Assa Abloy Sargent FM6100 Series Bedienungsanleitung

A8058:A

4/16/10

FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com

FM6100 Series Multi-Point Lock

Installation Instructions for

Window Shutter Applications

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Recommended Installation:

Install FM6100 so that the

deadbolt is equidistant

from the top and bottom

of the shutter.

FOR TRAINING PURPOSES ONLY

able of Contents

InstallationofDea boltAssembly .......................................................3

Installation of Bottom Bolt Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 & 4

InstallationofTopPusherAssembly .....................................................4

Aligning assemblies in preparation for rilling an pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 & 6

Applying the Drill Jig for proper rilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Pinning the Ro s to engage the Dea bolt Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installation of Insi e an Outsi e Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installation of Cylin er in Outsi e Trim (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

AssembletheTopLatchtotheFrame ....................................................9

InstallationofDea boltStrike .........................................................10

InstalltheBottomStrike..............................................................10

I portant

This device is intended to be part of an integrated window shutter, frame and hardware assembly UL-approved

for both FEMA 361 and ICC 500 guidelines for inswing window shutters. This instruction sheet will take you

through the following steps for full installation.

FM6100 Series Multi-Point Lock

www.sargentlock.com • A8058:A

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Installation Jig Components Drill Guide for Deadbolt Case

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

• Place the window shutter on a horizontal surface with the

pin lever notch located at the top of the shutter facing up.

• The recommended deadbolt assembly location should be

equidistant from the top and bottom of the shutter.

• Assemble the deadbolt case into the lock pocket

provided in the door. Note the orientation of the lock, the

top of the deadbolt case indicates that this should be

toward the top of the shutter.

• Assemble the lock to the edge of the shutter using

(2) 1/4 – 20 by 1

Flat Head Cap Screws.

Installation of the Deadbolt Asse bly

• Loosen the set screw so that the lifting platform will slide

along the lower rod tubing but not slide on its own when

the rod is held vertically. Be sure that the set screw is

oriented so that it will be accessible through the Lower

Through Bolt Cutout on the top side of the shutter.

• When you insert the assembly into the shutter and

through the nylon guides of the deadbolt case this lifting

pad will be in a position to allow you to make the final

necessary adjustment.

Note the orientation of the bottom bolt assembly the

double screw head side (not shown in this image) should

be facing the hinge side of the shutter.

Continue on next page………….

Installation of the Botto Bolt Asse bly

Lower

Through

Bolt Cutout

Set Screw

A8058:A • www.sargentlock.com

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

4www.sargentlock.com • A8058:A

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

• Slide this assembly into the prep. at the top of the shutter,

making sure the plunger pin is oriented with the clearance

slot on the stop side of the shutter.

• Visually align the rod of the Top Pusher Assembly so that it

enters the tube of the Bottom Bolt Assembly that extends

out of the Deadbolt Assembly.

• Align the Top Strike plate to shutter prep. Noting the position

of the beveled edge. It should be on the same side as the

plunger pin.

• Fasten the Top Strike plate and Top Pusher Assembly to the

top of the shutter using (2) #12-24 by 1" Flat Head Cap

Screws.

Installation of the Top Pusher Asse bly

•With the Deadbolt Retracted, slide the Bottom Bolt Sub

Assembly into the prep. hole in the bottom of the shutter. As

you guide the assembly up into the shutter you will need to

guide it into the bottom nylon guide of the Deadbolt Assembly

and then up through the top nylon guide.

• Seat the bottom bolt bracket against the shutters lower

reinforcement plate.

• Align Bottom Bolt Plate to shutter prep.

• Fasten the Bottom Bolt Assembly and Bottom Bolt Plate to

the bottom of the shutter using (2) #12-24 by 1" Flat Head

Cap Screws.

Installation of the Botto Bolt Asse bly continued

Strike Plate note

bevele e ge position

Plunger Pin

Top Pusher Assembly

Nylon Guides

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

A8058:A • www.sargentlock.com

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

• Thread the Top Bolt Clamp into the threaded hole so that

it extends the top latch to the proper position for pinning.

The Top Bolt Clamp will assure that the top latch is in the

correct position for final installation.

• Prepare the lifting platform installation jig by removing the two

wing fasteners and their washers

• Introduce the lifting platform jig up through the under side of

the shutter as shown.

• Using the two wing fasteners and their washers, secure the

lifting platform jig to the shutter.

The lifting platform jig will now be in position to allow sliding the

lifting platform (shown in step 2) so that it rests against the shelf

of the jig.

Continued on next page………….

Align ent of co ponents in preparation for drilling and pinning

Top Bolt Clamp

Lifting platform jig

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

6www.sargentlock.com • A8058:A

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Before continuing to the next step be certain the top pusher

and bottom bolt are in the correct position.

• Bottom Bolt should be flush to the bottom of

the shutter.

• The lifting platform (item 1) should be moved down the bottom

rod and placed against the shelf of the lifting platform jig.

• Next secure the platforms position by tightening the cone

point set screw (item 2). This will assure the point on the set

screw embeds itself firmly into the bottom rod.

Align ent of co ponents in preparation for drilling and pinning continued

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

A8058:A • www.sargentlock.com

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

• Manually project the deadbolt by applying force to the

deadbolt lever toward the bottom of the shutter.

• The deadbolt lever is now in a position to allow the Drill Guide

to be positioned above the deadbolt and fixed into position

using the two drill guide positioning holes provided in both

sides of the deadbolt case.

• The Drill Guide is an alligator type jig. Loosen the Drill Guides

clamping screw, allowing the jaws to rotate 90 degrees to

allow the guide to be positioned above the deadbolt and

closed around the shutter so that the pins on both sides of

the Drill Guide engage the two Drill Guide Positioning Holes.

• nce the Drill Guide is engaged in the positioning holes,

tighten the Drill Guides clamping screw so that it will firmly

secure the jig around the shutter.

• Using the Drill Guide Hole, drill a 1/8" hole (drill provided

with Jig Components) through both sets of rods.

Applying the drill jig for proper drilling

Dea bolt

Lever

Drill Gui e

Positioning

Holes

Drill Gui e

clamping screw Drill Gui e

Positioning

Pins

Drill Gui e

Hole

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

8www.sargentlock.com • A8058:A

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

• Loosen the Drill Guides clamping screw allowing the Drill

Guide to be removed from the shutter.

•Manually retract the Deadbolt by applying force to the

deadbolt lever toward the top of the shutter.

• This will put the pinning hole in the proper position for

fastening the Drive Pin.

• Insert the Drive Pin from the underside of the shutter and

through the holes in the rods and fasten the Drive Pin in

place with the spring washer.

he Lifting Platform Jig and the op Clamp can now be

removed from the shutter.

Pinning the Rods to engage the Deadbolt Lever

• Install the outside trim by inserting it from underneath

the shutter (outside face).

• As it enters the shutter cavity the lifting pad in the

escutcheon will rest on the underside of the lifting pad

secured to the rods in step 4.

• Press the outside escutcheon against the shutter

surface.

• Install the inside trim by placing it over the shutter

prep. and positioning the lifting pad of the inside trim

on the underside of the lifting pad.

• Visually align the mounting holes of the inside

escutcheon to the mounting posts from the outside

escutcheon.

• Insert 4 mounting screws #12 – 24 by 1 ½" and

tighten screws.

Installation of Inside and Outside Tri

Hole shown in proper

pinning position.

Inside Surface

of Door

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

A8058:A • www.sargentlock.com

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

• Insert the Cylinder into the Cylinder Collar

• Place the Cylinder Retaining Nut against the backplate of the outside trim assembly.

• Feed the cylinder and cylinder collar into the cylinder hole of the escutcheon and screw the

cylinder retaining nut to the cylinder until it is fully seated with the cam straight up as shown.

• Secure the cylinder to the escutcheon by tightening the cylinder retaining nut.

Installation of Cylinder in Outside Tri (Optional)

• Insert the top latch into the top of the frame using

(4) ¼" – 20 by 1" Flat Head Screws. The angled

surface should face the shutter.

Asse ble the Top Latch to the Fra e

Cylin er

Collar

Cylin er Retaining Nut

Backplate

Outsi e Trim

Assembly

(4) Flat Hea Screws

FOR TRAINING PURPOSES ONLY

FM6100 Series Multi-Point Lock

10 www.sargentlock.com • A8058:A

Reproduction in who e or in part without the express written permission of Sargent Manufacturing Company is prohibited.

• Assemble the Deadbolt Strike to the frame using

(2) ¼" – 20 by 1" Flat Head Cap Screws.

Installation of Deadbolt Strike

• Place the Bottom Strike into the Strike Shim and

fasten to the frame using (2) ¼" – 20 Screws.

Install the Botto Strike

Deadbolt Strike

Bottom Strike

Strike Shim

Install the Shutter into the frame assembly and shim for proper shutter

gap and for the shutter being square and plumb

END OF INS ALLA ION INS RUC IONS

FOR TRAINING PURPOSES ONLY

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy effeff ePED 1386S00 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT DL Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Passport 1000 PG Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL420 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC216 Technische Daten

Assa Abloy

Assa Abloy hes RF0010 Betriebsanleitung

Assa Abloy

Assa Abloy Yale Real Living YRD210-ZW Technische Daten

Assa Abloy

Assa Abloy sFlipLock check 14471 Bedienungsanleitung

Assa Abloy

Assa Abloy YRD256 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Smart Latch Bedienungsanleitung

Assa Abloy

Assa Abloy 3090 Leitfaden

Assa Abloy

Assa Abloy IKON eCLIQ N110 Bedienungsanleitung

Assa Abloy

Assa Abloy EMTEK EMPowered Motorized Smart Lock Upgrade... Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Smart Latch Bedienungsanleitung

Assa Abloy

Assa Abloy APERIO P100 Handbuch

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy Sargent L980S Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 ML20600 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lever YRL216 Montageanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FM7300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YM Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin IN120 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung