ATD Tools ATD-7317 Gebrauchsanweisung

7137-DTA:ledoM

noT2:yticapaC

ATD-7317

Low Proﬁle Service Jack

Capacity Min. Height Max Height Handle

Length

Overall

Length

Overall

Width

Saddle

Diameter

Shipping

Weight

2 Ton 2 3/4” 24” 49-1/4” 36” 15-1/8” 4” 106 LB

Contents:

Page: 1. Speciﬁcaons

2. Safety & Warning Informaon

3. & 4. Setup, Operaon & Prevenve Maintenance

5. Inspecon, Storage & Troubleshoong

6. Exploded View & Replaceable Part Numbers

7. Warranty Informaon

8. Prevenve Maintenance Record Log

eran

Instrucons & Parts Manual

7137-DTA:ledoM

noT2:yticapaC

SAFETY & WARNING INFORMATION

IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE

Before operang this device, be sure to read all content within this manual, ensuring that you

understand the operang procedures, maintenance requirements and all safety warnings.

The owner and/or operator shall have an understanding of the product, its operang

characteriscs, and safety operang instrucons before operang this device. Safety informaon

shall be emphasized and understood. If the operator is not ﬂuent in English, the product and

safety instrucons shall be read to and discussed with the operator in the operator’s nave

language by the purchaser/owner or his designee, making sure that the operator comprehends

their contents.

Acons to help prevent dangerous situaons

Study, understand, and follow all instrucons before operang this device.

Do not exceed the rated capacity stated.

Use only on hard level surfaces.

This item is to be used as a liing device only. Immediately aer liing, support the

vehicle with appropriate means.

Do not move or dolly the vehicle while it is on the jack.

Li only on areas of the vehicle as speciﬁed by the vehicle manufacturer.

No alteraons shall be made to this product.

Failure to heed these markings may result in serious personal injury and/or property

damage.

This is the safety noﬁcaon symbol.

This symbol will nofy you of any

potenal injury hazards. Please

follow all instrucons that follow this

symbol to avoid possible injuries or

death.

Indicates a hazardous

situaon. If proper steps are

not followed, death or

serious injury could result.

7137-DTA:ledoM

noT2:yticapaC

SETUP, OPERATION & PREVENTIVE MAINTENANCE

Setup

Prior to each use, visual inspecon (See Pg. 5) shall be made to the device by checking

for abnormal condions, such as cracked welds, leaks, and damaged, loose, or missing

parts.

Consult the vehicle owner’s manual to determine the locaon of li points.

Be sure to set the vehicle in park with the emergency brake on and wheels securely

chocked.

Be sure that the vehicle and the jack are on a hard, level surface.

Assembly

If two piece handles are provided, assemble the upper secon into the lower secon,

line up the holes, insert and ghten the screw.

Insert the boom end of handle into handle fork and securely ghten the bolt and

washer. Ensure the handle can turn freely.

Liing

Turn the handle/release valve clockwise to the closed posion. Do not over ghten.

Posion the jack under the speciﬁed li point.

Begin liing by pumping the handle up and down.

Immediately aer liing, support the vehicle with appropriately rated jack stands.

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack

stands.

Lowering

Turn the handle/release valve clockwise to the closed posion. Do not over ghten.

Pump the handle up and down to livehicle oﬀ jack stands.

Remove the jack stands. Do not get under or let anyone get under the vehicle while

lowering.

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the

ground

7137-DTA:ledoM

noT2:yticapaC

SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)

Maintenance

NOTICE: Use high grade hydraulic oil only. Never use brake ﬂuid, motor oil, transmission ﬂuid,

turbine oil or any other ﬂuids. ISO-VG22 or equivalent hydraulic oil is recommended.

Check and Reﬁll Oil

With the jack in the fully lowered, level posion, if unit cover is provided, remove unit

cover, then remove oil ﬁller plug.

Proper oil level should be just covering inner cylinder as seen from the oil ﬁller plug

hole.

Do not overﬁll. Always ﬁll with new, clean hydraulic jack oil as recommended above.

Reinstall oil ﬁller plug, then reinstall unit cover.

Lubricaon and Cleaning

Periodically clean and lubricate all moving parts and pivot points.

Air Venng Procedures

With the jack in the fully lowered posion, release valve open, remove oil ﬁller plug.

Pump the handle rapidly several mes. Reinstall oil ﬁller plug.

Turn the handle/release valve clockwise to the closed posion.

Pump the handle unl the li arm reaches maximum height and connue to pump

several mes to remove trapped air in the system.

Turn the handle/release valve counterclockwise in one full turn and lower li arm to the

lowest posion. Use force on saddle if necessary.

Carefully and slowly loosen oil ﬁller plug to release pressurized air.

Repeat above steps unl trapped air is completely vented.

Damaged Equipment

Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally

SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary repairs

be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permied by

the manufacturer or supplier.

Alteraons

Because of potenal hazards associated with this type of equipment, no alteraons shall be

made to the product.

Aachments and Adapters

Only aachments and/or adapters supplied by the manufacturer shall be used.

7137-DTA:ledoM

noT2:yticapaC

INSPECTION, STORAGE

TROUBLESHOOTING

Inspecon

Visual inspecon shall be made before each use of the device by checking for abnormal

condions, such as cracked welds, leaks, and damaged, loose, or missing parts.

Other inspecons shall be made per product operang instrucons.

This device shall be inspected immediately if the device is believed to have been

subjected to an abnormal load or shock. It is recommended that this inspecon be made

by a manufacturer’s or supplier’s authorized repair facility.

Owners and/or operators should be aware that repair of this equipment may require

specialized knowledge and facilies. It is recommended that an annual inspecon of the

product be made by a manufacturer’s or supplier’s authorized repair facility and that

any defecve parts, decals, or safety labels or signs be replaced with manufacturers or

supplier’s speciﬁed parts.

Storage

This Jack should be stored in a dry locaon on a level surface.

Troubleshoong

Symptom Possible Causes Soluon

Jack will not li the load. 1. Release valve not ghtly

closed.

2. Low oil level.

3. Defecve or worn internal

parts.

4. Load exceeds maximum

allowance.

1. Tighten release valve.

2. Check and add oil. Follow “Check

and Reﬁll Oil” instrucons on Pg.4.

3. Disconnue use and contact a

local repair center.

4. Use a higher capacity jack.

Jack will not hold the load. 1. Release valve not ghtly

closed.

2. Power unit malfuncon.

1. Tighten release valve.

2. Disconnue use and contact a

local repair center.

Jack will not descend to

minimum height, or will not

remain in lowered posion.

1. Air trapped in system.

2. Reservoir oil overﬁlled.

1. Vent air out of system. Follow

“Air

Venng Procedures” above.

2. Check and ensure proper oil

level. Follow “Check and Reﬁll Oil”

instrucon on Pg.4.

Jack will not li to max

height.

1. Low oil level. 1. Check and ensure proper oil level.

Follow “Check and Reﬁll Oil”

instrucons above.

Jack will not funcon

properly aer tried soluon.

1. Internal malfuncon or

structural damage.

1. Stop usage and contact an

authorized repair center.

7137-DTA:ledoM

noT2:yticapaC

EXPLODED VIEW & REPLACEABLE PART NUMBERS

* Items not idenﬁed by part number are not available for replacement.

Item Part Number* Descripon Qty

1 LYD2G-100 Front wheel assembly 2

2 LYD2K-300 Saddle w/pad 1

3 GB1152-89-M6 Grease Fing 1

4 LYD3J-3 Cover 1

5 LYD3F-600 Handle Assembly w/ foam 1

6 LYD2-9A Return Spring 2

7 LYDBI-2T.3 Power Unit Assembly 1

8 LYD3G-300 Handle Fork Assembly 1

9 LYD3G-400 Rear Caster Assembly 2

10 LYDBI-3T-17 Handle foam only 1

11 LYD2K-3B Saddle pad only 1

N/A LYD3F-100 Oil Filler Screw w/ Seal 1

7137-DTA:ledoM

noT2:yticapaC

WARRANTY INFORMATION

ONE YEAR LIMITED WARRANTY

For a periodof one (1) year from your purchase date, ATD Tools, Inc. will repair or replace (at its

option) withoutcharge, your ATD product ifitwas purchasednew and the producthas failed

due to a defect in material or workmanship which you experienced during normal use of the

product. This limited warranty isyour exclusive remedy.

To access the benefits of this warranty, contact the ATD warranty center at1-844-364-9922 for

confirmationthat this warranty applies. Thereafter, you may be advised to return the product

under warranty, freight prepaid, to the ATD Tools, Inc. service department.

If this ATD product is altered, abused, misused, modified, or undergoes service by an

unauthorized technician, your warranty will be void. We arenot responsible for damage to

ornamental designs youplace on thisATD productand such ornamentation should notcover

any warnings or instructions or they may void the warranty. This warranty does not cover

scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.

Subject to the law in your state:

(1) Your sole and exclusive remedy is repair or replacement of the defectiveproduct as

described above.

(2) ATD Tools, Inc. isnot liable for anyincidental damages, including butnot limited to, lost

profits and unforeseeable consequences.

(3) The repair and replacementof this productunder the express limited warranty described

above is your exclusive remedyand is provided in lieu ofall other warranties, express or

implied.All other warranties,including implied warranties and warranties of

merchantability or fitness for a particular purpose are disclaimed and,ifdisclaimer is

prohibited, these warranties are limited to one year from your date of purchase of this

product.

Some states’ lawsdo notallow limited durations on certain implied warranties and some states’

lawsdo not allow limitationson incidental or consequential damages.You should consult the

law in your state to determine how your rights may vary.

Made in China to ATD Tools, Inc. Speciﬁcaons

Visit us at www.atdtools.com

Warranty Service Number 1-844-364-9922

For Non-warranty issues, please contact your supplier.

Printed In China

7137-DTA:ledoM

noT2:yticapaC

PREVENTIVE MAINTENANCE RECORD LOG

Date Maintenance Performed

Inhaltsverzeichnis

Andere ATD Tools Jack Handbücher

ATD Tools

ATD Tools ATD-7350A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7443A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7435 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7343A Bedienungsanleitung

ATD Tools

ATD Tools 7430A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7423W Bedienungsanleitung

ATD Tools

ATD Tools 7434A Bedienungsanleitung

ATD Tools

ATD Tools ATD-2025 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7384W Bedienungsanleitung

ATD Tools

ATD Tools 7380 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-7367W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7462 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7391A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7404 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7435A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7421W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7381W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7237 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7465 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7438 Bedienungsanleitung

ATD Tools

ATD Tools Atd-7432 Gebrauchsanweisung

ATD Tools

ATD Tools 7436A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7382W Bedienungsanleitung

ATD Tools

ATD Tools ATD-7343 Bedienungsanleitung

Beliebte Jack Handbücher anderer Marken

Omega Lift Equipment

Omega Lift Equipment 18122C Gebrauchsanweisung

Pittsburgh

Pittsburgh 58816 Montageanleitung

Unimec

Unimec TP Bedienungsanleitung

Sonic

Sonic 4800703 Bedienungsanleitung

BGS technic

BGS technic 70039 Bedienungsanleitung

TradeQuip

TradeQuip 1128T Bedienungsanleitung

VEVOR

VEVOR TJD-12000SP-F Bedienungsanleitung

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Bedienungsanleitung

Stels

Stels 51131 Bedienungsanleitung

Bushranger

Bushranger RJX01 Bedienungsanleitung

Clarke

Clarke CTJ2500QLG Installations- und Betriebshandbuch

Valex

Valex 1650520 Bedienungsanleitung

Pfaff

Pfaff Merkur M0 Bedienungsanleitung

Beta

Beta 3050/K Beilage

Sealey

Sealey 1050CXHV Bedienungsanleitung

Jung

Jung JH Series Bedienungsanleitung

URIAH

URIAH UC200020 Bedienungsanleitung

Kennedy

Kennedy KSJ010 Bedienungsanleitung