Assa Abloy Sargent 8200 Series Bedienungsanleitung

A8260C 03/20

Installation Instructions

1-800-727-5477 • www.sargentlock.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

7800 and 8200

Series Mortise Lock

Used with VN1 Escutcheon Trim and

V Series Indicators

7800 and 8200 Series Mortise Locks

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

A8260C 03/20

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

1 Tools Required

#2 & #3 Phillips

head screwdrivers

Flat blade

screwdriver

1/8”Allen Wrench 3/8"Drill bit T-20 Torx Screw with

Tamper Pin Driver

TOC Table of Contents

1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2 Indicator Variants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3 Lock set configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

4 Rehanding Indicator (if required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

a Prepare Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

b Install Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

c Install Outside Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

d Install Inside Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

e Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

f Install Outside Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

g Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

6 Indicator Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

7800 and 8200 Series Mortise Locks

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

A8260C 03/20

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2 Indicator Variants

Depending on function and option ordered,

indicators are provided in the following variations,

these instructions detail how to install with

cylinder, however other variations follow similar

instructions. (Figure1)

• Contact factory with questions.

Coin Turn - For

installation on

outside of door.

Cylinder - For

installation on

inside or outside

of door.

No input / blank

-For installation

on inside or

outside of door.

Thumbturn - For

installation on

inside of door.

Figure1

3 Lock set configuration

To set function of multi-function lock or to re-hand, see instructions on lock body.

4 Rehanding Indicator (if required)

Verify hand and bevel of door. (Figure2)

Left Hand

Hinges Left

Open Inward

Right Hand

Hinges Right

Open Inward

LHRB

Left Hand

Reverse Bevel

Hinges Left

Open Outward

RHRB

Right Hand

Reverse Bevel

Hinges Right

Open Outward

Figure2

Note:

Stand outside of locked door when determining door hand.

Next, verify inside and/or outside indicators are handed

correctly, using Spindle Cam Position chart. (Figure3)

If they are handed correctly, skip to Step 5 "Prepare Door".

If they are not handed correctly:

1. Remove indicator back plate by pulling out from top slot,

then remove spindle cam from assembly. (Figure4)

2. Position spindle cam in correct direction for door

hand. (Figure3)

Important:

• For thumbturn indicators, make sure thumbturn is

positioned in 12 o’clock direction as shown. (Figure5)

3. Slide spindle cam post into the correct slot of the

display slide. (Figure4)

4. Re-seat back plate into original position.

5. Return indicator to vacant/unlocked position for installation.

Door Hand: RH / RHRB

Door Hand: LH / LHRB

Outside Indicator

Inside Indicator

Outside Indicator

Spindle Cam Position for Locks with Deadbolt (*and 56 function)

Door Hand: RH / RHRB

Door Hand: LH / LHRB

Outside Indicator

Inside Indicator

Outside Indicator

Spindle Cam Position for Locks without Deadbolt (*except 56 function)

Figure3

Figure4

Spindle

cam

Display

slide slot

Plate slot

for removal

Back plate

Thumbturn

position

Figure5

7800 and 8200 Series Mortise Locks

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

A8260C 03/20

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

5 Installation

a Prepare Door

Prepare door for function holes, size, and location according to A8258

door marker template, if not already prepped.

b Install Lock

1. Verify strike location according to template. Clean out door pocket

and door edge of debris.

2. Ensure handing of lock and door match. Slide lock into door. (Figure6)

3. Temporarily hand tighten two (2) lock screws (#12 x 1-1/4"

wood screws, or #12-24x 1/2"machine screws).

Note:

Keep door open until installation is complete.

c Install Outside Trim

1. Verify lock is in unlocked state (control hub slot should be vertical).

Also, verify indicator is in vacant/unlocked position.

2. Align trim posts with diagonal holes in door, be sure lever is horizontal. Slide outside escutcheon

assembly through lock body from outside door face. (Figure7)

Note:

If indicator is used on outside, align indicator spindle with control hub.

d Install Inside Trim

1. Slide spindle into lockbody hub. (Figure8)

2. Slide adapter and plate assembly over spindle.

3. Secure with two (2) #8-32 x 5/8" screws.

4. For Studio Collection levers only, use trim bushing over adapter plate.

5. Verify lock is in unlocked state (turn outside lever to ensure).

Also, Verify indicator is in vacant/unlocked position.

6. Align escutcheon over adapter and install inside

escutcheon assembly onto inside door face.

Notes:

• If indicator is used on inside, align indicator

spindle with control hub.

7. Through-bolt inside escutcheon to outside

escutcheon with two (2) #8-32 x 2-1/4"screws.

8. Install inside lever on adapter plate.

Secure with set screw.

Note:

Screw heads should be visible on inside escutcheon.

Inside of door

Lock

Screws

Outside

of door

RH door

shown

Figure6

Outside Escutcheon Assembly

Figure7

Figure8

Inside

Escutcheon

Assembly

Studio

Collection

Trim

Bushing

Adapter Plate

Spindle

Lever

Set

screw

#8-32 x 2-1/4" screw

#8-32 x

2-1/4"

screw

#8-32 x

5/8" screws

7800 and 8200 Series Mortise Locks

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

A8260C 03/20

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

5 Installation (cont.)

e Install Cylinder

1. Thread cylinder into lock until flush with escutcheon

surface. (Figure9)

• Pull key slightly out of cylinder to help thread into

lock body.

2. Tighten cylinder clamp screw with #1 Phillips screwdriver.

• Check operation and adjust cylinder if necessary.

Notes:

• SARGENT logo must be horizontal and on top. (Figure10)

• If double cylinder function is used, repeat steps 1 and 2

for second cylinder.

• Removable Core or Interchangeable Core cylinders require

a control key (key stamped with C) to remove and install

the core. This is not provided standard; it must be

requested separately. If requesting 1-bitted control key,

specify 113511 cut.

f Install Outside Front

1. Tighten the two (2) lock screws completely. (Figure11)

2. Attach outside front with two (2) flat head screws

#8-32 x 1/4".

g Perform Functional Check

DO NOT FORCE if resistance is encountered during functional check.

Refer back to Rehanding Indicator (if required) section to ensure

correct handing. Rehand if necessary.

1. Insert key into cylinder (if present) and rotate:

• Ensure there is no friction against lock case or

any other obstructions.

2. Check key retracts latch:

• Key should rotate freely.

3. Throw deadbolt (if present):

• Check key retracts both deadbolt and latch.

4. Test levers:

• Confirm latch and deadbolt (if installed) retract.

5. Verify indicator displays correct status when locked

and unlocked.

Cylinder

Clamp

Screw

Figure9

Incorrect

Key and cylinder must be rotated as shown.

Correct

Figure10

Figure11

Lock

screw

Outside

front

Lock screw

#8-32 x

1/4" screws

7800 and 8200 Series Mortise Locks

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

A8260C 03/20

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

6 Indicator Parts List

Figure12

Figure12 Description Part Number Req.

1 VN1 Indicator Escutcheon Consult Factory 1

2 Indicator Window 81-0811 1

Indicator Display Assembly - Green Unlocked / Red Locked 82-5602

Indicator Display Assembly - Green Vacant / Red Occupied 82-5603

Indicator Display Assembly - Green Unlocked Icon / Red Locked Icon 82-5604

Indicator Display Assembly - White Unlocked / Red Locked 82-5605

Indicator Display Assembly - White Vacant / Red Occupied 82-5606

Indicator Display Assembly - White Unlocked Icon / Red Locked Icon 82-5607

4A Indicator Spindle Cam - Thumbturn / Coin Turn 81-0745 1

4B Indicator Spindle Cam - Cylinder / No Input / Blank 81-0756* 1

4C Indicator Spindle Cam - 05, 37, 38, 59 Functions 81-5577* 1

5 Indicator Backing Plate 81-0748 1

6 VN1 Escutcheon Screw Pack (Not shown) 82-5587 x finish* 1

7 Door Marker Template (Not shown) A8258 1

* These parts are for 1-3/4"standard thickness doors. For other thicknesses, please contact factory.

Note:

Reference 8200 Series parts manual for all lock body parts.

7800 and 8200 Series Mortise Locks

Installation Instructions

Used with VN1 Escutcheon Trim and V Series Indicators

A8260C 03/20

or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

A8260C 03/20

Founded in the early 1800s, SARGENT®is a market leader in locksets, cylinders, door closers, exit devices, electro-

mechanical products and access control systems for new construction, renovation, and replacement applications.

The company’s customer base includes commercial construction, institutional, and industrial markets.

SARGENT is a brand associated with ASSA ABLOY High Security Group, Inc., an ASSA ABLOY Access and Egress

rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

SARGENT Manufacturing Company

100 Sargent Drive

New Haven, CT 06511 USA

800-727-5477

www.sargentlock.com

Andere Handbücher für Sargent 8200 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Effeff 809M Bedienungsanleitung

Assa Abloy

Assa Abloy IKON +CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Assa compact 3000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD226 Technische Daten

Assa Abloy

Assa Abloy Code Handle Window Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent KP Series Installationshandbuch

Assa Abloy

Assa Abloy ASSA Coded 1.2 Installationshandbuch

Assa Abloy

Assa Abloy YALE 4600CK Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDM7116A Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT DL Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff EX118R Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 6500 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1655 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Y-LL67AP Bedienungsanleitung

Assa Abloy

Assa Abloy Interlock IEGL Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Passport 1000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Passport 1000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy PULSE PK200 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff EX118R Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL420 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung