Audiovox Pursuit PRO 9232a Bedienungsanleitung

128-6627

1 of 8

KEYLESS ENTRY ALARM UPGRADE MODULE

PRE - INSTALLATION NOTES :

Thissystemprovidesanoutputthatis usedtodrivethesiren,andanoutputthatcanpulsethevehicle'shorn.When

utilizing the horn, an additional relay maybe required. Caution: on many vehicles the factory horn is not

designedfor continuoususe, andit isrecommended thatthe sirenis usedfor thesevehicles. Checkto see

ifthe horn inthe vehicle isthe same partthat is usedin a vehiclewith the factoryinstalled securitysystem.

STAND ALONE PASSIVE ALARM

When installing the PRO-9232 as a stand alone passive alarm system, the following programmable features must

be set:

Feature #5 set to Passive.

Feature #7 set to Delay.

Feature #8 set to 1 Wire Disarm.

IMPORTANT

: In the entry delay mode, when the alarm is armed actively, the doors will trigger the alarm

instantly. The entry delay will only take place when the alarm is allowed to arm passively!

IMPORTANT

: THE ENTRY DELAY WILL NOT OPERATE WHEN THE VOLTAGE SENSING CIRCUIT,

FEATURE # 6, IS ACTIVE

AUXILIARY FUNCTION or REMOTE START OUTPUT

Thissystemincludesanadditionaltransistorizedgroundoutputthatcanbeusedtotriggeranexternalremotestarter

or remote window closure module. This is the Green w/Black trace wire, and it is activated by pressing the Lock,

then Unlock, then Lock buttons on the factory transmitter within a 3 second time period.

REMOTE PANIC

This system will allow the activation of remote panic using the factory transmitter. Pressing the Unlock, the Lock,

then Unlock buttons on the factory transmitter within a 3 second time period will activate the remote panic feature.

TRUNK TRIGGER BY - PASS INPUT

This system provides a positive trunk release input, which allows the activation of the remote trunk release from

the OEM transmitter without triggering the alarm, even when the system is armed.

VALET / MANUAL OVERRIDE SWITCH

This system provides a valet/manual override switch which is operable by use of a custom code override or only

after the system is disarmed. There is no need to conceal this switch as the override code is known only to the

operator. UNDERSTANDING DISARM #1 AND #2:

Becauseof the complexities of thedifferent factory installed RemoteKeyless Entry Units onthe market today, the

PRO-9232usestwodisarminputs. Whetherinstallingintoavehicleusinga2-stepunlockcircuit,singlestepunlock

circuit, or as a stand alone passive alarm, both disarm wires must be connected in all installations.

The arm and disarm functions of this system are learned during power up, by monitoring the resting state of the

factory wires when power is applied to the unit. Be certain all wires are connected to the vehicle before applying

power to the circuit to insure the system responds only during operation from the factory transmitters.

NOTE: By design, if feature #8 is set to the "ON" position, (1 wire disarm), the alarm will not disarm while the

system is in the triggered mode.

Model PRO 9232a

INSTALLATIONINSTRUCTIONS

128-6627

2 of 8

INSTALLATION OF MAJOR COMPONENTS :

ALARMCONTROLMODULE

Select a mounting location inside the passenger compartment ( up behind the dash ), and secure it using screws, or

cable ties. Do not mount the control module in the engine compartment, as it is not waterproof. Do not mount the unit

or route the wiring near the steering shaft, as it might become entangled preventing proper operation of the vehicle.

LED&VALET/OVERRIDESWITCHASSEMBLY

The LED & Valet/Override switch assembly are provided for to facilitate installation. The unit should be affixed to the

lower lip of the dash allowing the LED to be visible from outside the vehicle and the pushbutton switch accessible to

the operator of the vehicle.

In many installations it may be necessary or desired to separate the switch and the LED and mount these components

apartfrom each other. Ifthis is therequest of thecustomer, or thepreferred method ofinstallation, follow theinformation

below:

LED

The LED will serve as a visual indicator of the alarm status. It should be installed into the dashboard, located where

it is easily seen from outside the vehicle, yet not distracting to the driver. If the direct mounting is the preferred method

of installation, once a location has been selected, check behind the panel for wire routing access, and to confirm the drill

will not damage any existing components as it passes through the panel. Drill a 1/4 “ diameter hole, and pass the red

and blue wires from the LED through the hole, from the front of the panel. Firmly press the body of the LED into the hole

until fully seated.

VALET/OVERRIDESWITCH

Select a mounting location for the valet/override pushbutton switch, that is easily accessible to the driver of the vehicle.

Theswitch doesnothave tobe concealed asit cannotdisarm the systemwithout theproperprogrammed overridecode.

The valet switch may be mounted below or on the dashboard by drilling a 9/32 “ diameter hole in the selected location.

Before drilling, be sure to check the area behind the panel for adequate clearance for the body of the switch, and to be

sure that the drill will not damage any components as it passes through the panel.

SIREN

Select a mounting location in the engine compartment that is well protected from access below the vehicle. Avoid areas

near high heat components or moving parts within the engine compartment. To prevent water retention, the flared end

of the siren must be pointed downward when mounted.

Mount the siren to the selected location using the screws and bracket provided.

HOOD AND TRUNK PIN SWITCHES

Two pin switches are included for use in protecting the hood and trunk ( or hatchback ) of the vehicle.

The switches must always be mounted to a grounded, metal surface of the vehicle. It is important to select a location

where water cannot flow or collect, and to avoid all drip gutters on hood and trunk fender walls. Choose locations that

are protected by rubber gaskets when the hood or trunk lid is closed.

The pin switches can be mounted using the brackets and screws provided, or directly mounted by drilling a

1/4 “ diameter mounting hole.

Keep in mind that when properly mounted, the plunger of the pin switch should depress at least 1/4 “ when the hood or

trunk lid is closed.

WIRING THE SYSTEM :

14 PIN CONNECTOR

RED FUSED WIRE: + 12 VDC CONSTANT BATTERY SOURCE

In all installations, the RED wire will be connected to a + 12 VDC constant battery source.

When voltage sensing, the RED wire provides power to the circuit and controls the sensitivity of the voltage sensing

circuit,whichdetectstheturningonofaninteriorlightwhenadoorisopened.Itwillalso detecttheswitchingonofparking

orheadlamps,and inmanycases willtriggerthealarmwhenathermostaticallycontrolledelectroniccoolingfan switches

on.

In voltage sensing applications, the closer to the battery that this wire is connected, the less sensitive the voltage sense

circuitrywillbe. Moving the connectionpoint to the fusepanelwill increase the sensitivityofthe voltage sensing circuitry.

Page 2

128-6627

3 of 8

It is recommended that when installing this system into vehicles with electronic “ after fans, “ the procedure for hardwire

should be followed.

HARDWIRE:

When hardwiring the door trigger input to switches at all points of entry, the voltage sense circuit must be disabled. By

default, programmable feature # 6 is set to "Hardwire" therefore no change is required. If however you are setting the

unit as a voltage sensing alarm, feature #6 must be changed and voltage sensing must be turned on.

WHITE WIRE : + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 A MAX )

This wire is provided to flash the vehicle’s parking lights. Connect the WHITE wire to the positive side of one of the

vehicle’s parking lights.

WHITE w/ BLACK TRACE WIRE : POSITIVE OUTPUT TO SIREN

This is a + 12 VDC transistorized switched output when triggered.

Connect this wire to the red, positive wire of the siren. Secure the black, ground wire of the siren to chassis ground.

PURPLE WIRE : (+) DOOR TRIGGER

If the vehicle’s door courtesy light switches have a + 12 VDC output when the door is opened (most Fords), you must

connect this wire to the positive output from one of the door switches. Do not connect this wire at the illuminated entry

output from the keyless entry module. You must connect this wire at the door ajar switch. In most cases, the PURPLE

wire will only need to be connected to one door switch, no matter how many doors the vehicle has.

IMPORTANT!

DonotusethePURPLEwireifthevehiclehasgroundoutputtypedoor switches.(seeBROWNwire).

Note: For vehicles with interior delay lighting see programming under title "Completing The Installation".

YELLOW WIRE : +12VDC IGNITIONSOURCE

Connect this wire to a source that is + 12 VDC when the key is in the on and crank positions, and off when the key is

in the off position.

DARKGREENw/WHITETRACEWIRE:ENTRYILLUMINATION(300mAMAX.)

The DARK GREEN w/ WHITE TRACE wire provides a 30 second ground signal whenever the system is disarmed using

the OEM transmitter, and pulses ground when the alarm is triggered.

It is used to provide the optional entry lighting feature, and will flash the vehicle’s dome light when the alarm is sounding.

This is a transistorized, low current output, and should only be used to drive an external relay coil. Connect the DARK

GREEN w/ WHITE TRACE wire to terminal 86 of an external relay, connect terminal 85 of the relay to a fused + 12 VDC

battery source, and wire the normally open and common relay contacts ( 87 and 30 ) according to the polarity of the

vehicle’s courtesy light circuit.

BLACK w /WHITE TRACE WIRE: LOW CURRENT HORN OUTPUT

The black w/ white trace wire is provided to beep the vehicle’s horn. This is a transistorized low current output, and

should only be connected to the low current ground output from the vehicle’s horn switch.

If the vehicle uses a + 12 VDC horn switch, then connect the black w/ white trace wire to terminal 86 of the AS 9256

relay ( or an equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12 VDC battery source.

Connect relay terminal 87 to the vehicle’s horn switch output, and connect relay terminal 30 to a fused + 12 VDC battery

source.

BLACK WIRE : CHASSIS GROUND

Connect this wire to a clean, solid, unpainted, metal part of the vehicle’s chassis.

ORANGE WIRE : GROUND OUTPUT WHEN ARMED

This wire is provided to control the starter cut relay. Connect the ORANGE wire to terminal 86 of the relay, and wire the

remaining relay contacts as shown in the wiring diagram.

WARNING!

Audiovox does not recommend using this relay to interrupt the ignition wire. Only connect

this relay to the low current solenoid feed wire, as indicated on the wiring diagram.

BROWN WIRE : (-) DOOR TRIGGER

If the vehicle’s door courtesy light switches have a negative ground output when the door is opened (most GM and

Imports) you must connect this wire to the negative output from one of the door switches. Do not connect this wire at the

illuminatedentryoutputfromthekeylessentrymodule. Youmustconnectthiswireatthedoorajarswitch. Inmostcases,

the BROWN wire will only need to be connected to one door switch, no matter how many doors the vehicle has.

IMPORTANT!

DonotusetheBROWNwireifthevehiclehas+12Voltoutputtypedoorswitches(seePURPLEwire).

Page 3

128-6627

4 of 8

Note: For vehicles with interior delay lighting see programming under title "Completing The Installation".

LIGHTGREENWIRE:(-)INSTANTTRIGGERZONE1

This is an instant activation ground trigger wire. This wire should be reserved for connection to optional ground output

trigger devices such as motion, glass breakage and/or non plug in shock sensors.

DARK GREEN WIRE : (-) INSTANT TRIGGER ZONE 2

This is an instant activation ground trigger wire. It should be connected to the previously installed hood and trunk pin

switches.

GREEN w/BLACK TRACE WIRE : AUXILIARY OR REMOTE STARTER OUTPUT

Thiswireprovides a low currenttransistorizedground pulse to controltheinput trigger wire ofaremote starter or window

roll-up module. Connect this wire to the ground activated trigger input wire of the optional device.

2 PIN WHITE CONNECTOR : RED AND GREEN DOOR LOCK OUTPUTS (Auto Lock / Unlock)

The door lock output wires from this unit will provide control for the passive lock feature as well as ignition controlled lock

and unlock feature, and should be used only on vehicles whose Factory Keyless Entry circuits do not incorporate these

features.

These wires will provide either a pulsed ground output to the factory door lock control relay, or a pulsed +12 volt output

to the factory door lock control relay. In either case, the maximum current draw through these outputs must not exceed

300 mA.

3 Wire Ground Switched Door Locks

In this application, the red wire provides a ground pulse during the lock sequence. Connect the red wire to the wire that

provides a low current ground signal from the factory door lock switch to the factory door lock control relay.

The green wire provides a ground pulse during the unlock sequence. Connect the green wire to the wire that provides

a low current ground signal from the factory door unlock switch to the factory door unlock control relay.

3 Wire Positive Switched Door Locks

In this application, the red wire provides a positive pulse during the unlock sequence. Connect the red wire to the wire

that provides a low current positive signal from the factory door unlock switch to the factory door unlock control relay.

The green wire provides a positive pulse during the lock sequence. Connect the green wire to the wire that provides a

low current positive signal from the factory door lock switch to the factory door lock control relay.

4 Wire Polarity Reversal and

5 Wire Alternating 12 Volt

Door Lock Control Circuits

In these applications, the AS 9159 Door Lock Interface (or equivalent 30 A automotive relays) must be used. Refer to

the AUDIOVOX Door Lock Wiring Supplement for proper connection to these types of circuits.

4PINWHITECONNECTOR: GREEN/BLACK,RED, GREEN, RED/BLACK,&BLUEFACTORYKEYLESSINPUTS:

NOTE!

When installing the PRO-9232 as a stand alone passive security system, the RED wire in this connector

must be connected to a rest at ground , + 12 VDC switched ignition source. RED w/BLACK and GREEN

wires must be connected to ground. The BLUE wire in this connector will not be required for the stand

alone installation.

The Green/Black, Red, Green, and Red/Black wires of the 4 pin connector are polarity learning inputs to be connected

to the vehicle unlock 1, and unlock 2 control wires. When the control circuit is first powered up, these wires will learn

therestingstateofthecircuitstheyareconnectedto. DONOToperatethevehicle'sdoorlockcircuits, (switchorremote),

while power is being applied to the PRO-9232.

WIRING THE ARM / DISARM INPUTS IN VEHICLES WITH REMOTE 2 STEP UNLOCK

Thefollowing represents themost common wiringroutine in vehiclesusing the remote2 step unlockfeature.

GREEN/BLACKWIRE:ARMINPUT#2

Connect this wire to the vehicles door lock switch input wire, which will receive either a switched positive or

switchednegative whenthe doorlock switchis movedto thelock position. This wire will be used to compare

thetwo inputs Arm#1 & Arm#2. If bothinputs are activeat thesametime, thevehicle will notarm. The intent

ofthis wire isto prevent thesystem fromarmingwhen thein vehicle doorlock switch isused to lockthe doors,

insuringonlythe transmitterarms the system. Ifyou do notdesire this featureor the customerprefers that the

Page 4

128-6627

5 of 8

door lock switch arm the system as well as the transmitter, connect this wire to chassis ground.

REDWIRE:DISARMINPUT#1

Connectthiswiretothedriver'sdoorunlockmotorwire,whichwillreceiveanegativeorpositivepulsewhenthe

driversdoorisunlockedwiththeremotetransmitter,andthedoorswitch,butdoesnotreceiveapulsewhenall

doorsare unlocked usingthe remotetransmitter.

GREENWIRE:ARMINPUT#1

Connectthiswiretothelocksideofthedoorlock/unlockswitchor,thedriver'sdoorlockmotorlegwire,which

willreceiveanegativeorpositivepulsewhenthedoorsarelockedusingthedoorswitchortheremotetransmitter.

REDw/BLACKTRACEWIRE:DISARMINPUT#2

Connect this wire to the unlock side of the door lock/unlock switch or any passenger door unlock motor wire,

whichwillreceiveanegativeorpositivepulse whenall doors are unlocked usingthedoorpanelswitchorthe

remotetransmitter,butwillnotreceive apulsewhenthe driver only doorisunlocked using theremote

transmitter.

NOTE: TheGreen/Black/Red/Green/&Red/BlackwiresMUSTbeconnectedtotheirrespectivesourcebefore

poweringupthemoduleasthesewirearepolaritylearnandwillnotfunctionproperlyifconnectedafterpower

up. Inaddition,these wiresifnotusedasindicated above must beconnectedtoground. Thiswill insure

properoperationandpreventinadvertentarminganddisarmingwhenunintended.

BLUEWIRE:TRUNKTRIGGERSHUNTINPUT

Thiswirewilldetermineifthevehicle’strunkhasbeenopenedusingtheOEMtransmitter,andpreventthealarm

fromtriggeringwhenthetransmitterisused. Thiswirerequiresapositivetriggerinputandmustbewiredtothe

switched+ 12volt trunkcontrol wirefrom thevehcile's keylessentry unitor, theswitched +12 voltside ofthe

vehicle'strunkreleasesolenoid.

WIRINGTHEARM/DISARMINPUTSINVEHICLESWHENTHESYSTEMISSETUPASA

STANDALONEPASSIVE(IGNITIONCONTROL)ALARMSYSTEM

For this mode of operation, be certain to set selectable features #5 for passive, #7 for delay, and #8 for 1 wire disarm.

GREEN/BLACK&GREENWIRE:ARMINPUTS

Connect these wires to chassis ground.

REDWIRE:DISARMINPUT#1

Connect this wire to an ignition source that has +12 volts when the ignition switch is turned to the on and start positions

and has 0 volts when the switch is in any other position.

REDw/BLACKTRACEWIRE:DISARMINPUT#2

Connect this wire to chassis ground.

BLUE:TRUNKSHUNTINPUT

This wire is not used for the stand alone passive alarm application.

VALET SWITCH: Plug the 2 pin connector from the valet switch into the mating 2 pin connector on the control module.

LED: Plug the 2 pin connector from the L.E.D. into the mating 2 pin connector on the control module.

Feature 1 Chirp/Flash 2 Chirp/Flash 3 Chirp/Flash Default

1)Door Lock/UL 1Sec/1Sec 3.5 Sec/3.5Sec 1 Sec/Dbl 1 Sec. 1S/1S.

2)Auto Lock O n Off Off

3)Auto Unlock O n Off Off

4)Passive Locks O n Off Off

5)Passive Arm O n Off O n

6)Voltage Sense Off O n Off

7)Door Trg. Instant Delay Instant

8)1 or 2 Wire Disarm 1 Wire 2 Wire 2 Wire

If it is necessary to change the default settings, follow the procedure listed below.

ACCESSINGTHEPROGRAMMINGMODE

A Disarm the system using either the factory transmitter or by use of the override switch.

B Turn the ignition switch to the on position.

C Press and release the valet/override switch 3 times.

Page 5

128-6627

6 of 8

Page 6

(Siren/Horn Chirps 1X, Lights Flash 1X)

D Within 3 seconds, turn the ignition switch off then on.

1. The LED flashes 1 time indicating feature #1 programming, Door Lock Timing Select.

The siren will chirp 1, 2 or 3 times indicating setting.

Use the factory Lock button of the transmitter or the factory lock switch to select.

1 Chirp, 1 Flash = 1 Second Lock/1 Second Unlock.

2 Chirps, 2 Flash = 3.5 Seconds Lock, 3.5 Seconds Unlock.

3 Chirps, 3 Flash = 1 Second Lock, Double 1 Second Unlock.

2. Press then release valet push-button switch 1x to advance to feature #2, Auto Lock On, Off.

Siren/Horn Chirps 2x, Lights Flash 2x, LED Flashes 2x Pause, 2x Pause, indicating feature 2 selected. Use Factory

Lock button of transmitter or the factory door lock switch to select.

1 Chirp, 1 Flash = Auto Locks On

2 Chirps, 2 Flash = Auto Locks Off

3. Press and release valet push-button switch 1x to advance to feature #3. Auto Unlock On, Off.

Siren/Horn Chirp 3x, Light Flash 3x, LED Flashes 3x Pause, 3x Pause, indicating feature 3 selected. Use Factory Lock