AUDAC CS74 Bedienungsanleitung

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere AUDAC Sprecher Handbücher

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung

PROFESSIONAL AUDIO EQUIPMENT

Ceiling Speaker CS74

Installation Guide

Ceiling

Speake

r

CS74

AUDAC

1

Installation Procedure

1) Cut a hole in the ceiling on the desired mounting location of the loudspeaker with a diameter of 167

mm. The included cutout template can be used for marking.

2) Provide the loudspeaker connection cable through the mounting hole.

3) Take the loudspeaker, and remove the front grill.

The front grill can be removed by rotating the mounting clips outwards and pushing them down. The

fixing screws will push the front grill out.

4) Pull the mounting clips up again, and rotate them inwards, making the speaker fit through the

mounting hole in the ceiling.

2

5) Connect the loudspeaker connection cable with the power tap connection block. On this connection

block, several connections can be made for different power taps. Depending of the desired power,

connections can be made for 8 Ohm Low impedance application, or 6 Watt / 3 Watt / 1.5 Watt for

100 Volt applications.

Press the locking mechanism of the desired power tap down, and insert the connection cable. After

releasing the locking mechanism, the speaker connection cable is connected to the loudspeaker or

transformer.

Always connect the common of the amplifier output to the C terminal, and the positive amplifier

output to the desired terminal. (8 ΩFor low impedance applications and the desired power terminal for

100 Volt applications).

6) Once the connections are made, the loudspeaker can be installed in the provided mounting hole. Insert

the speaker in the provided mounting hole, and use a screwdriver for tightening the fixing screws.

Once the screws are tightened by a quarter turn, the mounting clip will rotate outwards and will be

locked behind the ceiling. From this moment, the loudspeaker cannot fall out the ceiling. To make the

speaker equal with the ceiling, the fixing screws should be tightened.

7) Once the mounting screws are tightened, the front grill can be assembled to the loudspeaker.

On locations where high vibrations may occur, it is recommended to push the included small rubber

pieces into the groove where the grill fits in. This small rubber pieces makes sure that the grill won’t

come out by vibrations.

3