ATD Tools ATD-7343 Bedienungsanleitung

ATD-7343

3 TON LOW PROFILE ALUMINUM FLOOR JACK

OWNER’S MANUAL

Specifications:

This hydraulic jack conforms to all “ANSI / ASME” safety standards.

Visit us at www.atdtools.com

WARNING: This product may contain chemicals, including lead, known to the State of California

to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

Capacity

3 Tons 3-7/8” 18” 47-5/8” 26.3/8” Lx 13” W x 7-7/8 4-1/2” 6 55 lbs.

Overall Size Strokes to Max. Height Weight

Min.

Height Max.

Height Handle

Length Saddle

Diameter

ATD7343_rev_1217

SAFETY WARNING AND PRECAUTIONS

General Safety Warnings:

WARNING: The instruĐƟons and warnings contained in this manual should be read and understood before using

or operaƟng this tool. Do not allow anyone to use or operate this tool unƟl they have read this manual and have

developed a thorough understanding of how this tool works. Failure to observe any of the following instruĐƟŽŶƐ could

result in severe personal injury to tool user and bystanders, or cause damage to the tool and property. Keep this manual

for future reference.

Note: The warnings and cauƟons discussed in this instruĐƟon manual cannot cover all possible condiƟons and

situaƟons that may occur. It must be understood by the operator that common sense and cauƟon are factors which

cannot be built into this product, but must be supplied by the operator.

WARNING: Use safety equipment. User and bystanders should use safety goggles or safety glasses with side shields

which comply with current naƟonal standards, or when needed, a face shield. Use an ANSI approved dust mask or respirator

when working around metal, wood, and chemical dusts and mists. This applies to all persons in the work area. Also use

non skid safety shoes, hardhat, gloves, dust collecƟon systems, and hearing protecƟon when appropriate.

WARNING: Keep bystanders and children out of the work area while operaƟng this tool.

WARNING: Always keep your work area clean, uncluƩered, and well lit. CluƩered or dark areas invite accidents and

injuries. DO NOT work on Ňoor surfaces that are slippery.

WARNING: Do not operate this tool if you are Ɵred or under the inŇƵence of alcohol, drugs, or medicaƟons that could

aīect your ability to use the tool properly.

WARNING: Dress properly. Do not wear loose clothing or jewelery as they can be caught in moving parts. Wear

restricƟve hair covering to contain long hair.

WARNING: Do not reach over or across running machines. Keep proper fooƟng and balance at all Ɵŵes. Non skid

footwear is recommended when working.

Product ^ƉĞĐŝĮĐ Warnings:

Non compliance with thesewarnings may result in injury or damage to the jack or the vehicle.

WARNING: NEVER use hydraulic jack as a stand alone device. AŌer liŌing, IMMEDIATELY support the liŌed

vehicle with a pair of appropriately rated jack stands. NEVER place ANY poƌƟon of your body beneath the vehicle when

lŝŌing OR lowering.

WARNING: Do not modify the jack in any way.

WARNING: Never exceed the rated capacity of the jack.

WARNING: This jack is a liŌing device only and should never be used to move the vehicle.

WARNING: The jack should be supported on a solid and level ground. Never use the jack in a surface where it may

sink into the ground.

WARNING: Ensure that there are no persons inside the vehicle to be liŌed. Switch oīthe engine and apply the brake.

Chock each unliŌed ƟƌeinBOTHdirecƟons as shown below.

WARNING: PosiƟon the jack under the manufacturer's recommended liŌing point for the vehicle. Oīcentered loads

can slip and accidents may result.

WARNING: During raising and lowering of the load, precauƟons should be taken to avoid movement of the vehicle.

WARNING: Traĸc may cause the raised vehicle to rock during roadside use of the jack.

WARNING: Never work on, under or around a raised vehicle supported only by a hydraulic jack. Always use

adequately rated jack stands.

WARNING: Never posiƟon any part of your body near the movable parts of the jack.

WARNING: Ensure that there are no persons, tools or obstrucƟons underneath the vehicle prior to lowering.

WARNING: Do not adjust the overload bypass valve under any circumstance.

PRIOR TO OPERATION:

Air may become trapped in the hydraulic system during transit.

To Purge Air

1. Insertthehandleintothesocketandsecureitwiththesetscrewprovided.

2. Turn the handle counterclockwise unƟl release valve is open; pump the jack several Ɵmes to purge the accumulated

air in the system.

3. Turn the handle clockwise to close the releasevalve. The jack is now ready to use.

OPERATING INSTRUCTIONS:

To Lift a Vehicle:

Turn the handle clockwise. Move the handle up and down. Use the full stroke of the piston for greater speed.

Support the vehicle with appropriate jack stands.

LiŌthe vehicle to remove the jack stands, ensuring that there are no persons or obstrucƟons under the vehicle.

Turn the handle counter clockwise.

MAINTENANCE:

Important: Both the maintenance and repair of the jack may only be performed by qualiĮed persons, who have suĸcient

knowledge of the hydraulic system used in these jacks

Regularly lubricate the moving parts in the wheels, arms, handle and pump roller pin.

Only original replacement parts should be used.

EXTREMELY IMPORTANT: NEVER use brake ŇƵŝd OR transmission Ňuid for lubricaƟon, or for Įůůing the

hydraulic system. Use ONLY quality hydraulic jack oil for lubricĂƟon and Įůling of the hydraulic system.

When the jack is not in use, make sure the liŌing arm is fully retracted to avoid corrosion.

Replace the hydraulic ŇƵŝd in the reservoir at least once a year. To check the hydraulic ŇƵŝd level, lower the ůŝŌŝŶŐ

arm completely.

The hydraulic ŇƵŝd level should be just below the Įller plug. If the oil is too low, the jack will not raise to its adverƟsed

maximum height. Replenish if necessary, and reinstall the rubber Įller plug. Do not overĮll the jack. Excessive

hydraulic oil may render the jack inoperaƟve.

Inspect the jack before each use. Take correcƟve ĂĐƟon or remove the jack from service if any of the following

problems are found:

A. Cracked or damaged frame

B. Leaking hydraulic ŇƵŝd

C. Scored, damaged piston rod

D. Loose hardware

E. ModiĮed equipment

Keep warning labels and instrucƟonal decals clean and readable. You may use a mild soap soluƟon to wash external surfaces

of the jack.

TROUBLESHOOTING:

CAUTION:To prevent personal injury, all inspec on, maintenance, and repair procedures must be performed when

the jack is free of load.

Trouble Cause Solu on

Jack Does Not Li

1. Release valve is open 1. Verify the release valve is

closed. Release valve may

need cleaning

2. Low/no hydraulic uid in

reservoir 2. Fill with approved hydraulic

uid and bleed system

3. Air trapped in hydraulic

system 3. Follow the purge air

procedure

4. Load is above capacity of jack 4. Use the correct equipment

5. Delivery valve and/or bypass

valve not working correctly 5. Clean to remove dirt or

foreign objects from the

system. Replace hydraulic

uid

6. Seals worn or defec ve 6. Replace seals

Jack li s only ally 1. Too much or not enough

hydraulic uid 1. Check hydraulic uid level

Jack advances slowly 1. Pump not working correctly 1. Rework pump

2. Seals leaking 2. Replace seals/O-rings

Jack li s load, but doesn't

hold

1. Cylinder packing is leaking 1. Replace packing

2. Valve not working correctly.

(Suc on, delivery, release or

bypass)

2. Inspect valves. Replace if

necessary

3. Air trapped in hydraulic

system 3. Follow the purge air

procedure

Jack leaks hydraulic uid 1. Worn or damaged seals 1. Replace seals

Jack will not retract

1. Release valve is closed 1. Open the release valve by

turning the handle

counter-clockwise (CCW).

Maybe necessary to clean

release valve

NOTE: Should you need assistance with parts, service or warranty, please contact your distributor

or point of sale.

ATD-7343

ITEM# ORDERING PART# PART DESCRIPTION ITEM# ORDERING PART# PART DESCRIPTION

1 PRT7343-01 P01 - SADDLE PAD 11 PRT7343-11 P11 - NUT, M12

2 PRT7343-02 P02 - SADDLE SCREW 12 PRT7343-12 P12 - HANDLE YOLK

3 PRT7343-03 P03 - SADDLE 13 PRT7343-13 P13 - HANDLE SETSCREW

4 PRT7343-04 P04 - SADDLE BASE 14 PRT7343-HD HD - COMPLETE HANDLE ASSEMBLY

5 PRT7343-05 P05 -LIFTARM ASSEMBLY 15 PRT7343-HD HD - COMPLETE HANDLE ASSEMBLY

6 PRT7343-06 P06 - RADIUS ROD 16 PRT7343-HD HD - COMPLETE HANDLE ASSEMBLY

7 PRT7343-07 P07 - FRONT WHEEL 17 PRT7343-17 P17 - TIE ROD

8 PRT7343-08 P08 - CARRYING PLATE 18 PRT7343-18 P18 - POWER UNIT ASSEMBLY

9 PRT7343-09 P09 - SIDE PLATE N/S PRT7343-RK PRK -COMPLETE O-RING AND SEAL KIT

10 PRT7343-10 P10 -REAR CASTERASSEMBLY

WARRANTY

1 YEAR LIMITED WARRANTY

THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES

PURCHASED FROM: _______________________________________

DATE PURCHASED: ________________________________________

INVOICE/RECEIPT NUMBER: _________________________________________

Your ATD-7343 is warranted for a period of 12 months from the original purchase date.

For a period of one (1) year from your purchase date, ATD Tools Inc. will repair or replace (at its option) without charge, your

ATD product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced

during normal use of the product. This limited warranty is your exclusive remedy.

To access the benefits of this warranty, contact your supplier, or point of sale directly. You may be advised to return the product

under warranty, freight prepaid, to your supplier for warranty determination.

If this ATD product is altered, abused, misused, modified, or undergoes service by an unauthorized technician, your warranty will

be void. We are not responsible for damage to ornamental designs you place on thisATD product and such ornamentation should

not cover any warnings or instructions or they may void the warranty. This warranty does not cover scratches, superficial dents, and

other abrasions to the paint finish that occur under normal use. It also does not cover normal wear items such as but not limited to

brushes, batteries, drill bits, drill chucks, pads or blades.

Subject to the law in your state:

(1) Your sole and exclusive remedy is repair or replacement of the defective product as described above.

(2) ATD is not liable for any incidental damages, including but not limited to, lost profits and unforeseeable consequences.

(3) The repair and replacement of this product under the express limited warranty described above is your exclusive remedy and is

provided in lieu of all other warranties, express or implied. All other warranties, including implied warranties and warranties of

merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is prohibited, these warranties are limited to

one year from your date of purchase of this product.

Some states’ laws do not allow limited durations on certain implied warranties and some states’ laws do not allow limitations on

incidental or consequential damages. You should consult the law in your state to determine how your rights may vary.

[Affix receipt or invoice here for safe keeping]

Inhaltsverzeichnis

Andere ATD Tools Jack Handbücher

ATD Tools

ATD Tools 7514 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7367W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7462 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7465 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7344B Bedienungsanleitung

ATD Tools

ATD Tools ATD-7317 Service-Handbuch

ATD Tools

ATD Tools 7436A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7345B Bedienungsanleitung

ATD Tools

ATD Tools 7435 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7461 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7383W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7380 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7447 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7387W Bedienungsanleitung

ATD Tools

ATD Tools 7343 Bedienungsanleitung

ATD Tools

ATD Tools ATD-2025 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7435A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7486B Bedienungsanleitung

ATD Tools

ATD Tools SwiftLift ATD-7325 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7328A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7328 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7237 Bedienungsanleitung

ATD Tools

ATD Tools Atd-7430 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7333B Bedienungsanleitung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Bushranger

Bushranger RJX01 Bedienungsanleitung

Clarke

Clarke CTJ2500QLG Installations- und Betriebshandbuch

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung