Audiovox Pursuit PRO-9900 Bedienungsanleitung

128-7398

1 of 24

Page 1

Model PRO-9900

Owner’sManual

IMPORTANT !

In order to provide you with the highest level of security to your

vehicle, this system is equipped with selectable manual override circuitry. It is

possible that you will need to override you security system if the transmitter

becomes lost, or inoperative due to battery failure. Reading the sections on

"Manually Overriding Your System" is necessary to fully understand the procedure

required to enable your vehicle in such situations. In addition, the chart on the last

page of this manual has a section for the particular features and options installed

in your vehicle as well as the override method selected. Although the default

mode is "Valet Switch" operation, the system can be configured for "Custom

Code" operation for enhanced security. Confirm the override mode selected on

the last page of this manual, and familiarize yourself with the section on it's opera-

tion.

FEATURES :

!1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control

!Six Channel Code Learning Programmable Receiver

!External Superheterodyne Transceiver Antenna

!Single Or Two User Programmable W/Separate Control Outputs

!Single Button Lock/Unlock or Separate Button Lock/Unlock or Both

!Remote Keyless Entry With Optional Access Guard (must have power door

locks)

!Selectable Manual Override Mode

!New Enhanced Panic Feature (Any button other than unlock stops siren, no

change to the units state)

!Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )

!Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect

Off,CityMode)

!Safe Start Output Controlled From Channel 3 (Option Channel 3 ForTrunk, Or

For R/S)

!24 Hour Time Start Mode

!Cold Temperature Start Mode

!2 or 4 Hour Automatic Start Mode

!Parking Meter Count Down Timer On LCD Remote

!Additional Count Down Timer Mode

!Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds

To Engage)

!Improved Custom Code Override, User Selectable and Programmable

4 Button Remote Start Security System With

Plug-In Shock Sensor & Starter Disable

128-7398

2 of 24

Page 2

!Protected Push Button Valet/Override Switch

!7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming

!Intrusion Alert With Memory

!Instant Siren Activation

!Starter Disable Output

!Additional Engine Immobilizer Output, (Optional Relay Required)

!True Last Door Arming (Hardwire Only)

!Defective Zone By-Pass

!Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)

!6 Tone Mini Siren

!Car Horn Output For Additional Alarm Response (Improved Timing To Mini-

mize RF Interference.)

!Additional Negative Trigger Input (Hood and Trunk)

!RF Inhibit With Ignition On

!Parking Light Flasher (Relay On Board)

!Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger and “City Mode”)

!Audible Arm, Disarm, Defect, and Tamper Chirp Indications

!Headlight Control Output

!Illuminated Entry Control Output

!Active or Passive Arming Selectable

!Programmable Auto Lock On / Off

!Programmable Auto Unlock On / Off/Drivers Door/All Doors

!Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec

L/ Dbl. U/L

!Programmable Active or Passive Door Locks

!User Programmable Permanent Chirp Delete

!On Command RF Chirp Delete from Transmitter Or Selectable Through

Software

!Dome Delay Learn Circuitry (Patent Pending)

OPTIONS :

!Remote Trunk Release (must have electric trunk release)

!Remote Keyless Entry (must have power door locks)

!Multiple Vehicle Capable

!Remote Power Window Roll Up

!Remote Garage Door Interface

CAUTION! Be certain that the vehicle is outdoors before using this or any remote

vehicle starting device. A running engine produces dangerous car-

bon monoxide fumes which can be harmful or fatal if prolonged expo-

sure occurs. DO NOT remote start the vehicle if it is garaged.

YOUR“CODEHOPPING“TRANSMITTERS

The transmitters included with your new security system use the most advanced

and secure form of radio frequency transmission available on any current auto-

motive security system. Some of today’s sophisticated auto thieves use a device

128-7398

3 of 24

Page 3

known as a code grabber, which will receive and store the signal from your

keychain transmitter and re-transmit at a later time to disarm your system.

Your Keeloq Code Hopping transmitters will change their signal every time the

button is pressed, so when a thief grabs then re-transmits your signal, the alarm

system

will not

respond.

If your transmitter button is pressed more than fifty times while it is out of range of

the vehicle (children playing with your keys), the transmitter will not operate when

you return to the vehicle, and will need to be re-aligned to the

receiver. To do this, simply press button 1, (lock), two times within

a one second time period. The system will now respond to that

transmitter each time a button is pressed.

NOTE: This system is custom configurable and can be set

up to operate with a number of options controlled from any trans-

mitter button or button combination. For reference, we will de-

scribe operation assuming that your system is programmed for

separate lock and unlock buttons. Also reference will be made to

the icons as shown on the buttons left.

NOTE: The LCD based remote will be explained in detail further in

this manual See "System Status" described later in this manual.

Consult your installation center if your system has been config-

ured differently.

NOTE: Your system has the option of using a siren, the vehicle

horn, or both for the sounding device. Where the siren is refer-

enced below, the horn or both may in fact chirp, or beep.

ARMINGTHESYSTEM-ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid and trunk lid.

2. Press and release Lock/Arm button on the keychain transmitter.

"The dash mounted LED begins to flash slowly.

"Parking Lights flash one time.

"Siren sounds one chirp.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or

hood lid ajar. Simply close the opened entry point to provide full protec-

tion. If the siren "chirped" three times, sometime after arming, the

exclusive delayed dome light learn circuit has been programmed and

the system detected a open entry point after the learned delay expired.

Again, closing the hood, trunk, or doors will correct the problem and you

do not need to disarm the system to make the correction. If the siren/

horn did not sound when arming, then the chirps have been turned off

and you should refer to the section titled "ELIMINATING THE ARM/DIS-

ARM CHIRPS" in this manual.

#Doors Lock - Optional

NOTE: If the optional Headlamp illumination feature has been added, and has

been selected for operation when arming, as an added convenience, the

system will turn on the headlights when the system is armed.

SILENT ARMING - ACTIVE (Must be activated during programming)

1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.

2. Press and hold the Lock/Arm button on the keychain transmitter for 2

seconds.

128-7398

4 of 24

Page 4

"The dash mounted LED begins to flash slowly.

"Parking Lights flash one time.

"Siren will not sound.

If the siren "chirped" three times, sometime after arming, the exclusive delayed

dome light learn circuit has been programmed and the system detected a open

entry point after the learned delay expired. Closing the hood, trunk, or doors will

correct the problem and you do not need to disarm the system to make the

correction.

#Doors Lock - Optional

NOTE: If the optional Headlamp illumination feature has been added, and has

been selected for operation when arming, as an added convenience, the sys-

tem will turn on the headlights when the system is armed.

The LCD Remote has the following response:

ARMINGTHESYSTEM-PASSIVE(AUTOMATIC)

(Must be activated during programming)

1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and

trunk lid.

"The dash mounted LED begins to flash rapidly, indicating 30 second passive

arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle

will immediately suspend automatic arming and the 30 second passive arm-

ing cycle will re-start when all doors are closed. At the end of the passive

arming cycle;

"The dash mounted LED begins to flash slowly.

"Parking Lights flash one time.

"Siren sounds one chirp

If the siren did not sound when arming, then the chirps have been turned off and

youshouldrefer to the section titled “ELIMINATINGTHEARM /DISARMCHIRPS“

in this manual.

#Doors Lock - Optional

Door locking during passive arming is a selectable feature. The alarm can be

programmed to allow the doors to lock only when arming using the keychain

transmitter and they will not automatically lock during passive arming.

PROTECTIONWHILETHESYSTEMIS ARMED

"Opening any protected door, hood or trunk lid will cause the alarm to imme-

diately sound. The alarm will continue to sound for 30 seconds, then stop and

continue to monitor all protected entry points. If the thief left a door opened, the

alarm will sound for six 30 second cycles, remain armed and ignore that trig-

gered zone.\

"Whenever the system is armed, the dash mounted LED indicator will slowly

flash. This serves as a visual deterrent to the potential thief. The LED is a very

low current bulb and will not cause the vehicle’s battery to drain, even when left

unattended for extended periods.

"Whenever the system is triggered, the vehicle’s parking lights will flash for the

full 30 second alarm cycle, attracting visual attention to the vehicle.

"Optional - Whenever the system is armed, the vehicle’s starting circuit will be

bypassed. If the thief should choose to ignore the siren, the vehicle can not be

128-7398

5 of 24

Page 5

started.

"Any mild impact to the vehicle’s glass will cause the alarm to sound a short

series of warning tones.

"Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full

30 second alarm cycle.

NOTE: If the optional interior illumination circuit was installed, the interior light

will flash as well for the full 30 second alarm cycle.

DISARMINGTHESYSTEM

NOTE: If the optional 2 step door unlock circuit is installed, when the unlock

transmitter button is activated, the drivers door only will unlock, pressing the

unlock button a second time will cause all doors to unlock.

NOTE: If your transmitter has been configured with single button Lock/Unlock, to

activate the all door unlock feature operate the Lock/Unlock button a second

time within 3 seconds of the first unlock command.

1. As you approach the vehicle, press and release the Unlock/Disarm button on

the keychain transmitter.

"The dash mounted LED turns off.

The LED will start flashing rapidly, indicating that the system is re-arming

automatically. Open any door to suspend the automatic arming.

"Parking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in your

absence. Before turning the key on, examine the LED to identify which zone was

triggered.

"Siren sounds two chirps.

If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before

turning the key on, examine the LED and refer to the INTRUSION WARNING

SIGNALS section of this manual to identify which zone was triggered.

If the siren did not sound when disarming, then the chirps have been turned off

and you should refer to the section titled “ELIMINATING THEARM / DISARM

CHIRPS“ in this manual.

#Doors Unlock - Optional

#2 Step Doors Unlock - Optional

NOTE: If the optional Headlamp illumination feature has been added and has

been selected for operation when disarming, as an added convenience, the

system will turn on the headlights when the system is disarmed.

SILENT DISARMING (Must be activated during programming)

Note: If the optional 2 step door unlock circuit is installed, when the unlock

transmitter button is activated, the drivers door only will unlock, pressing the

unlock button a second time will cause all doors to unlock.

NOTE: If your transmitter has been configured with single button Lock/Unlock as

shown, to activate the all door unlock feature operate the Lock/Unlock button a

second time within 3 seconds of the first unlock command.

1. Press and hold button the Unlock/Disarm button on the keychain transmitter for

2 seconds.

"The dash mounted LED turns off.

The LED will start flashing rapidly, indicating that the system is re-arming

128-7398

6 of 24

Page 6

automatically. Open any door to suspend the automatic arming.

"Parking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in your

absence. Before turning the key on, examine the LED to identify which zone was

triggered.

"Siren will not sound.

If the siren sounds 4 chirps, then the alarm was triggered in your absence.

Before turning the key on, examine the LED and refer to the INTRUSION

WARNING SIGNALS section of this manual to identify which zone was triggered.

#Doors Unlock - Optional

#2 Step Doors Unlock - Optional

NOTE: If the optional Headlamp illumination feature has been added and has

been selected for operation when disarming, as an added convenience, the

system will turn on the headlights when the system is disarmed.

WHILETHESYSTEMISSOUNDING

If during a triggered state, you wish to shut off the siren without disarming your

security system, simply press and release any transmitter button other than the

Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully

armed and protected. This feature is particularly useful if you are aware of children

playing near your vehicle that may accidently trigger your security system. In this

case you can cancel the siren sounding without disarming your alarm.

INTRUSIONWARNINGSIGNALS

This system will inform you if an intrusion attempt has occurred while you were

away from the vehicle. If an intrusion attempt has occurred, the siren will

chirp 4 times and the parking lights will flash 3 times when disarming the

system. Enter the vehicle and observe the red dash mounted LED to identify

which zone was triggered.

$If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the shock sensor, or an accessory trigger-

ing device that may have been added to the system.

%If the LED is flashing two times...pause...two times...pause...etc., then

an intrusion attempt was made to a hood or trunk pin switch that was

added to the system or to a light activated entry point if the alarm was

installed using the voltage sensing feature.

&If the LED is flashing three times...pause...three times...pause...etc.,

then an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will

only be erased when the ignition key is turned on.

VALETSWITCH

The valet switch allows you to temporarily bypass all alarm functions, eliminating

the need to hand your transmitter to parking attendants or garage mechanics.

When the system is in valet mode, all alarm functions are bypassed, however the

remote panic feature and remote door locks will remain operational. In addition,

the parking lights will flash to indicate locking and unlocking. To use the valet

mode, the system must first be disarmed either by using your keychain transmit-

ter or by activating your personalized manual override code.

1. Enter the vehicle and turn the ignition key to the on position.

2. Press and hold the valet pushbutton switch until the dash mounted

128-7398

7 of 24

Page 7

LED turns on solid. The system will remain in the valet mode.

3. To return to normal operation, press and release the pushbutton switch

any time the ignition is on.

NOTE: Always remember to return the system to normal operation. This will

ensure that the vehicle remains protected at all times.

MANUALLYOVERRIDINGYOURSYSTEM:

USINGTHE VALETSWITCHMANUALOVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter.This is

necessary, since you will need the ability to operate your vehicle if the transmitter is lost or

its battery fails. If your system has been selected for Valet Switch manual override as

indicated on the last page of this manual, to bypass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet pushbutton switch.

The alarm system will stop sounding and enter the (bypass) mode. You can now

start and operate the vehicle normally.

Typically this override mode is used only if the transmitter has become inopera-

tive.

PROGRAMMINGYOURCUSTOMOVERRIDECODE:

Unlike override switches easily found, and defeated, this security system allows the

consumer to program a personal override code, offering a higher level of security. To take

advantage of this option, programmable feature # 10 must be selected for the Custom

Code Option. Consult your installation center for programming details. The system

comes from the factory with a pre-programmed override code of 11. To change this

default override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the valet/override switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and

releasing the pushbutton switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off

then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and

releasing the pushbutton switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by

flashing the LED, first indicating the 10ths digit, pause and then the units digit.

The unit will report the new code three times with a one second pause between

each code, then the system will begin arming. If the LED flash pattern reports the

previously stored code, the new code was not entered correctly. Please repeat

steps 1 through 7 above considering the following.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not

recognize a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert

back to the last successfully stored code.

128-7398

8 of 24

Page 8

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to “52” you would do

the following:

1. Disarm the system by use of the transmitter or by use of the emergency

override sequence.

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the valet/override switch, 3 times.

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the pushbutton switch to set

the tenths digit.

(As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch

off then on.

7. Within 10 seconds, begin to press and release the pushbutton switch to set

the units digit.

(As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash

pattern.

You will note the LED flashing five times, pause, and then flash two times, pause.

This pattern will be repeated three times indicating the new code (52) has been

accepted and stored in memory.

NOTE: If after step 7, the LED flashes a code other than what was just entered,

this indicates that the code has not been changed. You will have to repeat

steps 1 through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0

(Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert

back to the last successfully stored code.

MANUALLYOVERRIDINGYOURSYSTEM:

USINGTHECUSTOMCODEOVERRIDE

Assuming the override code programmed has not been changed, and the default

override code of 11 is in the system's memory.

1. Enter the vehicle and turn the ignition switch to the on position.

NOTE: The siren will sound.

2. Within 5 seconds, press and release the pushbutton switch 1 time.

3. Within 5 seconds, turn the ignition switch off then on.

4. Within 5 seconds, press and release the pushbutton switch 1 time.

5. Turn the ignition switch off then on and start the vehicle.

NOTE: If you have changed the programmed override code then substitute your

new code tenths for step 2 above, and units for step 5 above.

ELIMINATINGTHENORMALARM/ DISARMCHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any

time you arm or disarm the system, if the feature has been activated, simply by

holding theARM or DISARM button for two seconds. If you find the normal arming

and disarming chirps annoying, they can be turned off permanently, eliminating

the need to hold the ARM / DISARM button for 2 seconds. To do this:

128-7398

9 of 24

Page 9

1. Turn the ignition key on then off.

2. Within 10 seconds, press and release valet switch three times.

3. If the chirps were on before you started, then you will hear two chirps indicat-

ing they have been turned off.

If the chirps were off before you started, then you will hear one chirp indicating

they have been turned on.

NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator

and 3 chirp defective zone indicator will always operate. Since these are

important warnings to you that something has happened, they cannot be

eliminated.

NOTE: Your system must be programmed by the installation center to en-

able this feature.

REMOTEPANICOPERATION

The Lock or Unlock button on your keychain transmitter also functions as a panic

switch for use in emergency situations. To use remote panic,

1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or

more seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter

again for 3 seconds. If the button is not pressed, the alarm will automatically

stop after 30 seconds. Also if any transmitter button other than the Lock or

Unlock button is pressed and released, the Panic mode will be turned off

immediately. The normal function of this transmitter button will be suspended

during the Panic sounding period.

3. During the panic mode, the Lock and Unlock buttons can be used to lock and

unlock the doors, (if the option is installed), however once the unlock/disarm

button is pressed, the vehicle's starter inhibit device, (where installed) will be

disabled allowing the vehicle to start.

NOTE: While in the Panic mode, pressing and releasing the Lock or Un-

lock buttons will, if the option is installed, lock and unlock the doors respectively.

While in the panic mode, anytime the Unlock button is pressed, the panic feature

will continue for the allotted 30 seconds, however, the security system will be

disarmed allowing the vehicle to start.

RFSHOCK SENSORMODESELECTION

The way in which your alarm system reacts to threatening vibrations, created by

attempts to enter the vehicle by breaking a window, is adjustable by the transmitter

immediately after arming. There are 4 modes of operation that can be selected

by the operator:

1. Normal Operation (default mode)

In this mode, any strong vibrations will cause the siren to sound (full

detect) for 30 seconds. Any lesser vibration will cause the siren to emit

about 6 short warn away chirps, (pre-detect).

2. Stage 1 (Omit pre-detect)

In this mode, the warn away chirps created by the lesser vibration will be

deleted. If strong vibration occurs, the siren will sound.

3. Stage 2 (Omit pre & full detect)

In this mode, both the pre-detect stage and the full trigger stage of the sensor

are defeated. The unit will not react to vibration of any magnitude.

NOTE: Shock Sensor Icon Is Displayed On The LCD Panel.

4. Stage 3 (City Mode)

128-7398

10 of 24

Page 10

In this mode, the pre-detect chirps will change from six pre-warning tones to

a full 10 seconds of warning chirps.

The full detect trigger duration will be reduced from 30 seconds to 15 seconds.

NOTE: Setting the stage of the shock sensor will be effective for one arming cycle

only. Once the system has been disarmed, the very next arming cycle will

cause the sensor to default to the normal operation stage.

To change or adjust the shock sensor, press and release the ARM button of you

keychain transmitter.

1.Within 2 seconds of arming, press and release the ARM button 1 time, to

defeat the pre-detect stage of the shock sensor. (The lights will flash and the

siren will chirp once.)

2.Within 2 seconds of step 1, press and release the ARM button 2 times, to

defeat the pre and full detect stages of the shock sensor. (The lights will

flash and the siren will chirp twice.)

3.Within 2 seconds of step 1, press and release the ARM button 3 times to

enter the "City Mode" of operation. (The lights will flash and the siren will chirp

three times.)

While under control of the remote start the system can be programmed to allow

you to shunt the shock sensor from the transmitter. If the system has been such

programmed, simply press the lock button of your keychain transmitter anytime

during the remote start cycle. The shock sensor will be shunted for the entire run

cycle and will resume normal operation after the remote start unit shuts off.

Check with your installation center to determine if this feature has been pro-

grammed into your system.

SAFETY(RedHandled ) CONTROLSWITCH

The control switch allows you to temporarily disable the remote starting function

of your system. To disable the unit, move the red handled control switch to the off

position.

The control switch also allows you to select between 2 hour start up and 4 hour

start up when using the automatic start up timer mode. The factory preset start up

time for this mode is every 4 hours. To select between 2 or 4 hour start-up timer:

1. Begin with the control switch in the on position.

2. Turn the ignition switch on then off.

3. Within 10 seconds, move the control switch off, on, off, on (2 switch cycles) to

select a 2 hour start timer. After 10 seconds expire, the parking lights will

flash and the siren will chirp 2 times confirming that the two hour start cycle is

set. Or, within 10 seconds move the control switch off, on, off, on, off, on,

off, on (4 switch cycles) to select a 4 hour start timer. The parking lights will

flash and the siren will chirp 4 times confirming that the 4 hour start timer is

set.

REMOTESTARTINGTHEVEHICLE

The system WILL NOT start the vehicle if any one of the following conditions

exists:

1. The Vehicle Hood Is Opened.

2. The Gear Selector Is InAny Gear Other Then Park.

3. The Brake Is Depressed.

4. The Safety Control Switch Is In The Off Position.

WARNING! Be certain that the vehicle is outdoors before using this or any remote

vehicle starting device. A running engine produces dangerous carbon

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Audiovox

Audiovox AS-9234 Bedienungsanleitung

Audiovox

Audiovox AA-RS40CS Bedienungsanleitung

Audiovox

Audiovox Car Security System APS-610 Bedienungsanleitung

Audiovox

Audiovox Prestige 128-8615 Bedienungsanleitung

Audiovox

Audiovox Platinum+ APS 687C Bedienungsanleitung

Audiovox

Audiovox AA-9347 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-5730A Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-300R Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9344WOT Bedienungsanleitung

Audiovox

Audiovox APS 750a Bedienungsanleitung

Audiovox

Audiovox 5BCR07 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO 2000S Anleitung zur Verwendung

Audiovox

Audiovox Prestige Platinum+ APS-25N Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-8117 Bedienungsanleitung

Audiovox

Audiovox 5BCR10P Betriebsanleitung

Audiovox

Audiovox Prestige APS-15KB Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9344FT Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9675FT4 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-8539 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-150-A Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25HJ Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9671FT Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO9776C Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung