AUDAC LCR700 Montage- und Bedienungsanleitung

PROFESSIONAL AUDIO EQUIPMENT

LCR Meter LCR700

User Manual & Installation Guide

LCR70

LCR Meter

AUDAC

AUDAC PROFESSIONAL AUDIO EQUIPMENT

User Manual & Installation Guide

AUDAC

http://www.audac.be

[email protected]

INTRODUCTION.....................................................................................................................................................................................................................3

ENVIRONMENT......................................................................................................................................................................................................................4

SAFETY REQUIREMENTS ..................................................................................................................................................................................................5

GENERAL INFORMATION .................................................................................................................................................................................................6

OVERVIEW PANEL................................................................................................................................................................................................................7

SPECIFICATIONS ..................................................................................................................................................................................................................8

CAPITANCE ......................................................................................................................................................................................................................8

INDUCTANCE..................................................................................................................................................................................................................10

IMPEDANCE ....................................................................................................................................................................................................................12

GETTING STARTED ............................................................................................................................................................................................................13

1. AUTO POWER-DOWN................................................................................................................................................................................................13

2. FREQUENCY SELECT ...............................................................................................................................................................................................13

3. PARALLEL/SERIES MODE .......................................................................................................................................................................................13

4. RANGE BUTTON ........................................................................................................................................................................................................13

5. L/R/C FUNCTION BUTTON (ONLY MAIN DISPLAY) ..........................................................................................................................................14

6. Q/D/R FUNCTION BUTTON (ONLY SECOND DISPLAY) ...................................................................................................................................14

7. HOLD > 2SEC........................................................................................................................................................................................................14

8.MIN/MAX BUTTON .....................................................................................................................................................................................................14

9. SET ................................................................................................................................................................................................................................15

10. REL RELATIVE MODE (ONLY MAIN DISPLAY) ...............................................................................................................................................16

11. HI/LO LIMITS.............................................................................................................................................................................................................16

12. TOL .............................................................................................................................................................................................................................16

MAINTENANCE....................................................................................................................................................................................................................17

ADDITIONAL INFORMATION RS-232 COMMAND TABLE .....................................................................................................................................18

PERSONAL NOTES ..............................................................................................................................................................................................................22

Index

Introduction

Dear customer,

With the LRC Meter you have acquired a high-quality and state-of-the-art measurement appliance.

The device is essential to sound engineers because of its many possibilities. Users can carry out measurements

for induction, capacitance and impedance. During this action you can get a read-out on the D factor

(dissipation factor) on a second display. All measurements can be carried out on two different frequencies: 120

and 1.000 Hz. This allows a measurement of great accuracy.

The LCR700 has an Auto-Power OFF function, which helps conserve the lifespan of the battery, and a fuse

detection function to inform that a fuse is open or damaged. The use of a DC adapter can also serve to disable

the Auto Power OFF function. The RS232 port enables you to communicate with a computer.

Environment

Do not place the unit in environments which contain high levels of dust, heat, moisture or vibration.

Do not use the unit near water or other liquids. Make sure no water or other liquids can be spilled,

dripped or splashed on the unit.

This unit is developed for indoor use only. Do not use it outdoors.

Do not place objects on top of the unit.

Place the unit on a stable base.

Chapte

Safety Requirements

(Read the safety requirements before using the meter)

Warning:

Before taking any measurements, please isolate the DUT from the power supply.

You should remove the test leads from the meter before replacing the batteries in order to avoid an electric

shock. Make sure the circuit switch is disconnected before taking any measurements.

Do not use the meter if test leads look damaged. Please check regularly.

Caution:

When you can’t turn on the meter…

1. When you have turned off the meter a few seconds ago, it is perfectly normal. Please wait a moment to turn

it on again.

2. When you can’t operate the meter properly, please turn it off and restart later.

3. When the segments are fading away gradually, please wait 10 seconds to restart the meter.

4. When you can’t turn on the meter normally, please press the power key for 10 seconds and the meter will

restart.

General information

Display L\C\R-4 ½ digits, max. reading of 19999.

Q\D\R-4 digits, max.. reading of 9999 (Auto

range)

Measurement parameters Ls + (Q, D, Rs), Lp + (Q, D, Rp).

Cs+(Q,D,Rs),Cp+(Q,D,Rp).

Basic accuracy 0.5% for Impedance

0.7% for Inductance, Capacitance

Measuring range control Auto & manual

Overload indication “OL” display.

Test frequency 1KHz & 120 Hz

Low battery indication The indicator is displayed when the battery

voltage drops below the operating level and it

cancels all the memorized values to store into

EEPROM (included SET values).

Measurement speed once per second, nominal.

Operating environment 0°C to 50 °C at < 80% RH..

Storage environment -20°C to 60°C at 0 to 80% RH. With battery

removed from meter.

Power Single standard 9 Volt battery (NEDA 1604,

IEC 6F22 006P)

External power Adaptor 12 Volt min to 15 Volt max/50mA

(optional)

Auto power Auto power of if unused for 10 minutes

FUSE warning Indicates when a fuse is open of damaged.

Protective Fuse 0.1 A fast-blow 250V AC.

Dimensions 19.2 cm (Height), 9.1 cm (width), and 5.25 cm

(thickness).

Weights 365g (battery and holster included).

Accessories A pair of test leads, instruction manual, Software,

Optical data cable (9V battery and spare fuse in the

meter).

Chapte

Overview panel

APO Auto power off

RS232 Communication indicator

R Recording mode indicator

MAX Maximum reading indicator

MIN Minimum reading indicator

AVG Average reading indicator

AUTO Autoranging indicator

H Data hold indicator

SET Set mode indicator

Relative mode indicator

TOL Tolerance mode indicator

PAL Parallel mode indicator

SER Series mode indicator

D Dissipation factor indicator

Q Quality factor indicator

R Parallel or Series Resistance

indicator

% Tolerance indicator (percentage)

1 KHz Frequency indicator

120 Hz Frequency indicator

LRC L, C or R function indicator

High limit and tolerance indicator

Low limit and tolerance indicator

Low battery indicator

Beep tone indicator for tolerance

mode

MKΩImpedance (Ohm) indicator

umH Inductance (Henry) indicator

munpF Capacitance (Farad) indicator

Specifications

CAPACITANCE:

Test Frequency 120 Hz

Range Min. Max. Cx DF Note

20mF 1µF 10.000mF +/- (5.0%rdg +

5counts)

DF<0.1

+/- (10%rdg +

100/Cx + 5counts)

DF< 0.1

After short cal.

2000µF 100nF 1999.9µ +/- (1.0%rdg + 5

counts)

DF<0.1

+/- (2.0%rdg +

100/Cx + 5counts)

DF<0.1

After short cal.

200µF 10nF 199.99µF +/- (0.7%rdg + 3

counts) DF<0.5 +/- (0.7%rdg +

100/Cx + 5 counts)

DF<0.5

20µF 1nF 19.999µF +/- (0.7%rdg +

3counts) DF<0.5 +/- (0.7%rdg +

100/Cx + 5counts)

DF<0.5

2000nF 100pF 1999.9nF +/- (0.7%rdg +3counts)

DF<0.5 +/- (0.7%rdg +

100/Cx + 5counts)

DF<0.5

200nF 10 pF 199.99nF +/- (0.7%rdg + 5

counts) DF<0.5 +/- (0.7%rdg +

100/Cx + 5counts)

DF<0.5

After open cal.

20nF 1pF 19.999nF +/- (1.0%rdg +

5counts) DF<0.1 +/- (2.0%rdg +

100/Cx + 5 counts)

DF<0.1

After open cal.

Chapte

TestFrequency1KHz

Range

Min. Max. Cx DF Note

2000µF 100nF 1000.0µF +/- (5.0%rdg + 5counts)

DF<0.1

+/- (10%rdg + 100/Cx + 5

counts) DF<0.1

After short

cal.

200µF 10nF 199.99µF +/- (1.0%rdg+ 3counts)

DF<0.5 +/- (2.0%rdg + 100/Cx

+5counts) DF<0.5

After short

cal.

20µF 1nF 19.999µF +/- (0.7%rdg +3counts)

DF<0.5

+/- (0.7%rdg + 100/Cx +

5counts) DF<0.5

2000nF 100pF 1999.9nF +/- (0.7%rdg +3counts)

DF<0.5)

+/- (0.7%rdg + 100/Cx +

5counts) DF<0.5

200nF 10pF 199.99nF +/- (0.7%rdg +5counts)

DF<0.1

+/- (0.7%rdg + 100/Cx +

5counts) DF<0.5

20nF 1pF 19.999nF +/- (0.7%rdg + 100/Cx

+5counts) DF<0.1

+/- (0.7%rdg + 100/Cx +

5counts) DF<0.1

After open

cal.

2000pF 0.1pF 1999.9pF +/- (1.0% rdg+5counts) +/- (2.0%rdg+ 100/Cx +

5counts) DF<0.1

After open

cal.

Inhaltsverzeichnis

Andere AUDAC Messgerät Handbücher

AUDAC

AUDAC SLM200 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung