Audiovox AA-RS40CS Bedienungsanleitung

Model AA-RS40CS

Owner's Manual

FEATURES:

2 Three Button Programmable RF Transmitters

Three Channel Code Learning Receiver

Anti Code Grabbing Technology

Remote Panic In All Modes

Protected Valet/Override

Remote Start Safety Control Switch

Safe Start RF Control (Double Push Of RF Transmitter)

Selectable Automatic Timed Start Mode

7 Function LED, Arming, Armed, Disarmed, Valet, Zones 1, 2, & 3

Intrusion Alert With Memory

Audible Arm, Disarm, Defect Zone, And Intrusion Indications

Instant Siren Activation All Entry Points

Starter Disable When Armed

True Last Door Arming

Defective Zone By-Pass

On Command RF Chirp Delete

6 Tone Multi-Tone Siren

Two Stage Shock Sensor

Selectable Run Time 10 or 15 Minutes

OPTIONS:

Remote Trunk Release

Remote Keyless Entry

Illuminated entry

Remote Power Window Control

Remote Garage Door Interface

Multiple Vehicle Capable

WARNING! Be certain that the vehicle is outdoors before using this or any

remote vehicle starting device. A running engine produces dangerous carbon

monoxide fumes which can be harmful or fatal if prolonged exposure occurs.

DO NOT remote start the vehicle if it is garaged.

3 Button Remote Start Security System With

Plug-In Shock Sensor & Starter Disable

Your AA-RS40CS Remote Start Alarm System has many features and available options

some of which are selected at time of installation. For your reference, the list on

page 7 of this manual shows what features and options have been installed. Consult

your installing dealer for options that may have been installed and are not listed.

ARMING THE SYSTEM - ACTIVE:

1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk.

2. Press and release the Arm/Disarm button of your key chain transmitter one time.

The parking lights will flash once, the siren will chirp once, and the dash mounted LED

will begin to flash slowly confirming the system is armed. If you have the optional door

lock/unlock circuit installed, the doors will lock.

Note: If the siren chirped three times, then you have left a door, hood, or trunk ajar.

Simply closing that opening will provide full protection. If your vehicle has delayed

interior lighting, you may also get three chirps when arming. Once the light turns off,

you will hear one chirp confirming full arming. If the siren did not sound when

arming, then the chirps have been turned off. Refer to the section on "Eliminating

the Arm/Disarm Chirps" shown later in this manual.

SILENT ARMING - ACTIVE:

1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk.

2. Press and hold the Arm/Disarm button of your key chain transmitter for two seconds.

The parking lights will flash once, and the dash mounted LED will begin to flash slowly

confirming the system is armed. The siren will not chirp. If you have the optional door

lock/unlock circuit installed, the doors will lock.

Note: If the siren chirps three times, then you have left a door, hood, or trunk ajar.

Simply closing that opening will provide full protection. If your vehicle has

delayed interior lighting, you may also get three chirps when arming. Once the

light turns off, you will hear one chirp confirming full arming.

ARMING THE SYSTEM - PASSIVE (AUTOMATIC)

If the passive arming feature has been selected:

1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk.

The dash mounted LED will begin to flash rapidly indicating that the 30 second passive

arming timer has begun. If the LED does not begin to flash rapidly, then you have left a

door, hood, or trunk ajar. Closing this entry point will allow the arming cycle will begin.

If any entry point is opened during the 30 second arming cycle, arming will be

suspended. When all entry points are closed, the arming cycle will begin again.

At the end of the 30 seconds, the parking lights will flash once, the siren will chirp once,

and the dash mounted LED will begin to flash slowly confirming the system is armed. If

the siren did not sound when arming, then the chirps have been turned off. Refer to the

section on "Eliminating the Arm/Disarm Chirps" shown later in this manual. Passive

door locking is a selectable feature. If you have the optional door lock/unlock circuit

installed, the doors may or may not lock passively depending upon the setup during

installation.

PROTECTION WHILE THE SYSTEM IS ARMED:

Opening any protected entry point, hood, trunk, or doors will cause the alarm to trigger

immediately. The siren will sound and the parking lights will flash for 30 seconds, then

Page 2

stop and continue to monitor all protected entry points. If the thief left the door opened,

the unit will sound for six 30 second cycles then shut down, isolate the triggered zone

and continue to protect all other zones.

Whenever the system is armed, the dash mounted LED will slowly flash. This serves as

a visual deterrent to a potential thief. This LED is a very low current light emitting diode,

and will not cause the battery to drain even if left unattended for long periods of time.

Whenever the system is triggered, the vehicle's parking lights will flash for the full siren

sounding period. Optional - whenever the system is triggered, the interior courtesy light

will flash for the full siren sounding period.

Whenever the system is armed, the vehicle starter circuit is disabled, and the vehicle

will not start with the ignition key.

Whenever the system is armed, any strong impact to the vehicle will cause the shock

detector to trigger the alarm. Any lesser impact will cause the pre-detect stage of the

shock sensor to emit a few short series of warning tones from the siren.

DISARMING THE SYSTEM

As you approach the vehicle, press and release the Arm/Disarm button on the keychain

transmitter.

The parking lights will flash two times, the siren will chirp twice, and the dash mounted

LED will turn off.

If you have the optional door lock/unlock circuit installed, the doors will unlock. If you

have the optional entry illumination circuit installed, the interior light will turn on for

30 seconds or until the ignition key is switched on.

Note:If the passive arming mode was selected at time of installation, the dash mounted

LED will start flashing rapidly indicating that the system is rearming. Opening any

door will suspend the automatic arming.

If the parking lights flashed three times, and the siren chirps four times, this indicates

that the alarm system was triggered during your absence. Before turning on the ignition

key, examine the dash mounted LED's flash pattern. The number of flashes identifies

the triggered zone. For additional information, refer to INTRUSION WARNING

SIGNALS found later in this manual.

If the siren did not sound upon disarm, then the chirps have been turned off. Refer to

the section titled ELIMINATING THE ARM/DISARM CHIRPS.

SILENT DISARMING

1. As you approach the vehicle, press and hold the Arm/Disarm button of your key

chain transmitter for two seconds.

The parking lights will flash twice, and the dash mounted LED will turn off confirming

that the system is disarmed. The siren will not chirp. If you have the optional door

lock/unlock circuit installed, the doors will unlock. If you have the optional entry

illumination circuit installed, the interior light will turn on for 30 seconds or until the

ignition key is switched on.

Note: Ifthepassivearmingmodewasselectedattimeofinstallation,thedashmounted

LED will start flashing rapidly indicating that the system is rearming. Opening

any door will suspend the automatic arming.

If the parking lights flashed three times, and the siren chirps four times, this indicates

that the alarm system had been triggered in your absence. Before turning on the

Page 3

ignition key, examine the dash mounted LED's flash pattern. The number of flashes

identifies the triggered zone. For additional information, refer to INTRUSION WARNING

SIGNALS found later in this manual.

INTRUSION WARNING SIGNAL

This system will inform you if an intrusion attempt has occurred while you were away

from the vehicle. Upon disarm, the siren will chirp 4 times and the parking lights will

flash 3 times. Enter the vehicle and before turning on the ignition switch, observe the

LED flash pattern.

If the LED flashes one time...pause, one time...pause etc., then an intrusion attempt was

made by impact or a strong vibration that the shock sensor detected. Check the vehicle

for possible damage to the glass or body panels.

If the LED flashes two times...pause, two times...pause etc., then an intrusion attempt

was made to open the hood, trunk, or by an accessory triggering device. Check the

vehicle for indications of forced entry to these openings.

If the LED flashes three times...pause, three times...pause etc., then an intrusion

attempt was made to the vehicle doors. Check all doors for indications of forced entry.

Note: The LED intrusion warning indications are stored in the system's memory and will

be erased when the ignition switch is turned on.

VALET/SYSTEM OVERRIDE SWITCH

The valet switch allows you to temporarily by-pass all alarm functions, eliminating the

need to hand your keychain transmitter to parking attendants or garage mechanics.

When the system is in the valet mode, all alarm functions are by-passed, however the

remote panic feature, and the optional remote door lock/unlock will remain operational.

To enter the valet mode:

1. Start with the valet switch in the "off" position

2. Turn the ignition switch to the "on" position.

3. Within 10 seconds of step 2, move the valet switch to the "on" position.

The dash mounted LED will turn on solid indicating that the valet mode has successfully

been entered.

To return to the normal, (alarm mode), operation, move the valet switch to the "off"

position any time the ignition switch is in the "on" position.

Note: In the event that you lose your keychain transmitter or the transmitter fails to

operate the alarm system, the valet switch can be used to disarm the alarm. To

disarm the alarm:

1. Open the door with the vehicle door key. (The siren will sound)

2. Turn the ignition switch to the "on" position.

3. Move the valet/override switch to the "on" position.

The system will disarm and the vehicle can be operated normally.

Always remember to move the valet switch to the "off" position to ensure the vehicle

remains protected at all times.

ELIMINATING THE NORMAL ARM/DISARM CHIRPS

You can selectively eliminate the normal arm & disarm chirps by holding the transmitter

button slightly longer when arming or disarming. This will prevent the siren chirps for

one arm or disarm cycle. If you find this inconvenient and wish to eliminate these chirps

permanently;

Page 4

1. Start with the valet switch in the 'off" position.

2. Turn the ignition switch 'on" then 'off".

3. Within 10 seconds of turning off the ignition, move the valet switch 'on", "off', "on",

"off", "on", "off".

4. If the chirps were on before you started, the siren will emit 2 short chirps indicating

that the chirps are now off. If the chirps were off before you started, the siren will emit

one short chirp indicating that the chirps are now on.

NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the

default setting of chirps on. Repeat the above procedure to eliminate the

arm/disarm chirps.

REMOTE PANIC OPERATION

The arm/disarm button of your keychain transmitter also serves as a panic switch and will

turn the alarm on from the maximum operating range of the transmitter. In an emergency

situation, to use the panic feature, press and hold the arm/disarm button of your

keychain transmitter for 3 seconds. This will cause the lights to flash, the siren to sound,

and if the optional interior illumination circuit was installed, the interior light will flash.

To disengage the panic feature, press and hold the arm/disarm button for 3 seconds. If

you do not shut off the panic feature, the system will time out and shut off automatically

after 30 seconds.

During this mode, all normal transmitter functions are operational.

SAFETY (Red Handle) CONTROL SWITCH

The control switch allows you to temporarily disable the remote starting function of your

AA-RS40CS. To disable the unit, move the red handle control switch to the off position.

The control switch also allows you to select between 2 hour start up and 4 hour start up

when using the automatic start up timer mode. The factory preset start up time for this

mode is every 4 hours. To select between 2 or 4 hour start up timer:

1. Begin with the control switch in the on position

2. Turn the ignition switch on then off

3. Within 10 seconds, move the control switch off, on, off, on (2 switch cycles) to select

a2 hour start timer. After 10 seconds expire, theparking lights will flash and the siren

will chirp 2 times confirming that the two hour start cycle is set. Or, within 10 seconds

move the control switch off, on, off, on, off, on, off, on (4 switch cycles) to select a 4

hour start timer. The parking lights will flash and the siren will chirp 4 times

confirming that the 4 hour start timer is set.

REMOTE STARTING THE VEHICLE

The AA-RS40CS WILL NOT start the vehicle if any one of the followingconditionsexists:

1. The Vehicle Hood Is Opened.

2. The Gear Selector Is In Any Gear Other Then Park.

3. The Brake Is Depressed.

4. The Safety Control Switch Is In The Off Position.

WARNING! Be certain that the vehicle is outdoors before using this or any remote

vehicle starting device. A running engine produces dangerous carbon

monoxide fumes which can be harmful or fatal if prolonged exposure

occurs. DO NOT remote start the vehicle if it is garaged.

Page 5

To Remote Start The Vehicle:

Press and release channel 2 of your keychain transmitter two times within 2 seconds.

The vehicle will start and remain running for the pre-programmed 10 or 15 minutes. As

avisualindication, the parking lights will flash or turn on depending on the programming

set up by your installation center.

Whenyouarrive at your vehicle, disarm the alarm system by pressing and releasing the

arm/disarm button of your keychain transmitter. Enter the vehicle and turn the ignition

key to the on position.

CAUTION! Do not turn the key to the start position. This will cause the starter motor to

engagewiththealreadyrunningenginewhichcouldresultindamage. Step

on the brake pedal to disengage the remote start unit. The vehicle will

continue to run but now on it's own power.

NOTE: The engine will stop running before the expiration of the pre-programmed run

timer if you complete any of the following:

1.Pressand release channel 2 of your keychain transmitter two times within 2 seconds.

2. Depress the brake pedal.

3. Open the hood.

4. Move the red handle control switch to the off position.

5. Race the engine to above 4000 RPM.

OPERATING ON AUTOMATIC START UP TIMER MODE

The AA-RS40CS has the ability to automatically start the vehicle every 2 or 4 hours

over a 48 hour period. This feature is especially useful in cold climates where the only

means to keep the engine and engine fluids warm is to periodically start the engine.

WARNING! Be certain that the vehicle is outdoors before using this or any remote ve-

hicle starting device. A running engine produces dangerous carbon mon-

oxide fumes which can be harmful or fatal if prolonged exposure occurs.

DO NOT remote start the vehicle if it is garaged.

TO BEGIN THE AUTOMATIC START UP TIMER

1. Turn the ignition key on then off.

2. Within 10 seconds, activate the RF start command two times. (Push the second

channel button of your keychain transmitter 4 times).

The parking lights will flash and the siren will chirp 4 times indicating the timed start

mode is activated.

The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-

programmed time (10 of 15 minutes), and then shut off. This will continue for 48 hours.

NOTE:The automatic start up timer can also be initiated from the keychain transmitter.

To do this:

1. Start the vehicle using the keychain transmitter by pressing and releasing the

second channel transmitter button 2 times.

2. Shut off the vehicle using the keychain transmitter by pressing and releasing the

second channel transmitter button 2 times.

3. Within 10 seconds of step 2, activate the RF start command two times. (Push the

second channel button of your keychain transmitter 4 times).

The parking lights will flash and the siren will chirp 4 times indicating the timed start

mode is activated.

Page 6

CANCELING THE AUTOMATIC START UP TIMER

To cancel the automatic start up timer do one of the following;

1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.

2. Remote start the vehicle using your keychain RF transmitter.

ADDITIONAL REMOTE FUNCTION CHANNEL 2

The system has an additional feature, (Channel 2) ,that can be connected to a number

of different optional accessories. Some of the more common uses for this channel are:

qRemote Trunk Release

qRemote Window Close

qRemote Garage Door Interface

To operate the accessory associated with channel 2, press and hold the channel 2

button(s) of your keychain transmitter for four seconds.

NOTE:The feature that has been added to channel 2 will always be operated using the

same transmitter button that controls the remote start unit. There is no way to

move the channel 2 function to a different channel.

ADDITIONAL REMOTE FUNCTION CHANNEL 3

Thesystemhas an additional feature, (Channel 3),that can be connected to a number of

different optional accessories. Some of the more common uses for this channel are:

qRemote Trunk Release

qRemote Window Close

qRemote Garage Door Interface

To operate the accessory associated with channel 3, press and release the channel 3

button(s) of your keychain transmitter. Note: The channel 3 output will remain active for

as long as the transmitter button(s) are held. Certain accessories may take advantage

of the extended output capability of this channel. Check with your installation center for

operation of the accessory that may be connected to channel 3.

Page 7

ALARM DASH LED INDICATORS

RAPID FLASHING = PASSIVE ARMING

SLOW FLASHING = ARMED

OFF = DISARMED

ON SOLID = VALET MODE

3 FLASH... PAUSE = INTRUSION ZONE 3

2 FLASH...PAUSE = INTRUSION ZONE 2

1 FLASH...PAUSE = INTRUSION ZONE 1

ALARM SIREN CHIRP INDICATION

1 CHIRP* = ARM

2 CHIRPS* = DISARMED

3 CHIRPS = ARMING WITH ENTRY POINT OPENED

4 CHIRPS = DISARM AFTER INTRUSION

CONTINUOUS = TRIGGERED/PANIC

ALARM PARKING LAMP INDICATIONS

1 FLASH = ARM

2 FLASH = DISARM

3 FLASH = DISARM AFTER INTRUSION

CONTINUOUS FLASH = TRIGGERED/PANIC

REMOTE START SIREN INDICATIONS

1 LONG/1SHORT = RF START COMMAND ISSUED

(IF SELECTED ON)

REMOTE START PARKING LAMP INDICATIONS

1 FLASH = RF START COMMAND ISSUED

ON = RUNNING UNDER REMOTE START

CONTROL (IF SELECTED)

CONTINUOUS FLASH = RUNNING UNDER REMOTE START

CONTROL (IF SELECTED)

AA-RS40CS

SYSTEM FUNCTIONS AT A GLANCE

Andere Handbücher für AA-RS40CS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Pursuit PRO-9744 Bedienungsanleitung

Audiovox

Audiovox AA-RS20CS Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-410a Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS 600 Bedienungsanleitung

Audiovox

Audiovox AS-9234 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-350-A Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9845B Bedienungsanleitung

Audiovox

Audiovox APS-95BT2 Betriebsanleitung

Audiovox

Audiovox Keyless Entry Alarm Upgrade Module APS-30 Bedienungsanleitung

Audiovox

Audiovox PRO-9649a Bedienungsanleitung

Audiovox

Audiovox APS-30 Bedienungsanleitung

Audiovox

Audiovox PRO 9549FT3 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-510 Bedienungsanleitung

Audiovox

Audiovox UltraGuard PRO 9549UG Bedienungsanleitung

Audiovox

Audiovox APS-25C Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-4631B Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9671FT Bedienungsanleitung

Audiovox

Audiovox Prestige APS-15CH Bedienungsanleitung

Audiovox

Audiovox Prestige 128-8615 Bedienungsanleitung

Audiovox

Audiovox Auto Security AA-9300 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-8533 Bedienungsanleitung

Audiovox

Audiovox Prestige AS-9256 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-510 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-94FR Betriebsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung