Audiovox Prestige APS-15CH Bedienungsanleitung

128-6461

1 of 5

Model APS-15CH

Owner's Manual

2 Button Remote Security System

Congratulations! Your purchase of this state-of-the-art security system

expresses a deep concern for the security of your vehicle, its contents,

andpassengers. Tofullyappreciatethemanyfunctionsandsafeguards

incorporated in this system, please spend a few minutes reading this

manual. You may find unexpected features that could mean the

difference between “protected” and “fully protected”.

FEATURES :

w2 Two Button Programmable Code Hopping RF Transmitters

wTwo Channel Receiver ( capable of accepting 4 transmitters )

wCode Learning

wRemote Panic in all modes

wProtected Valet

w7 Function LED - Arm / Disarm / Zones 1, 2, & 3 / Valet / Arming

wIntrusion Alert with Memory

wAudible Arm / Disarm / Defective Zone / Tamper Confirmation

wInstant Siren Activation

wStarter Disable ( Optional relay required )

wTrue Last Door Arming ( hardwire only )

wDefective Zone By - Pass

wHardwire or Voltage Sense Selectable

wActive or Passive Arming Selectable

wUser Programmable Permanent Chirp Delete

w6 Tone Multi-Tone Siren

wAdditional Negative Trigger Input

wRF Inhibit with Ignition On

wParking Light Flasher

OPTIONS:

wPlug In Dual Stage Shock Sensor

wRemote Trunk Release

wRemote Keyless Entry

wMultiple Vehicle Capable

wRemote Starter

wRemote Power Window Roll Up

wRemote Garage Door Interface

128-6461

2 of 5

Page 2

ARMING THE SYSTEM: (ACTIVE)

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood, and trunk.

2. Press and release the ARMING button on the keychain transmitter. The siren will "chirp"

once,thevehicle'sparkinglightswillflashonce,thedoorswilllock(optional),andthedash

mounted LED will begin to slowly flash.

WARNING! Excessive pressure on the transmitter buttons will damage the internal

components on the circuit board. All that is required is a light push to the button.

NOTE: Ifthesiren"chirped"threetimeswhenARMING,thenoneoftheentrypoints(hood,trunk,

doors) has been left opened. Closing the hood, trunk, or doors will correct the problem

and you do not need to disarm the system to make the correction. If the siren "chirped" three

times, sometime after arming, the exclusive delayed dome light learn circuit has been

programmed and the system detected a open entry point after the learned delay expired.

Again,closing thehood, trunk,or doorswill correct theproblem andyou donot needto disarm

the system to make the correction.

ARMING THE SYSTEM: (PASSIVE)

1. Turn off the engine, exit the vehicle, close and lock all doors, hood, and trunk.

2. The dash mounted LED will begin to flash rapidly, indicating that the system is

automatically (passive) arming. As an added convenience, the automatic passive arming

willnotbeginuntilalldoorsandtrunklidareclosed,allowingpassengerstoexitthevehicle

at their convenience.

3. In 30seconds, youwill hear a single short "chirp" from the siren,and thevehicle's parking

lampswillflashone time, indicatingthe system isARMED. At this time,the dash mounted

LED will begin to flash slowly, providing a visual indication that the system is fully ARMED.

OPTION NOTE: If the optional (not included) power door lock interface has been

installed, the alarm control module can be programmed to...

a) Automatically lock the doors during step 3 above, or

b) Lock the doors only when the transmitter is operated

4. If you wish to arm the system immediately, simply press and release the ARMING button

on the keychain transmitter. The siren will "chirp" once, the vehicle's parking lamps will

flash once, the doors will lock (optional), and the dash mounted LED will begin to

slowly flash.

PROTECTION WHILE THE SYSTEM IS ARMED:

1. Opening any door, hood or trunk will cause the alarm to immediately sound. The siren

will continue to sound for 30 seconds, then stop and automatically re-arm the vehicle.

If the potential thief left a door opened, the siren will sound for six 30 second cycles, then

re-arm and ignore the opened door.

2. IftheOPTIONALShockSensorhasbeeninstalled,anystrongimpacttothevehicle’sglass

will cause the alarm to trigger for the full 30 second alarm cycle. If the Optional Dual Stage

Shock Sensor has been installed, in addition to above, any mild impact to the vehicle's glass

will cause the alarm to sound a short series of warning tones.

3. Whenever the system is armed, the dash mounted LED indicator will slowly flash.

This serves as a visual deterrent to the potential thief. The LED is a very low current

bulb, and will not cause the vehicle's battery to drain, even when left unattended for

extended periods.

128-6461

3 of 5

Page 3

4. Wheneverthe systemis triggered,thevehicle's parkinglights willflashfor the30second

alarm cycle, attracting added visual attention to the vehicle.

5. Whenever the system is armed, the vehicle's starter will be bypassed. If a thief should

choose to ignore the siren, the vehicle can not be started.

DISARMINGTHESYSTEM:

1. As you approach the vehicle, press and release the ARMING button on the keychain

transmitter.

WARNING! Excessivepressureonthetransmitterbuttons will damagetheinternalcomponents

on the circuit board. All that is required is a light push to the button.

2. The siren will "chirp" 2 times and the vehicle's parking lamps will flash two times.

3A. ACTIVE: The dash mounted LED will turn off, and remain off until the system is re-armed.

3B. PASSIVE: Never attempt to disarm the system from a distance that prevents you from

openinga doorwithin 30seconds. Since the systemisprogrammed forpassivearming,

it will begin to re-arm until a door is opened. Opening the door will suspend the passive

arming cycle.

INTRUSION WARNING SIGNALS:

The system will inform you if an intrusion attempt has occurred while you were away from the

vehicle. If an intrusion attempt has occurred, the siren will "chirp" 4 times when disarming the

system.

The vehicle's parking lights will also flash 3 times to indicate an intrusion has occurred. Enter

the vehicle and observe the dash mounted LED for further information.

1. If the LED is flashing one time... pause...one time... etc., then an intrusion attempt was

made to a light activated entry point, or the shock sensor was activated.

2. If the LED is flashing two times...pause...two times...etc., then an intrusion attempt was

made to the hood, trunk, or an optional sensor that has been connected to zone 2.

3. If the LED is flashing three times...pause...three times...etc., then an intrusion attempt was

made through one of the vehicle's doors.

These intrusion warning indicators are stored in the system's memory, and will only be erased

from memory when the ignition key is turned on.

VALET / SYSTEM OVERRIDE SWITCH:

The "Valet" switch allows you to temporarily bypass all alarm functions, eliminating the need

to hand your transmitter to parking attendants or garage mechanics. When the system is in

valet mode, all alarm functions are bypassed, however, the remote panic feature and remote

door locks (optional) will remain operational. To use the valet mode;

1. Enter the vehicle and turn the ignition key to the "on" position.

2. Press andhold thevalet push-button switchfor5 secondsuntilthe dashmountedLED turns

on solid. The LED will remain on as long as the system is in the valet mode.

3. To return to normal operation, with the ignition switch on, press and release the valet

push-button switch one time. The LED will turn off indicating the unit has been returned

to the normal mode of operation.

In the event you lose your keychain transmitter, or if the transmitter fails to disarm the system,

the valet switch can be used as a system override switch. Open the car door (the alarm

will sound). Turn the ignition key on, and press and hold the valet switch on. The

128-6461

4 of 5

Page 4

alarm will stop sounding, and the vehicle can now be started.

NOTE: Always remember to exit Valet Mode to ensure that the vehicle remains protected

at all times.

ELIMINATING THE ARM / DISARM CHIRPS:

The normal arming and disarming confirmation "chirps" can easily be turned on and off using

the valet push-button switch. To do this...

1. Turn the ignition key on, and then off.

2. Within 10 seconds of turning the ignition key off, press and release the valet

push-button switch three times.

3a. If,before proceedingwith step2,thechirps wereon, thenyou willhear2chirps toindicate

that the chirps have been turned off.

3b. If, before proceeding with step 2, the chirps were off, then you will hear 1 chirp to indicate

that the chirps have been turned on.

Note: Whenever the chirps are by-passed, the 3 chirp defect and 4 chirp intrusion indicator

will always operate. This feature will always warn you if there is a defective sensor

during the arming sequence or if the vehicle had been tampered with in your absence,

even if the normal arming and disarming chirps have been turn off.

REMOTEPANICOPERATION:

Thearming&disarmingbuttonon your keychaintransmitteralso functions asa"panic"switch

for instant activation of the alarm in emergency situations. To use the remote panic switch;

1. Press and hold the arming button on the keychain transmitter for 3 seconds or more.

The alarm will immediately sound.

2. To stop the alarm, press and release the arming button on the keychain transmitter.

If the button is not pressed, the alarm will automatically stop after 30 seconds.

WARNING! Excessive pressure on the transmitter buttons will damage the internal

componentsonthecircuit board. Allthat isrequired isa lightpush tothe button.

TRUNKRELEASE:

This security system has an additional feature that can be wired to a number of different

optional accessories. Some of the more common uses for this "channel" are:

lRemote Trunk Release - available for any vehicle with factory installed electronic

push-button trunk release.

lRemoteCarStarter -available formost automatictransmission,fuelinjected vehicles.

lRemote Window Roll Up - available for most vehicles equipped with power windows.

To activate the optional accessory:

Press and hold the smaller button on the keychain transmitter for approximately

3 seconds. If the system has been programmed differently by your installation center,

this output may be accessed by pressing buttons 1&2 simultaneously for 3 seconds.

NOTE: This feature will not operate when the vehicle's ignition key is turned "ON".

128-6461

5 of 5

Page 5

Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6461

APS-15CH

SYSTEM FUNCTIONS AT A GLANCE

DASH LED INDICATORS

RAPID FLASHING..............................................PASSIVE ARMING

SLOW FLASHING .............................................ARMED

OFF....................................................................DISARMED

ON - SOLID........................................................VALET MODE

3 FLASH ... PAUSE ...........................................INTRUSION ZONE 3

2 FLASH ... PAUSE ...........................................INTRUSION ZONE 2

**1 FLASH ... PAUSE ...........................................INTRUSION ZONE 1

SIREN CHIRP INDICATORS

*1 CHIRP ............................................................ ARM

*2 CHIRPS .......................................................... DISARM

3 CHIRPS ......................................................... ARM / ZONE ACTIVE

4 CHIRPS ......................................................... DISARM / INTRUSION

PARKING LAMPS (Optional)

1 FLASH ............................................................ARM

2 FLASH ............................................................DISARM

3 FLASH ............................................................DISARM / INTRUSION

** Where applicable.

*These chirps are optional and may be disengaged.

Optional Channel 2 Device

Starter Cut-out

Door Lock Interface

Shock Detector

Motion Detector

Hardwire

Your System Has These Features Activated:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Rampage AA-929 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-400 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-4631B Bedienungsanleitung

Audiovox

Audiovox PS-155CH Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9845B Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-785 Bedienungsanleitung

Audiovox

Audiovox AA-9005 Fehlerbehebungshandbuch

Audiovox

Audiovox Pursuit PRO-9671FT Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO9776C Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-410a Bedienungsanleitung

Audiovox

Audiovox Professional PS-330i Bedienungsanleitung

Audiovox

Audiovox PRO9845A Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-5730A Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9744 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-920 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-900 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9600 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-15R Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO9801 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-410 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9344WOT Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9744 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25-CL Bedienungsanleitung

Audiovox

Audiovox 5BCRCS Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung