Assa Abloy HES Aperio K100 Handbuch

HES®K100 Aperio®

Wireless Cabinet Lock

Installation & Operating Instructions

Product Contents

A Reader

B Lock Body

C Mechanical Key Override

D Installation Template

E Double Door Bracket

F Strike Plate

G Threadlock Pillow pack

H 2X AA Lithium Batteries*

*AA Lithium Batteries required. Use of other

types of batteries, such as Alkaline, will

significantly decrease battery life.

Diagram 1: Product Components

I: Hardware

IHardware:

a. 2-56 X 7/16" 2x

b. 8-32 X 5/16"

c. 6-32 X 5/16" 3x

d. 6 X 1/2" 6x

e. 8-32" X 2-3/4" 2x

f. 8-32" X 1-3/4" 2x

g. 8-32" X 2-1/2" 2x

h. 8-32" X 3" Rod

i. 8-23 Nut

1 of 12

Orientation A

Orientation B

Orientation C

Lock Orientation Options

Recommended Tools

• Flathead Drivers – 3/32", 3/16"

• Drill & Drill Bits – 1 /16", 3/16", 1 /2"

• Phillips Drivers – PO, P2

• Pencil

• Wire Stripper

• Level

• Square

• Ruler

• Punch

• Scissors

Diagram 2: Orientation Options

2 of 12

Shaft Length

Door Thickness Shaft Used

1/16" – 1/2" L1

> 1/2" – 1-1/2" L2

>1-1/2" – 2-1/4" L3

Hardware Specifications

Micro USB Port

For emergency power & local

(hard wired) firmware updates,

use micro USB port located on

the side of the K100 reader.

Mounting Screw Length for Various Door Thickness

Door Thickness Reader Mounting Cut to Approximate

Screw Length Lock Mounting Cut to Approximate

Screw Length

1/16" Coupling Nut & 3" Rod 10/16" 8-32 X 1-3/4" Break Away 1-1/16"

1/4" Coupling Nut & 3" Rod 13/16" 8-32 X 1-3/4" Break Away 1-1/4"

1/2" Coupling Nut & 3" Rod 1-1/16" 8-32 X 1-3/4" Break Away 1-7/16"

3/4" Coupling Nut & 3" Rod 1-5/16" 8-32 X 1-3/4" Break Away No Cut

1" Coupling Nut & 3" Rod 1-9/16" 8-32 X 2-1/2" 2"

1-1/4" Coupling Nut & 3" Rod 1-13/16" 8-32 X 2-1/2" No Cut

1-1/2" Coupling Nut & 3" Rod 2-1/16" 8-32 X 2-3/4" No Cut

Product Specifications

• Wireless Frequency

2.4GHz, IEEE 802.15.4, using

AES 128-bit encryption

• Lock Battery Type AA Lithium, 1.5 Volts (V)

• Battery Life 50,000 cycles*

*All battery life claims are approximate and based

on a set configuration profile. Battery performance

is based on pre-defined system settings such

as battery chemistry and battery model used,

credential presentation settings (LED/buzzer),

UHF polling period, UHF status intervals, and

operations per day. Actual battery performance

will vary and depends on the factors above.

• Holding Force 400 lbs

• Operating Temperature

32° to 122° F (0° to 50° C)

• HID®multiCLASS SE®technology

Credentials Supported:

• High Frequency (13.56 MHz):

»HID iCLASS®

»HID iCLASS SE®(SIO-enabled)

»HID iCLASS®Seos™

»HID MIFARE®SE

»HID DESfire®EV1 SE

»MIFARE CLASSIC

»DESfire®EV1

• Low Frequency (125 kHz):

»HID Prox®, AWID, EM4102, ioProx

• NFC/BLE*

»Mobile – enabled credentials

*Supported on BLE-enabled models

3 of 12

Prepping

the Cabinet/

Drawer Face

1. Separate Strike Plate Template.

2. ESTABLISH CENTERLINE (for

double door cabinet see Double

Door Prepping, next page).

3. MEASURE cabinet wall thickness

and mark offset line on face of

cabinet/drawer. The offset line

should match with the interior

edge of the cabinet wall.

4. CONTINUE CENTERLINE to

the face of cabinet/drawer.

5. ALIGN template to offset

line and centerline. Remove

backing an apply template

onto cabinet/drawer face.

6. Use punch to mark drilling

locations, then drill mounting

holes. If using mechanical

Key override, drill key

override hole as well.

Diagram 3: Installation Template

Strike Plate

Template

Diagram 4: Prepping

CTR Line

Offset Line

4 of 12

Double Door

Prepping

1. Establish centerline on

inside of stationary door.

2. Continue centerline onto

outside face of cabinet.

3. Align offset line on template

to the edge of the stationary

door and align centerline above.

Remove backing and apply

template to cabinet face.

4. Use punch to mark drilling

locations, then drill mounting

holes. If using mechanical

Key override, drill key

override hole as well.

Diagram 5: Double Door Prep

CTR Line

Offset Line

& edge of

stationary

door

5 of 12

Installing Batteries

1. Install AA lithium batteries

in appropriate position.

2. Install cover and secure

using 2x Screw A.

Reader Installation

1. ALIGN reader with mounting holes and

pull cable through as shown. Trim the

threaded rod to length as outlined in

Mounting Screw Length table on page 3.

2. ADD Threadlock to threaded rod.

Secure Reader to cabinet/drawer

using the cut threaded rod and

coupling nut. DO NOT over tighten.

Diagram 6: Reader Installation

Diagram 7: Installing Batteries

6 of 12

Lock Body

Installation

1. INSERT reader cable through

hole in back of lock body.

2. ALIGN lock body to mounting

holes and secure to cabinet/

drawer face using 2x screw

fand 2x screw d. DO NOT

over tighten. If required use

Screw eor g, instead of f.

3. PLUG cable into slot on lock body.

4. Tuck excess cable into lock body

cavity as shown in Diagram 9.

5. For cabinet/drawer face thicker

than 1/2", add a third Screw d

as shown in Diagram 10.

Diagram 8: Step 1 & 2

Diagram 9: Step 3 & 4

Diagram 10: Step 5

7 of 12

Mechanical

Override

1. SLIDE Override into slot as

shown in Diagram 11.

2. ENSURE that override retracts

latch bolt before installation.

Override should rest loosely

until lock body and battery

cover are installed.

Mechanical Key

Override

Mechanical key override

cam lock sold separately.

1. INSERT CAM LOCK through the

outside of the cabinet/drawer

face and secure with locking nut.

2. INSERT the end of Cam into the

mechanical override and secure

with nut as shown in Diagram12.

OPTIONAL

IMPORTANT NOTE

Reader MUST be programmed before

installing the strike plate. If the cabinet is

closed before the reader in programmed

and after the strike plate is installed,

you will be locked out of the cabinet.

Diagram12: Mechanical Key Override

Diagram 11: Mechanical Override

8 of 12

Strike Plate

Installation

1. ALIGN strike plate template

to centerline and edge of

cabinet. Drill mounting holes.

2. SECURE strike plate to inside

cabinet wall using 2x Screw d,

BUT DO NOT FULLY TIGHTEN.

Adjust strike plate so the

edge is flush with the cabinet

wall edge then tighten.

3. After the strike plate is in

the desired position, fasten

Screw d into strike plate as

shown in Diagram 15.

Double Door

Strike Plate

Installation

1. ALIGN double door bracket

with mounting holes from

the strike plate template.

2. Secure strike plate to the double

door bracket using 3x Screw d

as shown in Diagram 16.

Diagram13: Strike Plate Template Use

Diagram16: Double Door Strike Plate Installation

Diagram14: Strike Plate Installation Diagram15: Step 3

9 of 12

LED Codes

Aperio LED LOCK Codes

(1) ONE Yellow Flash Card read

(1) ONE Green Flash Access Granted

(5) FIVE Yellow (1) ONE Red Force Closed

(in open mode)

Continuous Yellow Flashes

(.25 sec every second) Comhub busy

(1) ONE Red Flash Access Denied

(AC Online)

(3) THREE Red Flash Access Denied

(AC Of f line)

Continuous Red Flashes

(.125 sec every second) Lock is Blocked

(when closing)

(10) TEN Red Flashes Error in Lock

Continuous Yellow Flashes

(.25 sec every 5 seconds) Low Battery

Continuous Red Flashes

(.25 sec every 5 seconds) Dead Battery

Aperio LED HUB Codes

Steady Green Online

Steady Green

+ (1) ONE

Red Flash

Lock Offline

Steady Green

+ (2) TWO

Red Flashes

Access Control

Offline

Steady Green

+ (3) Three

Red Flashes

Access Control

& Lock Offline

Flashing

Yellow UHF

Communication

Aperio Hub Specifications

• Approvals CE, ETL, FCC, IC, C-Tick

• Safety & Emissions

FCC 47CFR Part 15 subpart B and subpart C;

IC RSS-210 EN ETSI 301 489-17 v2.1.1; ENETSI

300 328 v1.7.1; EN 60950-1 ed.2 2007

• Dimensions 82mm x 82mm x 37mm

• Power Supply 8-24 VDC

• Current 250 mA minimum

• Internal Antenna 2 cross polarized dipoles

• External Antenna (Part No. EXT-10-ANT)

One reverse polarity SMA external antenna

connector. Optional antenna type dipole

with max antenna gain of 3.9dBi

• Radio Standard IEEE 802.15.4(2.4GHz)

– 15 channels (11-25)

• Encryption (RadioCommunications)

AES 128 bits

• Wireless Operating Range Up to 50 ft

• Receiver Sensitivity

-100dBm 20% PER

• Wireless Transmit Power 10 d Bm/MHz

• Class of Protection IP 20

• Operating temperature

41°F to 95°F [5°C to 35°C]

• Humidity < 95% non-condensing

• Status LED (red/green/yellow)

10 of 12

Inhaltsverzeichnis

Andere Assa Abloy Sperren Handbücher

Assa Abloy

Assa Abloy Yale Real Living Assure Lock SL Series Technische Daten

Assa Abloy

Assa Abloy effeff EX118R Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS200-640 Bedienungsanleitung

Assa Abloy

Assa Abloy FAB INTERLOCK Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Bedienungsanleitung

Assa Abloy

Assa Abloy Whitco Cyl4 Window Bolt Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron M680EBD Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON CEPT-10 Bedienungsanleitung

Assa Abloy

Assa Abloy Door Lock Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT DL Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy hes RF0010 Betriebsanleitung

Assa Abloy

Assa Abloy Sargent L980S Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 115 Hospital Latch Bedienungsanleitung

Assa Abloy

Assa Abloy KESO KEK i-handle S Benutzerhandbuch

Assa Abloy

Assa Abloy 8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 8037...UL-91E91 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron CEPT-10-10 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PASSPORT 1000 P1 Bedienungsanleitung

Assa Abloy

Assa Abloy 421-30-10 Bedienungsanleitung

Assa Abloy

Assa Abloy 840C-50 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 ML20600 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Profile v.S1 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung