

Turn-Piece

Outside

Inside

Narrower Hole

Wider Hole

Strike Lip

Strike Orientation

Figure 10

NOTE:

Use correct spindle orientation.

(Figure 11)

Knob

Lever

Spindle

Adjustment

Bolt

Outside

Use Correct Spindle Orientation

Lever

GOOD

BAD

Figure 11

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

4FM483 11/18

M, N and P Escutcheon Trim

Installation Instructions

ML2000 Series Mortise Lock

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 M, N and P Escutcheon Installation, (cont.)

NOTE:

Make sure adjustment bolt hole is aligned

with lever or knob hole. (Figure 13)

LeverLever Lever

Adjustment

Bolt

Adjustment

Bolt

Adjustment

Bolt

Misaligned.

Adjustment bolt needs to

be threaded in farther.

Misaligned.

Adjustment bolt needs to

be unthreaded.

Adjustment bolt fully

aligned with lever hole and

ready to be secured with

set screw.

6. Install inside lever or knob by inserting

dowel screw. (Figure 12)

Figure 12

Figure 13

NOTE:

• Pull key slightly out of cylinder to

help thread into lockbody.

• Cylinder must be oriented correctly.

(Figure 15)

Key and cylinder

must be rotated

as shown.

Correct Incorrect

ASSA ABLO Y

ASSA ABLOY

7. Install cylinder. Secure with cylinder set

screw. (Figure 14)

Figure 14

Figure 15

8. Tighten lock mounting screws.

9. Install armored front. (Figure 16)

Figure 16

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

5FM483 11/18

M, N and P Escutcheon Trim

ML2000 Series Mortise Lock

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Half Active M, N and P Escutcheon Installation

1. Install strike using shorter 3/4" strike

mounting screws. If strike box is

needed, insert between strike and door

frame. (Figure 17)

2. Insert mortise lock into door and hand

tighten longer 1" mounting screws.

(Figure 18)

3. Install inside adapter plate.

(Figure 19)

4. Mount escutcheon. (Figure 20)

5. Insert adjustment bolt and spindle. Tighten

bolt ﬁnger-tight and then loosen a few

turns. (Figure 21)

NOTE:

Make sure lock is unlocked. If lock has a

toggle, push bottom of toggle inward to

unlock during installation.

Figure 17

Figure 18 Figure 19

Use Correct Spindle Orientation

Lever

GOOD

BAD

NOTE:

Use correct spindle orientation. (Figure 22)

Figure 20

Figure 21

Figure 22

Spindle

Adjustment

Bolt

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

6FM483 11/18

M, N and P Escutcheon Trim

Installation Instructions

ML2000 Series Mortise Lock

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

7. Install inside lever or knob by inserting

dowel screw. (Figure 23)

3Half Active M, N and P Escutcheon Installation, (cont.)

8. Tighten lock mounting screws.

9. Install armored front. (Figure 25)

NOTE:

Make sure adjustment bolt hole is aligned with

lever or knob hole. (Figure 24)

LeverLever Lever

Adjustment

Bolt

Adjustment

Bolt

Adjustment

Bolt

Misaligned.

Adjustment bolt needs to

be threaded in farther.

Misaligned.

Adjustment bolt needs to

be unthreaded.

Adjustment bolt fully

aligned with lever hole and

ready to be secured with

set screw.

Figure 23

Figure 24

Figure 25

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.

the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

7FM483 11/18

M, N and P Escutcheon Trim

ML2000 Series Mortise Lock

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4 Full Dummy M, N and P Escutcheon Installation

1. Install outside and inside adapter plates.

(Figure 26)

2. Mount escutcheons onto adapter plates.

(Figure 27)

3. Install outside lever or knob by inserting

adjustment bolt on opposite side of door.

Tighten bolt ﬁnger-tight then loosen a few

turns. (Figure 28)

Figure 26

Figure 27

NOTE:

Use correct spindle orientation.

(Figure 29)

Use Correct Spindle Orientation

Lever

GOOD

BAD

Figure 29

Figure 28

Spindle

Adjustment

Bolt

Knob

Lever

NOTE:

Make sure adjustment bolt hole is aligned

with lever or knob hole. (Figure 31)

LeverLever Lever

Adjustment

Bolt

Adjustment

Bolt

Adjustment

Bolt

Misaligned.

Adjustment bolt needs to

be threaded in farther.

Misaligned.

Adjustment bolt needs to

be unthreaded.

Adjustment bolt fully

aligned with lever hole and

ready to be secured with

set screw.

4. Install inside lever or knob by inserting

dowel screw. (Figure 30)

Figure 30

Figure 31

FM483 11/18

Corbin Russwin

225 Episcopal Road

Berlin, CT 06037

Phone: 800-543-3658

Fax: 800-447-6714

corbinrusswin.com

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group,

written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

4. Install mounting screws and washers for

the escutcheon. (Figure 35)

5. Install inside lever or knob by inserting

dowel screw. (Figure 36)

Figure 35

Figure 36

5 Half Dummy M, N and P Escutcheon Installation

1. Assemble and install outside dummy

adapter plate. (Figure 32)

2. Install mounting screws and washers for

the adapter plate. (Figure 33)

3. Mount escutcheon. (Figure 34)

Figure 32

Figure 33

Figure 34

6 Installing Knobs Sold Before October 2017 ONLY:

Before inserting knob lockbody into door, push

spacer out of lock using a screwdriver.

(Figure 37)

Figure 37

Spacer

NOTE:

Install spindles in square orientation.

(Figure 38)

STANDARD MUSÉO

Lever

GOOD

BAD

Figure 38

Andere Handbücher für Corbin Russwin BLSS ML2000 Series

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy 3090 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale inTouch Technische Daten

Assa Abloy

Assa Abloy hes RF0010 Betriebsanleitung

Assa Abloy

Assa Abloy Aperio Series Bedienungsanleitung

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy ELECTRIC LOCK Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON 32 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy INTERLOCK P84166 Bedienungsanleitung

Assa Abloy

Assa Abloy ASSA Coded 1.2 Installationshandbuch

Assa Abloy

Assa Abloy Yale Smart Latch Bedienungsanleitung

Assa Abloy

Assa Abloy HES 660 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent FM6100 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 809M Bedienungsanleitung

Assa Abloy

Assa Abloy MUL-T-LOCK SC110 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale P117 Bedienungsanleitung

Assa Abloy

Assa Abloy Assa compact 3000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Passport 1000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 5300LN Series Kurzanleitung

Assa Abloy

Assa Abloy K100-622 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Signature Series Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS200-640 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Profile v.G1.5/LK Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung