Atlona AT-COMP-64M Bedienungsanleitung
AtlonA
6x4 Component Matrix Switcher
with Stereo Audio
AT-COMP-64M
User Manual
TABLE OF CONTENTS
1. Introduction .................................................. 1
2. Features .................................................. 1
3. Package Contents .................................................. 1
4. Specications .................................................. 2
5. Panel Descriptions .................................................. 2
5.1 Front Panel .................................................. 2
5.2 Rear Panel .................................................. 3
6. Remote Control .................................................. 4
7.RS232 Serial Interface .................................................. 5
7.1. Connect a PC or Control System .................................................. 5
7.2. RS232 .................................................. 5
7.3. Protocol Commands .................................................. 5
8. RS232 Serial Commands .................................................. 6
8.1. Power Off Mode .................................................. 6
8.2. Front Panel Lock .................................................. 6
8.3. Unit Reset .................................................. 6
9. Typical Application .................................................. 7
10. Installation .................................................. 8
11. Safety Information .................................................. 9
12. Warranty .................................................. 10
13. Atlona Product Registration .................................................. 11
INTRODUCTION
1
Atlona Technologies’ AT-COMP-64M is one of the most innovative Component Matrix switchers
with Stereo Audio on the market. The AT-COMP-64M has 6 individual Component Video (RCA)
inputs with Stereo Audio and 4 individual outputs. Because it is a matrix switch, any input can
routeto any output; and the same input can routeto all outputs or any other combination. Boast-
ing high speed Video Bandwidth of 325MHz, Maximum 380Mhz, this unit is ideal for connecting
sources including: (VCRs, Camcorders, Video Game Consoles, DVDs, Satellite Receivers, Set
Top Boxes, etc.) to desired displays such as: (HDTV, LCDs, Plasma Monitors, Video Projectors,
etc.) Selection of inputs can be achieved manually through the Front Panel, an Infrared Remote
Control unit or RS232 control. Switch with awless and crystal-clear distribution of all High Res.
HDTV video formats up to 1080p as well as audio signals. With these attributes, the AT-COMP-
64M is a great matrix switch capable of handling High Denition Television applications.
• 6 inputs to 4 outputs Component Video (Matrix Switcher)
• Supported Signals:
Component Video: YPBPR
Audio : Stereo Audio (Audio Right/Audio Left)
• Support RS 232 interface
• Control Through IR remote control and Manually via Front Panel Buttons
• Video Bandwidth: 325MB
• Resolutions: 480p, 576p, 720p, 1080i, 1080p
• Included 19 inch Ear mounts
• Power supply DC12Volt, Universal Type Switch 100~230VAC, 50/60Hz
• AT-COMP-64M Matrix Switcher x 1.
• Instruction Manual x 1
• IR Remote Controller
• RS 232 Drive CD x 1
• Universal AC Adaptor : 12V DC
• 19in. Rack Mount ears ( pair ) x 1
FEATURES:
PACKAGE CONTENTS:
SPECIFICATIONS
PANEL DESCRIPTIONS
2
Type of Switcher 6 inputs to 4 outputs, Component Video/Digital Audio Matrix Switch
I/O Signals Component Video (YPBPR) 0.5~1.0Vpp, DDC 5Vpp,
Stereo Audio - 2x RCA connector (Red/white)
Video Bandwidth 325MHz (-3db), 200mVp-p
Video Supported High Resolution formats 480i/p, 720p & 1080i/p
Audio Supported Stereo Audio(Audio Right/Audio Left)
Low all hostile crosstalk -83 db@5MHz
Controls IR remote, Select buttons on the front panel & RS232
PC RS232 Control RS232 interface serial via DRV on a PC
Gain control 60MHz 0.1 db gain atness
Safety Approvals CE, FCC, RoHS(2002/95/EC)
Dimensions (LWH) 19”x 7.87” x 1.73”(482mm x 200mm x 44mm)
Power Supply 12V DC. Use Universal Switch Type 50/60Hz,100~230 VAC
Shipping Weight 4.15 Kgs / 8.58 lb
1. Front Panel
1. POWER SWITCH: The power switch turns the unit ON and OFF. The LED will illuminate red to indi
cate that the switcher is ON
2. OUTPUT STATUS LED DISPLAY. Output channels 1 to 4 show from LED display. This will illuminate
red to indicate that desired video source is present on chosen input.
3. & 4. INPUT SOURCE SELECT BUTTONS. Setup the input sources 1 - 6
5. IR SENSOR. The IR sensor receives IR commands from the supplied remote controller
6. 19 INCH EAR MOUNT PAIR. 19 inch Ear Rack Mount pair
2. Rear Panel
1. DC Power Input. DC power plug-park input connector. Ensure that the plug-park used is of an
approved type and is of sufcient current carrying capacity with the correct voltage and connector
polarity. 12Volt DC power supply 2A Max.
Power Jack:
DC Jack - inner OD O 2.1mm (+ )
Outside OD O 5.5mm (GND)
Power input - 12VDC, 2A
2. RS 232 Connection. RS 232 control is t to allow interfacing to a PC, such as a computer or touch
panel control, to the switcher via DB-9pin Female connector for serial RS-232 control
DB-9pin Female connector
3. INPUTS: 1-6 Component/Stereo Audio. Connect desired source of Component Video(YPBPR)/Stereo
Audio devise to 6x4 switcher.
Inputs 1- 6 port source signals :
Component Video(YPBPR),
3x RCA Connectors,
Stereo Audio,
2x RCA Connectors
4. Outputs:1- 4 Component/Stereo Audio. Connect desired signal of Component Video(YPBPR),
& Audio direct to Female RCA connector. This connector supports component video & audio to HDTV
display device.
Output 1- 4 display port signals :
Component Video(YPBPR),
3x RCA Connectors,
Stereo Audio,
2x RCA Connectors
2 3
Before making any connections to the AT-COMP-64M, observe the following:
Mains voltage supply must match the label on the supplied plug-Pack (+/- 10%)
Power switch is OFF
All system grounds (earth) must be connected to a common point.
Avoid powering equipment within a system from multiple power sources that may be separated by large
distances
Connect all audio video sources and destination equipment
Power up all desired sources and destination and displays
For each destination output select the appropriate input source by using the front panel input 1~4 select
buttons, the supplied IR remote control, or through the RS 232 serial communications port.
Upon power up, the switcher will return to its last used setting before being powered down.
Series Code: 32 CB
1. SWITCH POWER ON or OFF.
Controller with a separate power to turn ON and OFF
2.OUTPUT 1 - 4 : OUTPUT TO TV DISPLAYS.
Output -1 : TV-1 Component Video (YPBPR) HDTV Display
Output -2 : TV-2 Component Video (YPBPR) HDTV Display
Output -3 : TV-3 Component Video (YPBPR) HDTV Display
Output -4 : TV-4 Component Video (YPBPR) HDTV Display
3.INPUT 1 - 6 : INPUT VIDEO SOURCES SELECTION.
Input -1 : AV-1 Component Video (YPBPR) Signal source device
Input -2 : AV-2 Component Video (YPBPR) Signal source device
Input -3 : AV-3 Component Video (YPBPR) Signal source device
Input -4 : AV-4 Component Video (YPBPR) Signal source device
Input -5 : AV-5 Component Video (YPBPR) Signal source device
Input -6 : AV-6 Component Video (YPBPR) Signal source device
4
REMOTE CONTROL
4
1. Connect a PC or Control System
Pin RS-232 Denition
1 - Not used
2 TX Transmitter
3 RX Receiver
4 - Not used
5GND Ground
6 - Not used
7 - Not used
8 - Not used
9 - Not used
2. RS232
Atlona’s AT-COMP-64M can be controlled via the RS-232 serial control port to allow for interfacing to a
PC, or similar third party control system.
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit
When the unit recognizes a complete command it will perform the requested action - there is no delimiter
character required.
The unit does not send out a message when a value is changed from the front panel or by IR control. If the
unit needs to be controlled via the front panel in addition to the RS232 control, you should regularly poll
the unit status to ensure the control system accurately relate the current settings.
3. PROTOCOL COMMANDS
To Switch Inputs to Outputs
SBI0XO0Y - Where X is Output Number (1-4) and Y is Number (1-6)
Unit will respond with
SBUD0XOY - Where X is Output Number (1-4) and Y is Input Number (1-6)
Example : Send Input 6 to Output 4
SBUD06O4 – Send
SBI06O04 – Rcvd
5
RS-232 SERIAL INTERFACE
Note: Turning the unit System Power Off over RS232 will distinguish the LED display leaving only the Power
Switch LED on. The Video and Audio outputs will also mute. While the unit is turned off by RS232 it will
continue to accept and act upon switching commands. For example, if the unit is in the off mode
(via RS232) and you send a command to switch an input to an output, that route will complete and the
video and audio will now appear on that channel only. The front panel LED for that particular output will
also show the input selected (for that single output channel only). The remaining LED’s will remain off
and video and audio outputs muted. The unit will still return to its status and change messages in response
to the commands sent while in Power Off state. A hard reset command (SBALLRST) will return the unit to
normal operation and also unlock the front panel.
1. POWER OFF MODE
SBSYSMOF - Place system into Standby (Soft Power Off)
SBSYSMON - Bring unit out of Standby (Soft Power On)
Unit will respond with
SBALOFAK - Unit is in Standby
SBALONAK - Unit is no longer in Standby
Example : Put Unit in Standby (Soft Power)
SBSYSMOF - Send
SBALOFAK - Rcvd
2. FRONT PANEL LOCK
Note: Hard resetting the unit will unlock the Front Panel controls.
SBSYSMLK - When front panel is locked, changes can only be made by RS232
SBSYSMUK- Front Panel Unlock
Unit will respond with
SBSYSLOK - Front Panel has been Locked
SBSYSULK - Front Panel has been Unlocked
Example : Lock Front Panel Buttons
SBSYSMLK - Send
SBSYSLOK - Rcvd
3. UNIT RESET
SBALLRST - Reset every output to Input 1
Unit will respond with
SBRSTACK - Unit has reset each Output to Input 1
Example : Reset all outputs to Input 1
SBALLRST - Send
SBRSTACK - Rcvd
6
RS-232 SERIAL COMMANDS
6 7
TYPICAL APPLICATION
AT-COMP-64M
PC RS232 Control
DVD Player
VCR Player
Satellite Receiver
HD Player
up to 4 HDTV’s
up to 6 Sources
CONTROL PORTS :
1. IR REMOTE - IR Remote Controller
2. RS 232 Interface - RS 232 interface system
INPUTS 1 - 6 HD SOURCE SIGNALS :
COMPONENT VIDEO - Component Video(YPBPR), RCA's
AUDIO - Stereo Audio, RCA's
OUTPUT 1 - 4 HDTV DISPLAY SIGNALS :
COMPONENT VIDEO - Component Video(YPBPR), RCA's
AUDIO - Stereo Audio, RCA's
8
INSTALLATION
Inhaltsverzeichnis
Andere Atlona Matrix-Umschalter Handbücher
Atlona
Atlona AT-HDMI-22M Bedienungsanleitung
Atlona
Atlona AT-UHD-PRO3-1616M Bedienungsanleitung
Atlona
Atlona AT-PROHD85M-SR Bedienungsanleitung
Atlona
Atlona AT-PRO3HD66M Bedienungsanleitung
Atlona
Atlona AT-VGA88M-SR Bedienungsanleitung
Atlona
Atlona AT-HD-V44M Bedienungsanleitung
Atlona
Atlona AT-HD-V44M Bedienungsanleitung
Atlona
Atlona AT-HD-V22M Bedienungsanleitung
Atlona
Atlona AT-HD-V42M Bedienungsanleitung
Atlona
Atlona AT-VGA0505 Bedienungsanleitung
Atlona
Atlona AT-HD-V42M Bedienungsanleitung
Atlona
Atlona AT-SAV-42M Bedienungsanleitung
Atlona
Atlona AT-AV0808N Bedienungsanleitung
Atlona
Atlona AT-H2H-44M Bedienungsanleitung
Atlona
Atlona AT-HD-V22M Bedienungsanleitung
Atlona
Atlona AT-HD88M-SR Bedienungsanleitung
Atlona
Atlona AT-HD-V42M Bedienungsanleitung
Atlona
Atlona AT-UHD-CLSO-824 Bedienungsanleitung
Atlona
Atlona AT-SDI52M Bedienungsanleitung
Atlona
Atlona AT-VGA0505 Bedienungsanleitung
