Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Installation Instructions

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

FM351 08/19

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

BLSS Trim

For Mortise Locks

ML2000 Series

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

TOC Table of Contents

1 Tools Required ..................................................................2

2 Package Contents ...............................................................3

3 Mortise Lock Handing Instructions...............................................3

4 Door Preparation................................................................4

5 BLSS Trim Installation............................................................6

6 Installation ......................................................................7

a Install Adapter Clutch............................................................7

b Install Outside Lever Assembly...................................................7

c Install Outside Trim ..............................................................8

d Install Inside Adapter Plate Assembly ............................................8

e Install Lock Front ................................................................9

f Install Turn-Piece ................................................................9

g Install Coin-Turn ............................................................... 10

Attention Installer

Please read these instructions carefully to prevent missing important steps.

Notes:

• Improper installation may result in damage to lock and void factory warranty.

• Other product brand names may be trademarks or registered trademarks of their respective owners

and are mentioned for reference only.

1 Tools Required

• Phillips Screwdriver (# 2)

• Torx Tamper Resistant Driver (T-20)

• Torx Tamper Resistant Driver (T-10)

• Hex Key Driver 5/64"

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

2 Package Contents

Figure1

Adapter Plate Pack

858F628

Outside Lever Assembly

858F617-32D

Rose Assembly

858F087-32D

Inside Lever Assembly

858F607-32D

3 Mortise Lock Handing Instructions

1. Move red locking screw to side of lock body being locked.

2. Push in latch. Depress catch plate with screwdriver. (Figure2)

3. Pull latch out of lock body and turn latch over. (Figure3)

Catch Plate

Figure2

LOCK HANDING IS CRITICAL

TO ENSURE LOCK FUNCTIONS

PROPERLY

RED Locking Screw

Figure3

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Mortise Lock Handing Instructions (cont.)

4. Push in latch while holding screwdriver behind latch tail. (Figure5)

Note:

Ensure that latch is pushed in until catch plate is no longer depressed. (Figure4)

5. Rotate lock front to match bevel of door as shown. (Figure6)

Figure4

Figure5

MAKE SURE CATCH PLATE IS EVEN

WITH TOP SURFACE

GOOD BAD

WARNING: LOCK-IN CAN

OCCUR IF LATCH IS NOT

PROPERLY INSTALLED

4 Door Preparation

Important:

Be sure to hand the lockbody before installing.

1. Insert mortise lock into door and fully

tighten 1" lock mounting combination

screws. (Figure7)

2. Turn-piece functions only:

Insert turn-piece door marker spindle

into lockbody on inside of door.

Note:

Use square side of door marker spindle. (Figure8)

3. Turn-piece functions only:

Slide turn-piece door marker over spindle.

4. Turn-piece functions only:

Mark three holes for turn-piece. (Figure9)

5. Coin-turn functions only:

Insert turn-piece marker spindle into lockbody

on outside of door.

Note:

Use square side of door marker spindle. (Figure8)

Figure6

Figure7

Blade Side

Figure8

Turn-Piece Door

Marker Template

Inside of Door

Figure9

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4 Door Preparation

Important:

Be sure to hand the lockbody before installing.

1. Insert mortise lock into door and fully

tighten 1" lock mounting combination

screws. (Figure7)

2. Turn-piece functions only:

Insert turn-piece door marker spindle

into lockbody on inside of door.

Note:

Use square side of door marker spindle. (Figure8)

3. Turn-piece functions only:

Slide turn-piece door marker over spindle.

4. Turn-piece functions only:

Mark three holes for turn-piece. (Figure9)

5. Coin-turn functions only:

Insert turn-piece marker spindle into lockbody

on outside of door.

Note:

Use square side of door marker spindle. (Figure8)

Figure7

Blade Side

Figure8

Turn-Piece Door

Marker Template

Inside of Door

Figure9

4 Door Preparation (cont.)

6. Coin-turn functions only:

Slide turn-piece door marker template over spindle.

7. Coin-turn functions only:

Mark two holes for coin-turn. (Figure10)

8. Remove lockbody from door.

9. Turn-piece functions only:

Drill one middle hole (.290") and two outer holes (3/8")

halfway through door. (Figure11)

10. Coin-turn functions only:

Drill two holes (1/8") halfway through door. (Figure12)

11.Turn-piece functions only:

Install turn-piece thru-bolt plate using truss head screw.

Leave screw slightly loose. (Figure13)

Note:

The thru-bolt plate is installed inside the door pocket.

12. Insert mortise lockbody into door and loosely tighten

1" lock mounting combination screws.

Note:

Make sure lock is unlocked. (Figure14)

Turn-Piece Door

Marker Template

Outside of Door

Figure10

Ø.290" Ø3/8"

Ø3/8"

Figure11

Ø1/8"

Figure12

Thru-bolt Plate

Figure13 Figure14

Unlocked

Locked

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5 BLSS Trim Installation

1. Install strike using 3/4" strike mounting screws.

Note:

Strike must be oriented with narrower hole on

lower half of strike and strike lip towards pull

side of door. (Figure15)

2. Cylinder functions only:

Slide cylinder(s) through spring and collar,

threading into lockbody until cylinder face

is flush with collar. (Figure16)

Note:

Pull key slightly out of cylinder to help thread

into lockbody.

Note:

Cylinder must be oriented correctly. (Figure17)

Correct Incorrect

Note:

Key and cylinder must

be rotated as shown

Figure17

3. Cylinder functions only:

Tighten cylinder set screw. (Figure18)

4. Fully tighten lock mounting screws.

Figure15

Figure16

Strike Lip

Wider Hole

Narrower Hole

Figure18

Cylinder

Set Screw

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

6 Installation

a Install Adapter Clutch

1. Install adapter clutch into

mortise lock hub. (Figure19)

Note:

Adapter clutch is oriented toward

latchbolt as shown.

b Install Outside Lever Assembly

Figure20

Bushing

(Outside)

Rose/Adapter Plate Assembly

Align rose screw with gap in spring cartridge

Outside Lever Assembly

857F598 Spindle

Apply grease to

these surfaces

1. Use outside bushing and spindle to connect

rose/adapter plate assembly to outside lever

assembly. (Figure20)

2. Insert spindle into bushing; ensure that

spindle is inserted no more than ¾"deep.

3. Use spindle to rotate bushing

clockwise into outside lever hole.

4. Fully tighten bushing, then unthread

bushing just enough to allow spindle to

be inserted into lever, keeping

bushing as tight as possible.

5. Once assembled, spindle orientation

should be as shown. (Figure21)

Note:

Longer spindle used on outside

Figure19

857F658

Adapter Clutch

Hinge Side

Figure21

Note position

and orientation

of spindles.

RH Outside LH Outside

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

6 Installation (cont.)

c Install Outside Trim

Figure22

LHR Outside Shown

Make sure spindle seats into clutch adapter then proceed

to Step 6d in order to retain Outside Trim to door.

d Install Inside Adapter Plate Assembly

1. Install inside adapter plate assembly using two (2) machine screws. (Figure23)

Figure23

814F798

Machine Screws #8-32x5/8

Inside Adapter Plate Assembly

LHR Inside

Shown

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

6 Installation (cont.)

e Install Lock Front

1. Install lock front using two (2) front

screws. (Figure24)

f Install Turn-Piece

1. Install turn-piece loosely using two turn-piece

mounting screws. (Figure25)

Note:

Make sure lock is unlocked and turn-piece is

rotated towards latch.

2. Adjust location of turn-piece on door until

turn-piece rotates easily, then fully tighten

mounting screws. (Figure26)

Unlocked

Locked Figure26

Figure24

Figure25

BLSS Trim

Installation Instructions

ML2000 Series

FM351 08/19

in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

g Install Coin-Turn

1. Install coin-turn using two surface

mount screws. (Figure27)

Figure27

Andere Handbücher für Corbin Russwin BLSS ML2000 Series

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Yale YDM7220 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale SIMPLICITY Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS200-640 Bedienungsanleitung

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL574 Bedienungsanleitung

Assa Abloy

Assa Abloy 840C-50 Bedienungsanleitung

Assa Abloy

Assa Abloy 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent SN Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1655 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON FM9930 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent IN100 Bedienungsanleitung

Assa Abloy

Assa Abloy Arrow AL-500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Zi IKON CLIQ Go Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON MORTISE UNLATCH MUNL-12 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living YRD210-ZW Technische Daten

Assa Abloy

Assa Abloy OneSystem 309N Bedienungsanleitung

Assa Abloy

Assa Abloy 118F A71 Series Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 509N Installationsanleitung

Assa Abloy

Assa Abloy 8037...UL-91E91 Series Bedienungsanleitung

Assa Abloy

Assa Abloy TCWI1-M812 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung