Assa Abloy Arrow AL-500 Series Bedienungsanleitung

A8265A 08/19

Installation Instructions

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

AL-500 Series

Alarmed Exit Devices

ATTENTION INSTALLER

Disconnect all input power before beginning installation

to prevent electrical shock and equipment damage.

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

TOC Table of Contents

1 General Description .............................................................3

2 Miscellaneous Parts .............................................................3

3 Dip Switch (SW-2, 6-position) ...................................................3

4 AL - Circuit Board ................................................................4

5 Apply Rail Assembly .............................................................5

6 Installation Instructions .........................................................5

a Door Preparation................................................................6

b Add or Remove Cylinder.........................................................6

c Installation and Orientation of Cylinder ..........................................6

7 Alarmed Exit (AL500) Standard Operating Instructions...........................7

a Arm Alarm ......................................................................7

b Security/Tamper Violation .......................................................7

c Low Battery Alert ...............................................................7

8 Optional Features ...............................................................8

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

1 General Description

The Alarmed Exit is designed for areas that require an alarm to sound upon exiting. Once armed, any push

rail movement will activate the horn in the push rail. The horn will continue to sound for two (2) minutes

and shut off automatically. The LED will flash, indicating a violation has occurred.

Alarmed Exit

Circuitry Figure1

Manual dogging is provided standard

on non fire rated devices

2 Miscellaneous Parts

Endcap

Mounting PlateExit Rail

Exit device

chassis and rail

assembly shown

Chassis

Assembly

Cover Mounting rail insert

Figure2

3 Dip Switch (SW-2, 6-position)

Factory settings shown.

1. DS-1 = OFF, DS-2 = OFF - REX / Passage Delay (set to 7 seconds).

2. DS-3 = OFF, DS-4 = OFF - Automatic Alarm Reset (set to 2 minutes).

3. DS-5 = ON - Selects LED color (Armed = Green, Violation = Red, Passage = Yellow).

4. DS-6 = ON - Monitor Relay is enabled (will activate when rail is violated).

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

4 AL - Circuit Board

Printed Circuit Board:

Figure3

Note

SW-1, Arm/Disarm Switch shown in ON (armed) position.

Insert with circuit board:

Battery

Figure4

OFF

SW-2 6-position

dip switch

SW-1

Arm/Disarm

switch

6 5 4 3 2 1

Figure5

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

5 Apply Rail Assembly

1. Depress lift arm into rail assembly and slide rail onto chassis.

2. Attach rail assembly to chassis with two (2) #8 truss head machine screws. Do not tighten screws

(Figure6).

3. Secure chassis to door with four (4) #10 flat head screws. (Figure8)

4. Level rail.

5. Place mounting plate tight against rail and attach to door with two (2) #10 round head screws.

6. Tighten all screws securely (Figure7).

Figure6

Lift Arm Level Mounting Plate

Rail Assembly

Rail Mounting Screw (2 Places)

(#8-32 x 3/8 PH. Truss HD. Machine Screw)

Mounting Plate

Mounting Plate Screws

(#10-24 x 3/4"PH. RD. HD. Machine Screw)

Figure7

Chassis Mounting Screws

(1/4-20 x5/8 PH. FL. HD.

Machine Screws)

Four (4) places

Figure8

6 Installation Instructions

• These instructions are for the AL500 Series exit device, which is designed for areas requiring field

selectable time delay and automatic alarm reset options.

• Verify hand and bevel of door. Exit devices are always reverse bevel and mounted on inside of door.

Left Hand Reverse Bevel Hinges

Left. Open Outward LHRB

Inside View Outside View Inside View Outside View

Right Hand Reverse Bevel Hinges

Left. Open Outward RHRB

LHRB Shown RHRB Shown

Figure9

1. Installation must be performed by a trained and experienced service person.

2. 9V battery operated.

3. No external wires.

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

6 Installation Instructions (cont.)

a Door Preparation

1. Prepare door according to template.

2. Verify size 1-1/8” cylinder is installed in rail insert with collar prior to installing exit device on door.

NOTE: Use caution not to damage wires when installing cylinder nut.

Collar

Cylinder nut

Side View. Battery holder

not shown.

Use caution not to dam-

age wires when installing

cylinder nut.

Figure10

b Add or Remove Cylinder

1. Remove insert assembly from rail by sliding toward rail end (Figure11).

Figure11

c Installation and Orientation of Cylinder

1. Slide cylinder through collar into insert

as shown (Figure12).

2. Note orientation of cylinder.

3. Secure cylinder with cylinder nut,

tightening firmly.

4. Operate cylinder and verify cam is

operating switch properly (Figure13).

Figure12

Figure13

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

7 Alarmed Exit (AL500) Standard Operating Instructions

a Arm Alarm

Turn key clockwise. Yellow PASSAGE LED will flash for 15 seconds (default),

then a quick chirp and ARMED green LED will flash and repeat every

30 seconds. Signal above cylinder indicates unit is armed (Figure14).

NOTE:

Unit is automatically armed 15 seconds after it is turned on.

Field selectable settings listed at bottom of page.

b Security/Tamper Violation

When ARMED, depressing the push rail will activate alarm. Horn will

sound and red violation LED will flash. The horn will continue to sound

for two (2) minutes (default). After two (2) minutes, unit will reset on

its own and red LED will flash every 30 seconds until rearmed using the

key. Turn key counter-clockwise to deactivate alarm. Turn key clockwise

to rearm alarm (Figure15).

c Low Battery Alert

Horn chirps intermittently to indicate low battery condition.

Replace 9-volt alkaline battery (Figure16).

Figure14

Figure15

Figure16

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

8 Optional Features

Once power is connected, turn key clockwise to activate alarm. A time delay of 7, 10, 15 or 20 seconds

initiates prior to rail going into an armed state. This allows individualized alarm setting. LED will flash

yellow during this time.

Horn will chirp one (1) time. LED will flash green and repeat every 30 seconds to indicate unit is armed.

Once armed, depress push bar to sound alarm. Rail alarm will sound until disarmed using one (1) of the

following methods:

1. Rail cylinder key

2. Automatic reset (after optional field settable time delay of 2, 5 or 10 minutes)

LED will flash red every 30 seconds to indicate rail has been violated and will continue to flash red until

unit is reset manually. If battery powered and low battery voltage is detected, horn chirps quickly and

repeats every 10 seconds until battery is replaced.

These field selectable switches can change the following functions:

Auto Alarm Reset Request to Exit/Passage Time Delay

DS3 DS4 Timer Reset DS1 DS2 Timer Reset

Off Off 2 minutes Off Off 7 seconds

Off On 5 minutes Off On 10 seconds

On Off 10 minutes On Off 15 seconds

On On Continuous On On 20 seconds

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

Page intentionally left blank.

A8265A 08/19

AL-500 Series

Installation Instructions

Alarmed Exit Devices

1-800-327-8539 • www.arrowlock.com

Reproduction in whole or in partwithout the express written permission of ASSA ABLOY Access and

Egress Hardware Group, Inc. is prohibited.

Page intentionally left blank.

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Aperio KS100 Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron Shear Aligning Magnalock SAM... Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent L980S Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Bedienungsanleitung

Assa Abloy

Assa Abloy EMTEK A Bedienungsanleitung

Assa Abloy

Assa Abloy IKON eCLIQ N111 BA3 Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 309N Installationsanleitung

Assa Abloy

Assa Abloy sFlipLock check 14471 Bedienungsanleitung

Assa Abloy

Assa Abloy LOCWOOD 001TOUCH Bedienungsanleitung

Assa Abloy

Assa Abloy INTERLOCK P84166 Bedienungsanleitung

Assa Abloy

Assa Abloy Bolt ASSA 560/13 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC216 Technische Daten

Assa Abloy

Assa Abloy 421-30-10 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1655 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living B1L Z-Wave Technische Daten

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy Abloy EL590 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent IN100 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy HES 5000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy LOCKWOOD Sliding Door Latch Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale inTouch Technische Daten

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung