Assa Abloy Securitron CEPT-10-10 Bedienungsanleitung

Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader

Tel 800.624.5625 [email protected]

in door opening solutions

Page 1 Rev. C, 05/11

CONCEALED ELECTRICAL POWER TRANSFER SERIES CEPT

INSTALLATION INSTRUCTIONS

PRODUCT COMPATIBILITY NOTE: The Securitron CEPT will NOT operate properly on

openings with the following door/frame/hinge configurations:

Offset Pivots Pocket Pivots Center Hung Doors

Butt Hinges over 6” Swing Clear Hinges Balanced Doors

Available CEPT Models:

CEPT-10

Traditional Connect

10 Wire (2 + 8)

(2) Wire Nut

+ (8) Crimp

EL-CEPT

ElectroLynx®

(Assa Abloy)

12 Wire (8 + 4)

Connectors: 8 Pin + 4 Pin

CEPT-C5E

CAT 5e

(TIA/EIA-568-B Compatible)

9 Wire (8 + 1)

Connectors: 6 Pin + 4 Pin

DESCRIPTION

The Concealed Electrical Power Transfer CEPT unit is designed to provide a secure multiple wire

power and/or data transfer between a door frame and door. The unit mounts directly between

the frame and door along the hinged edge and is available in three multi-wire configurations.

The CEPT is non-handed, allows mechanical (hinged) movement of the door and is totally

concealed when the door is fully closed. This manual provides the information required to

successfully install a CEPT to a standard hinged door opening.

PN# 500-22115

Page 2 Rev. C, 05/11

Components included with this Product:

Item Description Quantity

A CEPT Assembly 1

B Back Box 2

C Screws, 10-24 x 3/4” Phillips Flat Head Undercut (for metal) 13

D Screws, #10 x 3/4” Phillips Flat Head (for wood) 13

E Strain Relief Bushing 2

F Wire Nut (CEPT-10 Only) 4

G Dolphin™ Connector (CEPT-10 Only) 17

RECOMMENDED TOOLS

Basic for Factory Prepped Door Install: Additional for More Detailed Install:

Hammer

Flat Tip Screwdriver: 1/4”

Phillips Screwdriver: #2

Wire Strippers/Crimpers

Pliers

Center Punch

Drill Motor & Bits

Reciprocating Saw & Blades

Router & Bits

Chisel

Metal File

SPECIFICATIONS

Physical

For proper installation and operation of the CEPT, the thickness of the door should be 1-3/4”

minimum. The door opening limitations listed here apply to a (1-3/4”) door equipped with the

following hinge sizes and configurations.

Door Hinge Configuration: Door Opening Angle Range:

Up to 5” Butt Hinge 0-180°

5-1/2” Butt Hinge 0-130°

6” Butt Hinge 0-110°

D G

PN# 500-22115

Page 3 Rev. C, 05/11

Electrical

The following chart shows the electrical specifications for each CEPT model.

MODEL TYPE WIRE SIZE/QTY CURRENT LIMIT (Per Wire)

18 AWG/2 Max. 5A

CEPT-10 10 Wire (2+8) 22 AWG/8 Max. 1A

EL-CEPT ElectroLynx® (8+4) 22 AWG/12 Max. 1A

24 AWG/8 Max. 1A

CEPT-C5E CAT 5e (8+1) 22 AWG/1 Ground (Max. 1A)

INSTALLATION INSTRUCTIONS

NOTE: The CEPT should always be mounted above the second hinge from the floor.

The CEPT was designed primarily to be installed into a factory prepped door and frame.

However, the unit can be installed into an un-prepped door and frame by following the specific

instructions provided on the product installation diagram. The following exploded illustration

shows the included hardware required to properly install a CEPT to a factory prepped door

opening (CEPT-10 shown).

To install the CEPT to a factory prepped door and frame:

Route/pull utility wires/cable through the prepped holes in door and frame.

Pop out the desired knock-out hole in the back box.

Notes:

1. Back boxes are normally required to meet fire code requirements.

2. The 7/8” diameter knock-out holes in the back boxes are provided for EMT type

electrical conduit fittings.

3. The 5/8” diameter knock-out holes are for use of the provided strain relief bushings.

To install the strain relief bushing, lay the utility cable (not included) into the slotted

opening in the bushing allowing a sufficient wire length (loop) for making connections.

Fold the hinged retainer over the cable, squeeze together using pliers and then insert

through the 5/8” [15.9mm] knock-out in the back box.

(

Pre

)

Door

(

Pre

)

Frame

Back Box

(

)

CEPT

PN# 500-22115

Page 4 Rev. C, 05/11

When required, install the appropriate connectors for ElectroLynx® or CAT 5e (not

included) to the end of your utility cable.

Using a #2 Phillips screwdriver, attach each back box to the door and/or frame using the

10-24 x 3/4” long screws (for metal) or the #10 x 3/4” long screws (for wood). These

screws are to be placed through the center hole in each flange of the back box.

Metal Door Prep. Wood Door Prep.

Make connections to the CEPT by:

oUsing the connectors (EL-CEPT or CEPT-C5E models).

oUsing the provided wire nuts for connection of the two (2) 18 AWG wires - and by

using the Dolphin™ (crimp type) connectors to make the appropriate connections to

the remaining 22 AWG wires (CEPT-10 model).

Using a #2 Phillips screwdriver, assemble each side of the CEPT to the door and frame

using the 10-24 x 3/4” long screws (for metal) or the #10 x 3/4” long screws (for wood).

These screws are to be placed through the four corner holes in the face flange of each of

the CEPT housings and also through the outer (clearance) holes in the back box.

MAGNACARELIFETIME REPLACEMENT WARRANTY

For warranty information visit www.securitron.com/en/site/securitron/About/MagnaCare-Warranty/

Back Box Back Box

CEPT

10-24 X 3

”

CEPT

#10 X 3

”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Sargent 6500 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD426 Bedienungsanleitung

Assa Abloy

Assa Abloy 9800 TCNE1 Series Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 519N Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON 32 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL420 Bedienungsanleitung

Assa Abloy

Assa Abloy MUL-T-LOCK SC110 Bedienungsanleitung

Assa Abloy

Assa Abloy IKON +CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron M680EBD Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT DL Series Bedienungsanleitung

Assa Abloy

Assa Abloy ML53PA Bedienungsanleitung

Assa Abloy

Assa Abloy 3090 Leitfaden

Assa Abloy

Assa Abloy Arrow AL-500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Optimum Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem 309N Installationsanleitung

Assa Abloy

Assa Abloy Sargent PE80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDD424A Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Signature Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron EPT-SC Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy EL595 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin IN100 Series Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS200-640 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung