Audiovox PRO 9644 Bedienungsanleitung

Model PRO 9644

Owner’s Manual

3 Button Remote Security System with Starter Disable

IMPORTANT !

In order to provide the highest possible level of security to your vehicle, this

system is equipped with selectable manual override circuitry. It is possible that you will need to

manually override your security system if the transmitter becomes lost, or inoperative due to

battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is

necessary to fully understand the procedure required to enable your vehicle in such situa-

tions. In addition, the chart on the last page of this manual has a section for the particular

features and options installed in your vehicle as well as the override method selected.

Valet

Switch manual override is pre-selected from the factory,

however, the system can be

configured for "Custom Code" operation. Confirm the override mode selected on the last page

of this manual and familiarize yourself with the section on it's operation.

FEATURES :

w2 Three Button Programmable RF Transmitters (capable of accepting 4 transmitters)

wSeparate Lock/Unlock Transmitter Buttons

wFive Channel Receiver

wAnti Code Grabbing Technology

wSelectable Manual Override Mode

wRemote Panic in all modes (Improved)

wProtected Valet

wUser Programmable Manual Override Code

w7 Function LED - Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming

wIntrusion Alert with Memory

wAudible Arm / Disarm / Defective Zone / Tamper Confirmation

wInstant Siren Activation

wStarter Disable

wTrue Last Door Arming ( hardwire only )

wDefective Zone By-Pass

wHardwire or Voltage Sense Selectable

wActive or Passive Arming Selectable

wSmart Disarming

wProgrammable Auto Lock On / Off

wProgrammable Auto Unlock On / Off

wProgrammable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L

wProgrammable Active or Passive Door Locks

wUser Programmable Permanent Chirp Delete

wOn Command RF Chirp Delete from Transmitter Or Selectable Through Software

w6 Tone Multi-Tone Siren, (And Or),

wCar Horn Activation for additional alarm response

wAdditional Negative Trigger Input

wRF Inhibit with ignition on

wParking Light Flasher

OPTIONS :

wRemote Trunk Release ( must have electronic trunk release )

wRemote Keyless Entry ( must have power door locks )

wIlluminated Entry

wMultiple Vehicle Capable

wHeadlight Illumination during Arming and or Disarming

wRemote Starter

wRemote Power Window Roll Up

wRemote Garage Door Interface

wPlug In Electronic Shock Sensor

YOUR " ANTI CODE GRABBING " TRANSMITTERS

The transmitters included with your new security system use the most advanced and

secure form of radio frequency transmission available on any current automotive security

system. Some of today’s sophisticated auto thieves use a device known as a code grabber,

which will receive and store the signal from your keychain transmitter, and re-transmit at a

later time to disarm your system.

Your anti code grabbing transmitters will change their signal every time the button is pressed,

so when a thief grabs then re-transmits your signal, the alarm system

will not

respond.

If your transmitter button is pressed more than fifty times while it is out of range of the vehicle

(children playing with your keys), the transmitter will not operate when you return to the

vehicle, and will need to be re-aligned to the receiver. To do this, simply press the Lock button

two times within a one second time period. The system will now respond to that transmitter

each time a button is pressed.

ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and release the Lock button on the keychain transmitter.

þRed dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren sounds one chirp.

If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.

Simply close the opened entry point to provide full protection. If the siren did

not sound when arming, then the chirps have been turned off, and you

shouldrefertothesectiontitled"ELIMINATING THE ARM / DISARM CHIRPS "

in this manual.

oVehicles horn beeps one time.

If the horn beeps three times, then you have left a door, trunk, or hood lid ajar.

Simply close the opened entry point to provide full protection. If the horn did

not sound when arming, then the chirps have been turned off, and you

shouldrefertothesectiontitled"ELIMINATING THE ARM / DISARM CHIRPS "

in this manual.

oDoors Lock - Optional

oHeadlightIllumination- Optional

The vehicle’s headlights turn on for approximately 30 seconds, illuminating

the path as you leave the vehicle.

SILENT ARMING - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold the Lock button on the keychain transmitter for 2 seconds.

þRed dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren will not sound.

If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.

Simply close the opened entry point to provide full protection.

oVehicles horn will not beep.

Page 2

If the horn beeps three times, then you have left a door, trunk, or hood lid ajar.

Simply close the opened entry point to provide full protection.

oDoors Lock - Optional

oHeadlightIllumination- Optional

The vehicle’s headlights turn on for approximately 30 seconds, illuminating the

path as you leave the vehicle.

ARMING THE SYSTEM - PASSIVE ( AUTOMATIC )

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and trunk lid.

þRed dash mounted LED begins to flash rapidly, indicating 30 second passive

arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle will immedi-

ately suspend automatic arming, and the 30 second passive arming cycle will re-start

when all doors are closed. At the end of the passive arming cycle;

þRed dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren sounds one chirp

If the siren did not sound when arming, then the chirps have been turned off,

and you should refer to the section titled "ELIMINATING THE ARM / DISARM

CHIRPS"inthismanual.

oVehicles horn beeps one time.

If the horn did not sound when arming, then the chirps have been turned off,

and you should refer to the section titled "ELIMINATING THE ARM / DISARM

CHIRPS"inthismanual.

oDoors Lock - Optional

Door locking during passive arming is a selectable feature. The alarm can be

programmed to allow the doors to lock only when arming using the keychain

transmitter, and they will not automatically lock during passive arming.

PROTECTION WHILE THE SYSTEM IS ARMED

þOpening any protected door, hood, or trunk lid will cause the alarm to immediately

sound. The alarm will continue to sound for 30 seconds, then stop and continue to

monitor all protected entry points. If the thief left a door opened, the alarm will sound

for six 30 second cycles, remain armed, and ignore that triggered zone.

þWhenever the system is armed, the red dash mounted LED indicator will slowly flash.

This serves as a visual deterrent to the potential thief. The LED is a very low current

bulb, and will not cause the vehicle’s battery to drain, even when left unattended for

extended periods.

þWhenever the system is triggered, the vehicle’s parking lights will flash for the full 30

second alarm cycle, attracting visual attention to the vehicle.

oWhenever the system is triggered, the vehicle’s horn will beep for the full 30 second

alarm cycle, attracting added attention to the vehicle.

oOptional - Whenever the system is triggered, the interior courtesy lights will flash for

the full 30 second alarm cycle.

þWhenever the system is armed, the vehicle’s starting circuit will be bypassed. If the

thief should choose to ignore the siren, the vehicle can not be started

Page 3

oOptional - Any strong impact to the vehicle’s glass will cause the alarm to trigger for

the full 30 second alarm cycle.

DISARMING THE SYSTEM

1. As you approach the vehicle, press and release the Unlock button on the keychain trans-

mitter.

þRed dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will start

flashing rapidly, indicating that the system is re arming automatically. Open

any door to suspend the automatic arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in your

absence. Before turning the key on, examine the LED to identify which zone

was triggered.

þSiren sounds two chirps.

If the siren sounds 4 chirps, then the alarm was triggered in your absence.

Beforeturningthekeyon, examinetheLED andreferto theINTRUSIONWARN-

ING SIGNALS section of this manual to identify which zone was triggered.

If the siren did not sound when disarming, then the chirps have been turned

off, and you should refer to the section titled " ELIMINATING THE ARM /

DISARMCHIRPS " in this manual.

oVehicle's horn beeps two times.

If the horn beeps four times, then the alarm was triggered in your absence.

Before turning the key on, examine the LED and refer to the INTRUSION

WARNING SIGNALS section of this manual to identify which zone was trig-

gered.

If the horn did not sound when disarming, then the chirps have been turned

off, and you should refer to the section titled " ELIMINATING THE ARM /

DISARMCHIRPS " in this manual.

oDoors Unlock - Optional

oTwo Step Doors Unlock - Optional

If, when the Unlock transmitter button was pressed and released, only the

drivers door unlocked, then you have the two step unlock option installed.

Pressing the unlock button a second time will unlock all other doors.

oHeadlightIllumination- Optional

The vehicle’s headlights turn on for approximately 30 seconds, illuminating

the path to the vehicle.

oCourtesy Lights - Optional

Interior courtesy lights turn on for 30 seconds, or until the ignition key is switched

on.

SILENT DISARMING

1. As you approach the vehicle, press and hold the Unlock button on the keychain transmit-

ter for 2 seconds.

þRed dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will start

Page 4

flashing rapidly, indicating that the system is re-arming automatically. Open

any door to suspend the automatic arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in your

absence. Before turning the key on, examine the LED to identify which zone

was triggered.

þSiren will not sound.

If the siren sounds 4 chirps, then the alarm was triggered in your absence.

Before turning the key on, examine the LED and refer to the INTRUSION

WARNING SIGNALS section of this manual to identify which zone was trig-

gered.

oVehicles horn will not beep.

If the horn beeps four times, then the alarm was triggered in your absence.

Before turning the key on, examine the LED and refer to the INTRUSION

WARNING SIGNALS section of this manual to identify which zone was trig-

gered.

oDoors Unlock - Optional

oTwo Step Doors Unlock - Optional

If, when the Unlock transmitter button was pressed and released, only the

drivers door unlocked, then you have the two step unlock option installed.

Pressing the unlock button a second time will unlock all other doors.

oHeadlightIllumination- Optional

The vehicle’s headlights turn on for approximately 30 seconds, illuminating

the path to the vehicle.

oCourtesy Lights - Optional

Interior courtesy lights turn on for 30 seconds, or until the ignition key is

switched on.

WHILE THE SYSTEM IS SOUNDING

If during a triggered state, you wish to shut off the siren without disarming your security

system, simply press and release any transmitter button other than the disarm button. This

action will turn off the siren yet leave the vehicle fully armed and protected. This feature is

particularly useful if you are aware of children playing near your vehicle that may accidently

trigger your security system. In this case you can cancel the siren sounding without disarm-

ing your system.

INTRUSIONWARNINGSIGNALS

This system will inform you if an intrusion attempt has occurred while you were away from

the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking

lights will flash 3 times when disarming the system. Enter the vehicle, and observe the red

dash mounted LED to identify which zone was triggered.

If the LED is flashing one time...pause...one time...pause...etc., then an intrusion

attempt was made to the OPTIONAL shock sensor, or an accessory triggering

device that may have been added to the system.

If the LED is flashing two times...pause...two times...pause...etc., then an intrusion

attempt was made to a hood or trunk pin switch that was added to the system, or

Page 5

to a light activated entry point if the alarm was installed using the voltage sensing

feature.

If the LED is flashing three times...pause...three times...pause...etc., then an

intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory, and will only be

erased when the ignition key is turned on.

VALET SWITCH

The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to

hand your transmitter to parking attendants or garage mechanics. When the system is in valet

mode, all alarm functions are bypassed, however the remote panic feature and remote door

locks will remain operational. To use the valet mode, the system must first be disarmed either

by using your keychain transmitter, or by activating your personalized manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid. The

system will remain in the valet mode.

3. To return to normal operation, press and release the pushbutton switch any time the

ignition is on.

NOTE: Always remember to exit the valet mode. This will ensure that the vehicle remains

protected at all times.

MANUALLYOVERRIDINGYOURSYSTEM:

USING THE VALET SWITCH MANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter. This is

necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its

battery fails. If your system has been selected for Valet Switch manual override as indicated

on the last page of this manual, to by-pass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet pushbutton switch.

The alarm system will stop sounding and enter the (by-passed) mode. You can now start and

operate the vehicle normally.

Typically this override mode is used only if the transmitter has become inoperative.

Programming Your Custom Override Code:

Unlike override switches easily found, and defeated, this security system allows the con-

sumer to program a personal override code, offering a higher level of security. To take

advantage of this option, programmable feature # 10 must be selected for the Custom Code

Option. Consult your installation center for programming details. The system comes from

the factory with a pre-programmed override code of 11. To change this default override

code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency override se-

quence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the valet/override switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will

beep and the lights will flash one time.)

Page 6

Page 7

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the

pushbutton switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the

pushbutton switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by flashing

the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the

new code three times with a one second pause between each code, then the system will

begin arming. If the LED flash pattern reports the previously stored code, the new code was

not entered correctly. Please repeat steps 1 through 7 above considering the following.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0

(Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of in activity expire, or if the ignition switch is turned off for more than

5 seconds during any of the above steps, the unit will revert back to the last

successfully stored code.

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to "52" you would do the

following:

1. Disarm the system by use of the transmitter, or by use of the emergency override se-

quence.

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the valet/override switch, 3 times.

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will

beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the push button switch to set the tenths

digit. (As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the push-button, turn the ignition switch off then

on.

7. Within 10 seconds, begin to press and release the push button switch to set the units

digit. (As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern.

You will note the LED flashing five times, pause, and then flash two times, pause. This

pattern will be repeated three times indicating the new code (52) has been accepted and

stored in memory.

NOTE: If after step 7, the LED flashes a code other than what was just entered, this

indicates that the code has not been changed. You will have to repeat steps 1

through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no

digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then

5 seconds during any of the above steps, the unit will revert back to the last

successfully stored code.

Page 8

MANUALLYOVERRIDINGYOURSYSTEM:

USINGTHE CUSTOM CODE OVERRIDE

Assuming the override code programmed has not been changed, and the default override

code of 11 is in the system's memory.

1. Enter the vehicle and turn the ignition switch to the on position.

NOTE: The siren will sound.

2. Within 5 seconds, press and release the pushbutton switch 1 time.

3. Within 5 seconds, turn the ignition switch off then on.

4. Within 5 seconds, press and release the pushbutton switch 1 time.

5. Turn the ignition switch off then on and start the vehicle.

NOTE: If you have changed the programmed override code then substitute your new code

tenths for step 2 above, and units for step 5 above.

ELIMINATING THE NORMAL ARM / DISARM CHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any time you arm

or disarm the system simply by holding the Lock or Unlock button for two seconds. If you

find the normal arming and disarming chirps annoying, they can be turned off permanently,

eliminating the need to hold the transmitter buttons during the arming or disarming function,

To do this,

1. Then turn the ignition key on then off.

2. Within 10 seconds, press and release push-button switch three times.

3. If the chirps were on before you started, then you will hear 2 chirps indicating they have

been turned off.

If the chirps were off before you started, then you will hear one chirp indicating they have

been turned on.

NOTE: Whenever the chirps are by-passed, the 4 chirp intrusion indicator and 3 chirp

defective zone indicator will always operate. Since these are important warnings

to you that something has happened, they cannot be eliminated.

REMOTEPANIC OPERATION

The Lock or Unlock button on your keychain transmitter also functions as a panic switch for

use in emergency situations. To use remote panic,

1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more

seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for

3 seconds. If the button is not pressed, the alarm will automatically stop after 30 sec-

onds. Also if any transmitter button other than the Lock or Unlock button is pressed and

released, the Panic mode will be turned off immediately. The normal function of this

transmitter button will be suspended during the Panic sounding period.

NOTE: While in the Panic mode, pressing and releasing the Lock, or the Unlock buttons will,

if the option is installed, lock and unlock the doors respectively. While in the panic

mode, anytime the unlock button is pressed, the panic feature will continue for the

allotted 30 seconds, however, the security system will be disarmed allowing the

vehicle to start.

Page 9

OPTIONAL DEVICE OUTPUT (CHANNEL 3)

Controlled By: oOption Button, oBoth Lock & Unlock Button, oBoth Option & Lock

Button, or Both Option and Unlock Button.

This security system is equipped with an output which will activate when the appropriate

transmitter button is depressed for four seconds. Optional devices that may be connected to

this channel are:

oRemote Electric Trunk Release

oRemote Car Starter

oRemote Window Closure

oRemote Garage Door Interface

NOTE: In addition there may be a second optional feature connected to your system that

when the same transmitter button is pressed and released 2 times within 3 seconds

(double pressed), the second optional feature will activate. This output is typically

used for a remote start option and will likely prevent inadvertent activation of the

remote start device if young children are playing with the hand held transmitter.

If your vehicle is not equipped with an electronic trunk release switch, or other option listed,

this feature may have been connected to another accessory. Please ask your dealer for

further information.

ADDITIONAL REMOTE FUNCTION (CHANNEL 4)

Controlled By: oOption Button, oBoth Lock & Unlock Button, oBoth Option & Lock

Button, or Both Option and Unlock Button.

This security system has an additional feature that can be connected to a number of

different optional accessories. Some of the more common uses for this channel are:

oRemote Car Starter

oRemote Window Closure

oRemote Garage Door Interface

To remotely operate the device indicated, momentarily press, or press and hold the appro-

priate transmitter button(s) as indicated above.

ADDITIONAL REMOTE FUNCTION (CHANNEL 5)

Controlled By: oOption Button, oBoth Lock & Unlock Button, oBoth Option & Lock

Button, or Both Option and Unlock Button.

This security system has an additional feature that can be connected to a number of

different optional accessories. Some of the more common uses for this channel are:

oRemote Car Starter

oRemote Window Closure

oRemote Garage Door Interface

To remotely operate the device indicated, momentarily press, or press and hold the

appropriate transmitter button(s) as indicated above.

PRO9644

SYSTEMFUNCTIONSATAGLANCE

DASHLEDINDICATORS

RAPIDFLASHING = PASSIVEARMING

SLOWFLASHING = ARMED

OFF = DISARMED

ON SOLID = VALETMODE

3FLASH...PAUSE = INTRUSION ZONE 3

2FLASH...PAUSE = INTRUSION ZONE 2

1FLASH...PAUSE = INTRUSION ZONE 1

SIRENAND/ OR HORN CHIRP INDICATORS

1 CHIRP * = ARM

2 CHIRPS * = DISARM

3 CHIRPS = ARM/DOOR OPENED

4 CHIRPS = DISARM/INTRUSION

* These chirps are optional, and can be de - activated.

PARKINGLAMPINDICATORS

1 FLASH = ARM

2 FLASHES = DISARM

3 FLASHES = DISARM /INTRUSION

Your System Has These Features Activated

oRemote Keyless Entry

oIlluminated Entry

oAuto Lock with ignition key

oAuto Unlock with ignition key

oHeadlight Illumination during arm & disarm

oPassive Arming

oNo Lock in passive mode

oHardwire doors, hood, and trunk

oCustom Code Override

oValet Switch Override

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox 128-7404A Bedienungsanleitung

Audiovox

Audiovox PRO-9342FT3WOS2 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-5730A Bedienungsanleitung

Audiovox

Audiovox APS-25C Bedienungsanleitung

Audiovox

Audiovox CarLink ASCL1 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9842B Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-400 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9232a Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9800 Bedienungsanleitung

Audiovox

Audiovox APD-510 Bedienungsanleitung

Audiovox

Audiovox Prestige 128-8615 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25HJ Bedienungsanleitung

Audiovox

Audiovox APS255A - Car 2 Prestige Platinum Code Learning 3 Button Security... Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9544FT Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25CH Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9246FT Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-900 Bedienungsanleitung

Audiovox

Audiovox APS996A - Prestige Remote Security System Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-998 Bedienungsanleitung

Audiovox

Audiovox PRO-9649a Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9642 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9776N Series Bedienungsanleitung

Audiovox

Audiovox Pursuit Series Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9744 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung